Page 1 June 1999 The information in this document is subject to change without notice and should not be construed as a commitment by the manufacturer. The manufacturer assumes no responsibility for any errors that might appear in this document. The software described in this document is furnished under a license and may be used or copied only in accordance with the terms of such license.
Page 2 The FCC wants you to know... This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Page 3 Federal Communications Commission (FCC) PART 68 Warning This equipment complies with Part 68 of the FCC Rules. On the bottom of the computer is a label that contains, among other information, the FCC Registration Number and Ringer Equivalence Number (REN) for this equipment.
Page 4: Canadian Doc Notice
CANADIAN DOC NOTICE This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the Radio Interference Regulation of the Canadian Department of Communications. "Le présent appareil numérique n’èmet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de la class B prescrites dans le Règlement sur le brouillage radioélectrique édicté...
Page 5: Table Of Contents
Chapter 1 ... 1 Introducing the Notebook... 1 Features and Controls ... 2 Optional Devices ... 7 Unpacking & Checking the Equipment... 7 Identifying Parts of the Notebook... 8 Installation and Initial Setup ... 16 Chapter 2 ... 21 The BIOS Setup Program... 21 Introduction ...
Page 6 The FIR Module ... 58 Multimedia Sound System ... 60 The CD-ROM Module... 62 Audio Volume Control ... 63 Chapter 4 ... 65 Peripherals ... 65 Additional Equipment... 65 Connecting Peripheral Devices... 69 Chapter 5 ... 77 The Power System ... 77 The AC Adapter...
Page 7 Chapter 6 ... 97 Expansion Options... 97 System Memory Expansion ... 97 Installing Memory Cards ... 97 Removing and Installing Modules ... 98 Replacing the Battery Module ... 101 Removing and Installing HDD Modules... 101 Removing and Installing the FDD Module ... 103 Removing and Installing a Mini PCI Card...
Page 8 Figure 1-1: Right Front View with Display Panel Closed... 8 Figure 1-2: Left Front View with Display Panel Closed... 10 Figure 1-3: Rear View of Notebook ... 12 Figure 1-4: Right Front View with Display Panel Open ... 13 Figure 1-5: System Status Indicator Panel ... 14 Figure 1-6: Connecting the Power Cord and the AC Adapter...
Page 9 Figure 5-5: Connecting the AC Adapter to the Notebook’s AC port ... 84 Figure 6-1: Removing the Memory Door and Installing the Memory Card ... 98 Figure 6-2: Removing the CD-ROM Module ... 99 Figure 6-3: Installing the CD-ROM Module... 100 Figure 6-4: Removing the HDD Module (A)...
Page 10 Abbreviations Abbreviation Meaning ACPI Advanced Configuration and Power Interface Advanced Power Management (This Notebook supports APM 1.2) BIOS Basic Input/Output System CMOS Complementary Metal Oxide Semi-conductor DIMM Dual In-line Memory Module Direct Memory Access DRAM Dynamic Random Access Memory Digital Versatile Disc EDO RAM Extended Data Out Random Access Memory Integrated Drive Electronics (internal hard disk drive interface)
Page 11 ABOUT THIS GUIDE This guide describes how to operate, configure, and troubleshoot the Note- book computer. With this easy to use guide, you will be able to quickly familiarize yourself with all aspects of the Notebook computer. Organization This guide contains the following: Chapter 1: Introducing the Notebook - This chapter identifies the external components of the Notebook and provides a quick reference to the Notebook functions.
Page 12 Chapter 8: Caring for Your Notebook - This chapter covers some of the basic maintenance procedures you may want to familiarize yourself with. introduces proper methods of cleaning the case, the screen, the FDD drive, as well as some helpful tips on handling diskettes. Appendix A: Troubleshooting - In a question and answer format, this section provides you with solutions to possible problems that may arise.
Page 13: Chapter 1
HAPTER NTRODUCING THE OTEBOOK Your new Notebook features the most innovative advances in portable computing technology. It combines state-of-the-art ergonomics with sophisticated architecture to provide you with a personal computer that is compact, powerful, and easy to use. The modular design of the Notebook provides maximum expandability without compromising portability.
Page 14: Features And Controls
Notebook User’s Guide Features and Controls This section provides an overview of the Notebook’s features. For more detailed information see the Specifications section in Appendix B. Your Notebook includes the following features: The microprocessor (CPU) is the heart and brain of the computer. It performs all the computing functions and orchestrates the actions of the system.
Page 15 LCD VGA Display Your Notebook’s VGA display is one of three models: = Color TFT-14.1" LCD panel supporting 1024 x 768 XGA resolution = Color TFT-15.0" LCD panel supporting 1024 x 768 XGA resolution = Color TFT-15.0" LCD panel supporting 1400 x 1050 SXGA resolution VGA Graphics Accelerator and Video Subsystem This Notebook is equipped with an ATI 3D RAGE Mobility-P VGA AGP controller chip offering the following features:...
Page 16 Notebook User’s Guide The Touch Pad The Notebook features a touch pad pointing device with two buttons. This pressure-sensitive pointing device allows you to move the cursor around the screen and make selections just as one would with a conventional mouse. A unique function called double tapping allows you to make selections within a software program or execute software applications without having to remove your hands from the touch-type position.
Page 17 Chapter 1: Introducing the Notebook PCMCIA Sockets An ACPI-compliant PCMCIA R2.0 host adapter supports one type III PCMCIA card or two type II PCMCIA cards. The PCMCIA sockets support hot insertion and removal and can accommodate SRAM, OTPROM, FLASHROM and Mask ROM memory cards of up to 64MB, MODEM/LAN cards and 10.5mm removable HDD.
Page 18 Notebook User’s Guide FIR Port For convenience, the Notebook features an FIR Port (on the rear panel) that allows wireless, serial communication between the Notebook and other FIR equipped devices such as a printer or another computer. The FIR Port allows both the sending and receiving of data.
Page 19: Optional Devices
Optional Devices There are several optional products you can purchase to further enhance the utility and versatility of your Notebook computer. = HDD Module (factory option) = CD-ROM Module = DVD Module = LS120 Module (factory option) = Zip Module = Mini PCI 56K Data/Fax/Modem (factory option) = TV-out Adapter = S-Type TV Video and Audio cable...
Page 20: Identifying Parts Of The Notebook
Notebook User’s Guide Identifying Parts of the Notebook The illustrations that follow identify the various features and external components of the Notebook computer. Familiarizing yourself with these terms will help you as you read the rest of the manual. Right Front View (Panel Closed) Figure 1-1: Right Front View with Display Panel Closed Removable Battery Module Your Notebook comes equipped with a factory-installed battery pack module.
Page 21 Removable HDD Module Your Notebook comes equipped with a factory-installed HDD module. If you find that your Notebook is running low on disk space, the HDD can be removed an replaced with a higher capacity HDD (up to 16GB). Kensington Lock This port is for locking the Notebook PC to a desk for security.
Page 22: Figure 1-2: Left Front View With Display Panel Closed
Notebook User’s Guide Left Front View (Panel Closed) Figure 1-2: Left Front View with Display Panel Closed FDD Module or LS120 Module Your Notebook comes equipped with a factory-installed FDD module or LS120 Module. Insert 3.5-inch floppy diskettes into the floppy disk drive. Press the eject button eject a diskette from the floppy disk drive.
Page 23 Audio Headphone-out Connector This stereo jack is used to connect external speakers or headphones. Please refer to Chapter 3 for information on using Audio control hot keys. The Audio jacks are three-terminal stereo jacks but are used as two terminal mono jacks. They are not compatible with two-terminal mono plugs.
Page 24: Figure 1-3: Rear View Of Notebook
Notebook User’s Guide Rear View Several I/O ports are located on the rear side of the Notebook. Starting from left to right, the rear-side ports are introduced below. Please refer to Figure 1- 3 for assistance in locating these ports. Figure 1-3: Rear View of Notebook Serial (COM) Port This port is used to connect RS-232 serial devices to the Notebook.
Page 25: Figure 1-4: Right Front View With Display Panel Open
Chapter 1: Introducing the Notebook External Keyboard or PS/2 Mouse Port This port is for connecting either an external keyboard or a PS/2 mouse. Right Front View (Panel Open) The Notebook has two LCD panel release buttons located on the left and right side panels.
Page 26: Figure 1-5: System Status Indicator Panel
Notebook User’s Guide System Status Indicators The System Status indicators inform you of the Notebook’s current operating status at a glance. The different LED indicators are from left to right: AC Power, Battery Power, Activity, Numlock, Caps Lock, and Scroll Lock. Refer to chapter 3 for a detailed description of these indicators.
Page 27 Touch Pad The touch pad is a pressure sensitive pointing device that provides all the features of a mouse. Although its operation differs from a mouse, its function is quite the same: to move the cursor around the screen. Please refer to Using the Touch Pad, in Chapter 3 for more information.
Page 28: Installation And Initial Setup
Notebook User’s Guide Installation and Initial Setup If you are unfamiliar with computers, this section guides you through turning on your Notebook for the first time. This section also explains what you need to do after turning on your Notebook. Experienced computer users may need only read this section while using the rest of the manual merely as a reference.
Page 29 4. Plug the Notebook into its power source and press the power button. If the Notebook does not power up, check the connections between the wall outlet, the AC Adapter, and the Notebook. If the Notebook still does not power up, please refer to Appendix A, Troubleshooting. 5.
Page 30 Notebook User’s Guide Installing an Operating System When starting the computer for the first time, please be aware that you must have an Operating System (OS) program installed on the hard drive. You probably have an OS program already installed on your Notebook. If your dealer did not install an OS for you, please consult your OS Software manuals for instructions on how to install an OS onto your hard disk drive.
Page 31 A Word about Ergonomics Ergonomics is the study of how people with their different physical characteristics and ways of functioning relate to their working environment (the furnishings and machines they use). incorporate comfort, efficiency, and safety into the design of keyboards, computer desks, chairs, and other items in an effort to prevent physical discomfort and health problems in the working environment.
Page 32 Notebook User’s Guide Key Combinations [Fn] + [Fn] + [Fn] + [PageUp] [Fn] + [PageDn] [Fn] + [F8] [Fn] + [End] [Fn] + [number] [Fn] + [Esc] [Fn] + [A] or [Fn] + [Q] This concludes Chapter 1. The next chapter covers the BIOS Setup program. Definitions Increases display brightness Decreases display brightness...
Page 33: Chapter 2
BIOS S ETUP Introduction The BIOS (Basic Input and Output System) Setup program is a menu driven utility that enables you to make changes to the system configuration and tailor the operation of your Notebook to your individual work needs. A ROM-based configuration utility displays the system’s configuration status and provides you with a tool to set system parameters.
Page 34: Navigating Through The Bios Setup Program
Notebook User’s Guide Navigating through the BIOS Setup Program The Setup program has been designed to make it as easy to use as possible. It is a menu driven program, which means you can scroll through the various directories and make your selections among the various predetermined choices. If you accidentally make a setting and do not know which one to switch back to, use the BIOS hot keys to return to the previous value.
Page 35 Accessing the BIOS Setup Program To access the BIOS Setup program, press the F2 key after the Notebook has run through its POST. The Menu Bar The top of the Setup screen has a menu bar with the following selections: Main Use this menu to make changes to the basic system configuration.
Page 36 Notebook User’s Guide Legend Key [F1] or [Alt] + [H] [Esc] [ ÿ ÿ ÿ ÿ ] or [ " " " " ] [ # # # # ] or [ $ $ $ $ ] [Tab] [Shift]+[Tab] [F5] [F6] [F9] [F10]...
Page 37 General Help In addition to the Item Specific Help window, the BIOS Setup program also provides a General Help screen. This screen can be called up from any menu by simply pressing the function key [F1], or the [Alt] + [H] combination. The General Help screen lists the legend keys with their corresponding alternates and functions.
Page 38: The Main Menu
Notebook User’s Guide The Main Menu When the Setup program is accessed, the following screen appears: Main System Devices System Time: System Date: Floppy Drive Hard Disk Quiet Boot Video Display Device Television Port: Television Type: System Memory: Extended Memory: F1 Help Exit Figure 2-1: The Setup Main Menu...
Page 39: Hard Disk
Hard Disk The manufacturer and model name of your Notebook’s hard drive will be displayed in this field. You do not need to make changes to this field. This is a display only field. Quiet Boot This field allows you to display the diagnostic screen during bootup. There are two possible settings: = Enabled = Disabled...
Page 40 Notebook User’s Guide Television Type This field allows you to define the protocol for the Notebook’s TV port. There are two possible settings: = NTSC = PAL The default value for this field is: NTSC System Memory This field displays the amount of conventional memory detected by the system during bootup.
Page 41: The System Devices Menu
The System Devices Menu Selecting System Devices from the menu bar displays the System Devices Menu. Please see Figure 2-2. System Devices Main IDE Controller FDD Controller Internal touchpad Serial Port Infrared Port Parallel Port Mode: Base I/O address: Interrupt: DMA Channel: Modem Select Item...
Page 42: Fdd Controller
Notebook User’s Guide FDD Controller This field allows you to configure the FDD Controller for the Notebook’s floppy disk drive. Available options for this field are: = Disabled = Enabled Select Disabled if an FDD is not installed. The default value for this field is: Enabled Internal Touchpad This field allows you to configure the Internal Touchpad.
Page 43: Infrared Port
Infrared Port This field allows you to configure the Notebook’s Fast Infrared (FIR) communication module. The following configuration options are available: = Off = Customized = Auto The default value for this field is: Off Base I/O address / IRQ Use this option to choose the I/O (port) address for the Infrared Port.
Page 44 Notebook User’s Guide DMA Channel (Only Available for Fast IR Mode) This field allows you to configure the Infrared port’s DMA Channel. The following options are available: = DMA 0 = DMA 1 = DMA 2 = DMA 3 This field is only available when the Infrared Port Mode field is set to FIR. The default setting is: DMA 0 Parallel Port This field allows you to configure the Notebook’s Parallel Port.
Page 45 Base I/O address Use this option to choose the I/O (port) address for the Parallel Port. The available options are: = 378 = 278 = 3BC This field is only available when the Parallel Port is set to Customized. The default setting is: 378 Interrupt Use this option to choose the IRQ for the Parallel Port.
Page 46: The Security Menu
Notebook User’s Guide The Security Menu The Notebook’s advanced system of security allows you to set a password to prevent unauthorized access to system resources, data, and the BIOS Setup program. This section covers each parameter of the Security Menu. Selecting Security from the menu bar displays the following menu: System Devices Main...
Page 47: The Power Menu
Set System Password Enter New Password Confirm New Password Type the password and press the [Enter] key. You can type up to eight alphanumeric characters. Symbols and other keys are ignored. To confirm the password, type the password again and press the [Enter] key. The System password is now set.
Page 48: Figure 2-4: The Power Menu
Notebook User’s Guide these features will extend the life of the battery pack between charges. To make changes to power management settings, select Power from the menu bar. The following menu appears: Main System Devices Power Management Mode Standby Time-out: Suspend Time-out: Suspend Mode: Resume On Modem Ring:...
Page 49 When this field is specified as Max. Performance, optimal system perfor- mance is achieved with some power conservation. The remaining fields within the Power Menu will be set to pre-defined values that ensure maximum performance. When set to Max. Power Savings, system power will be conserved to its greatest amount.
Page 50 Notebook User’s Guide Suspend Time-out This field determines the amount of time the system needs to be in Standby mode before entering the Suspend to RAM mode. In this mode, all system states are saved to RAM before entering Suspend mode. Disabled, the system cannot suspend operations.
Page 51 Resume On Time of Day This option allows you to enable the system to resume at a specific time. The possible options are: = Disabled = Enabled If you set this field to Enabled, you must set the Resume Time field as well. The default value for this field is: Disabled Resume Time This option allows you to specify the time the system will resume.
Page 52: The Boot Menu
Notebook User’s Guide The Boot Menu The Boot Menu allows the user to specify the order in which the Notebook is to check for a device to boot the system. To make changes, select Boot from the menu bar. The following screen appears: System Devices Main Floppy/Super Disk...
Page 53: The Exit Menu
The Exit Menu Once you have made all of your selections from the various menus in the Setup program, you should save your changes and exit Setup. Select Exit from the menu bar to display the following menu: System Devices Main Save Changes and Exit Discard Changes and Exit...
Page 54 Notebook User’s Guide Once your selections have been saved, the Setup program displays the following message: Save configuration changes and exit now? The next time you bootup the Notebook, the BIOS will attempt to load the values you saved in Non-Volatile memory. If these values cause the system boot to fail, reboot and press [F2] to enter the Setup program.
Page 55 You can now select Save Changes and Exit or make other changes before saving the values to Non-Volatile RAM. Load Last Saved Values This option allows you to discard the selections you have made and restore the values you previously saved. After selecting this option, all selections are updated, and the following message is displayed: Setup Confirmation Load previous configuration now?
Page 56 Notebook User’s Guide...
Page 57: Chapter 3
PERATION Introduction This chapter provides information pertaining to the Video Display Controls of the Notebook used to adjust the appearance of the LCD screen. Also included in this chapter is a brief overview of the keyboard, a description of the status indicators, as well as descriptions of the touch pad, FIR module, and the Notebook’s audio features.
Page 58: Some Important Keys On The Keyboard
Notebook User’s Guide Some Important Keys on the Keyboard Your Notebook computer features a low-profile keyboard that emulates all the functions of a full-size 101/102 key keyboard including an embedded keypad and a full array of special function keys. This section covers the Notebook’s keyboard, and identifies several keys that are commonly used when working with either the Disk Operating System or other software.
Page 59 3. [Fn]: This key is located in the lower left corner of the keyboard, next to the [Ctrl] key. Pressing this key engages the alternate function (labeled in blue) on selected keys. For example, simultaneously pressing the [Fn] + [F1] keys decreases the display brightness. 4.
Page 60: Cursor Control Keys And Editing Keys
Notebook User’s Guide Cursor Control Keys and Editing Keys The keys listed in this section are specifically used to move the cursor on the LCD Display. When used in combination with other keys, these cursor control keys provide some very powerful editing functions. The cursor’s location indicates where you can type text on the screen.
Page 61: The Function Keys
5. [End]: Refer to your application software manual to find out how to use the End key to quickly move the cursor to the end of a line or to the end of a document. 6. [Insert]: The Insert key is used mainly for editing. It enables you to insert characters within the text while using DOS.
Page 62: Embedded Numeric Keypad
Notebook User’s Guide Embedded Numeric Keypad An embedded numeric keypad consists of 15 keys that make number intensive input more convenient. These keys have both numeric and cursor movement functions, which are labeled in blue on the keycaps. When the numeric keypad is engaged, the Num Lock indicator comes on.
Page 63: Hot Keys For System Control
Hot Keys for System Control The following table lists the hot key functions for the Notebook computer. Key Combinations [Fn] + [Fn] + [Fn] + [PageUp] [Fn] + [PageDn] [Fn] + [F8] [Fn] + [End] [Fn] + [Esc] [Fn] + [A] or [Fn] + [Q] Definitions Increases display brightness...
Page 64: The System Status Indicator Panel
Notebook User’s Guide The System Status Indicator Panel Located above the keyboard, the System Status LED Indicators inform you of the Notebook’s current operating status at a glance. Please see Figure 1-4 to locate this panel. Upon activating a certain function, the LED corresponding to that function will light until you deactivate that feature.
Page 65 Chapter 3: Operation Num Lock Upon pressing the [Scr Lk/Nm Lk] key, this indicator lights indicating the embedded keypad’s numeric feature is activated. Press the [Scr Lk/Nm Lk] key again to deactivate this feature and turn off the indicator. Caps Lock Upon pressing the [Caps Lock] key, indicator lights indicating that the Caps Lock feature is engaged.
Page 66: Definition Tables For The Led Status Indicators
Notebook User’s Guide Definition Tables for the LED Status Indicators The Notebook has six LED indicators. The following tables summarize each of these indicators. Power Indicator The following table describes this status indicator. Color State Green Orange Blinking HDD/FDD/CD-ROM Access Indicator The following table describes this status indicator.
Page 67 Battery Status Indicator The following table describes this status indicator. Color State Meaning Green Blinking Battery is charging from the AC source. Green The battery is fully charged. Green Battery discharging or an abnormal stop charge due to bad cell or over temperature state. Amber Blinking When the indicator is blinking (at a rate of once...
Page 68: Battery Charging Control
Notebook User’s Guide Scroll Lock Indicator The following table describes this status indicator. Color State Green Green Battery Charging Control When the AC Adapter is plugged in, the system automatically begins charging the battery. If an over 60 C temperature condition occurs while charging the battery, the process will be stopped.
Page 69 Please refer to the following for instructions on how to operate the touch pad. 1. Place your fingers on the keyboard in the normal typing position. 2. The touch pad is easily accessible by moving either your left or right thumb off the space bar and on to the touch pad.
Page 70: The Fir Module
Notebook User’s Guide When working with programs that employ a graphical user interface (GUI), such as Windows, dragging objects from one point on the screen to another is a technique you will have to master. To drag an object, first move the pointer over the object, then press and hold down the left button.
Page 71 Follow the guidelines listed below when using the FIR module to transmit or receive data. = Make sure the “Infrared Port” field under the System Devices menu in the BIOS Setup program is enabled and set to an available address. The “MODE”...
Page 72: Multimedia Sound System
Notebook User’s Guide Multimedia Sound System The Notebook Computer’s built-in audio capabilities allow you to take advantage of a wide range of education and entertainment multimedia software available on today’s growing market without the additional costs of add-on cards and peripheral hardware. sophisticated on-board FM sound generator that produces realistic music and human voice sounds in 16-bit stereo.
Page 73 The Notebook’s audio features include: = ESS Maestro-2E digital audio controller (Sound Pro™ and Windows Sound System™ compatible) = 64-channel wavetable synthesizer = Proprietary WaveCache technology = HRTF 3-D positional audio under DirectX™ 5.0 = A sophisticated on-board 16-bit stereo FM sound generator featuring enhanced stereo and full-duplex playback and record with internal playback and record buffer = Sample rate conversion from 8Khz to 48Khz...
Page 74: The Cd-Rom Module
Notebook User’s Guide The CD-ROM Module The CD-ROM provides you with the hardware basics to turn your Notebook computer into a fully functioning multimedia computer. Beyond its audio capabilities, since many software packages are coming out solely on CD-ROM, the addition of this module gives the user more choices in the purchase of software applications.
Page 75: Audio Volume Control
Installing Device Drivers Windows 98 automatically installs and configures plug and play hardware devices including your CD-ROM drive. You do not have to install the driver. If you need to reinstall the driver for some reason, please refer to Chapter 7 of this manual for the driver installation procedure.
Page 76 Notebook User’s Guide...
Page 77: Chapter 4
ERIPHERALS Your Notebook computer is equipped with several ports for connecting a number of peripheral devices such as a printer, a MODEM, or an external monitor. There are also two PCMCIA Card Bus sockets for connecting industry standard PCMCIA Card Bus cards and stereo jacks for connecting external audio equipment.
Page 78: External Monitor
Notebook User’s Guide illustrations in Chapter 1 to identify the following I/O ports. The first seven ports in the following list are located on the rear panel of the Notebook. = One serial port = One parallel port = TV-out port = An external monitor connector = 240-pin docking connector = A USB connector...
Page 79 purchase, you should consult technical support to ensure you have the correct cables. 240-pin Docking Port This port is for the connection of a replicator. A replicator extends the capabilities of the Notebook. The replicator is discussed in Chapter 6 of this manual under the section Optional Equipment.
Page 80 Notebook User’s Guide USB Devices The Notebook is equipped with a Universal Serial Bus (USB) connector. USB devices are PnP compliant as defined by the Universal Serial Bus Specification 1.0. Any device that complies with this standard can be connected to this port. TV Display The Notebook’s video signal can be converted to a standard video signal and displayed on a TV for viewing or recording to video tape.
Page 81: Connecting Peripheral Devices
Connecting Peripheral Devices Connecting an External Monitor Please refer to Figure 4-1 and the following instructions for an external monitor connection: 1. Make sure the Notebook and the monitor are powered off. 2. Ensure that the monitor is the correct type. Do not use a monitor that does not match the VGA standard.
Page 82: Figure 4-2: Connecting A Printer To The Notebook's Parallel Port
Notebook User’s Guide Connecting Parallel Devices To connect a parallel device to the computer you will need the standard parallel 25-pinned connector cable mentioned earlier. Before you connect any device, check the documentation that came with the equipment to see if you need to make any settings or adjustments to the equipment before using it.
Page 83: Figure 4-3: Connecting A Mouse To The Notebook's Serial Port
Chapter 4: Peripherals The Notebook has one Serial Port. Please refer to Figure 4-3. Its address can be set via the BIOS Setup program. Refer to Chapter 2 for information on BIOS Setup. Figure 4-3: Connecting a Mouse to the Notebook’s Serial Port Connecting an External Keyboard The Notebook has a connection for a full-size enhanced 101/102-key keyboard commonly used with desktop computers.
Page 84: Figure 4-4: Connecting An External Keyboard To The Notebook's Ps/2 Port
Notebook User’s Guide To connect a keyboard, perform the following steps: 1. Make sure the computer is turned off. 2. If the keyboard has a PS/2 type connector, plug it into the Notebook’s keyboard connector port. If the keyboard has a PC-type jack, connect it to the adapter cable and then plug the other end of the adapter cable into the computer.
Page 85: Figure 4-5: Inserting And Ejecting A Pcmcia Card
Please refer to Figure 4-5 and the following instructions for inserting and ejecting a PCMCIA card: 1. Some PCMCIA cards do not support hot-plugging. Refer to your PCMCIA card’s manual for verification. If hot-plugging is not supported, save your data and turn off the Notebook before inserting the PCMCIA card. 2.
Page 86 Notebook User’s Guide Zoomed Video Port As part of the Notebook’s advanced architecture, the Zoomed Video port (ZV port) feature provides you with hardware MPEG support. This feature allows you to insert a ZV Port-compliant MPEG PC Card into one of the Notebook’s PCMCIA expansion sockets.
Page 87: Figure 4-6: Connecting A Usb Device
Chapter 4: Peripherals Connecting a USB Device The Notebook is equipped with a Universal Serial Bus (USB) connector. The USB connector and its supporting circuitry were designed in full compliance with the Universal Serial Bus Specification 1.0. Any device that uses this standard can be connected to this port.
Page 88 Notebook User’s Guide Connecting a Phone Line to the RJ-11 MODEM Port To use the Notebook’s MODEM you must first connect a phone line to the RJ- 11 connector. The Fax/MODEM port is located on the left side of the Notebook (see Figure 1-2).
Page 89: Chapter 5
HAPTER OWER YSTEM This chapter contains information on the Notebook’s power system, including the AC Adapter, the battery system, recharging the battery, and tips for conserving battery power. Also included is a detailed description of power management and each of the power modes. The power system is comprised of two parts, the AC Adapter and the battery system.
Page 90: The Ac Adapter
Notebook User’s Guide The AC Adapter The AC Adapter’s primary function is to provide power to the computer. Refer to Chapter 1 for instructions on how to connect the AC Adapter to the computer. When the Adapter is connected to the computer, it provides power as long as it is plugged into an electrical outlet.
Page 91: The Battery Power System
The Battery Power System The Notebook’s removable battery pack is found in the battery compartment bay. Please see Figure 1-1 if you are having trouble locating this bay. A fully charged pack will provide approximately 3 hours of battery life for an Li-Ion battery before you have to recharge or replace the battery.
Page 92 Notebook User’s Guide A safety feature automatically stops the charging process after the battery has reached its full charging capacity. This prevents dangerous conditions from occurring if there is a fault somewhere in the charging circuitry. There is another built-in protector preventing the battery from over charging by using a temperature parameter.
Page 93: Removing The Battery Pack
Removing the Battery Pack To remove the battery pack from its housing, refer to Figure 5-3 and the following instructions: 1. Turn off the Notebook’s power. Never remove a battery module while the Notebook is on. 2. Close the Notebook’s cover, ensuring that it snaps into place. Turn the Notebook so the bottom is facing you.
Page 94: Inserting The Battery Pack
Notebook User’s Guide Inserting the Battery Pack To insert the battery pack into the Notebook, refer to Figure 5-4 and the following instructions: 1. Slide the battery into the battery bay as shown in Figure 5-4. 2. When the battery has been properly seated, you should hear it click into place.
Page 95: Automatic Battery Pack Charging Function
Chapter 5: The Power System Automatic Battery Pack Charging Function When running the Notebook on AC power, the inserted battery pack will automatically be recharged while you are working on your Notebook. There are two charge speeds. When the computer is turned off or in Suspend mode, the charge time is about 2 hours.
Page 96: Ac Power Connection
Notebook User’s Guide AC Power Connection The Notebook can be powered by AC current by connecting the AC Adapter to the external AC port on the Notebook. When the Notebook is operating on AC power, the battery or batteries installed in the Notebook will be charged simultaneously.
Page 97: Using Battery Power
Using Battery Power The battery system will provide approximately 3 hours of power to the Notebook when Power Management is disabled. depending on how you use the power saving features, your general work habits, and the type of CPU and LCD that your Notebook has. We recommend you use the AC Adapter as often as possible to conserve battery power.
Page 98: Low Battery Activity
Notebook User’s Guide Low Battery Activity When the battery has entered the critical battery state, the system will begin to beep, prompting you to save your data. Failure to save at this time may result in data loss. To extend battery power, we recommend you make full use of the Notebook’s built-in power saving features discussed later in this chapter.
Page 99 The Suspend/Resume Feature The Suspend/Resume is one of the Notebook’s most useful non-automatic features. If you need to temporarily step away from the computer, simply press one of the two hot key combinations to put the computer into its maximum power saving mode while maintaining your work.
Page 100: Power Management Modes
Notebook User’s Guide Power Management Modes The computer has a number of automatic or adjustable power conservation features, which you can use to maximize the duration of the battery’s life. You can control many of these features through the Power Menu in the Setup (BIOS) program.
Page 101 The PHDISK Utility In order to use the Save to Disk function you must first create a Save to Disk (STD) partition or file on the Notebook’s hard disk. The PHDISK utility is used to create this partition. During the Save to Disk operation, the system’s state is written to this STD partition.
Page 102 Notebook User’s Guide Select the Hibernate tab and click the Hibernate option box to enable hibernate support. The default is disabled. Now click the Apply button at the bottom right of the window. Select the Advanced tab to change the Power buttons settings. Available options are: Lid switch settings: None...
Page 103 time-out is set to 2 minutes, and the Suspend time-out is set to 5 minutes, then the following power management events take place: 1. After 2 minutes of inactivity, the system enters Standby. 2. After 5 additional minutes in Standby (a total of 7 minutes of inactivity), the system Suspends to RAM or Saves to Disk, depending upon the settings made in the Power Menu of the BIOS Setup program.
Page 104: Controllable Features
Notebook User’s Guide How to Resume Pressing the Power On/Off button causes the system to resume operation after entering Suspend mode. Resuming returns the system’s operation to the point in your application where the suspend was initiated. This does not mean, however, that all devices are powered up.
Page 105: Cover Lid Switch
Cover Lid Switch The Notebook’s LCD Cover Lid Switch is located above the keyboard. See Figure 1-4. If the Notebook is powered on and the lid is closed, the LCD panel will power off and the display will be switched to the CRT monitor connected to the VGA port.
Page 106: Power Management Summary
Notebook User’s Guide Power Management Summary The following table summarizes the power-saving features of the Notebook: Power Mode How to Enter Mode Standby Transits automatically after specified time-out Suspend to Transits automatically after specified time-out Cover is closed Click on the Suspend icon in the Windows Start menu Save to Transits automatically after...
Page 107: The Apm Interface
The APM Interface In addition to the power saving features built into the resident BIOS System Configuration Utility, your Notebook also supports the Intel-Microsoft Advanced Power Management (APM) version 1.2 (or higher) specification. APM is a cooperative interface that enhances the Notebook’s built-in power management features by providing one of the most accurate schemes for detecting true idle.
Page 108: The Advanced Configuration And Power Interface (Acpi)
Notebook User’s Guide The Advanced Configuration and Power Interface (ACPI) In addition to APM 1.2 the Notebook also supports ACPI power management modes. ACPI is a configuration and power management mechanism that has evolved from, and is therefore inclusive of, the existing collection of power management codes such as APM and PnP BIOS.
Page 109: Chapter 6
XPANSION PTIONS This chapter describes the optional equipment that can be added to the basic Notebook system. We use the term expansion here to signify items that are installed inside the computer rather than standard equipment such as a printer that can be connected to the computer’s I/O ports.
Page 110: Removing And Installing Modules
Notebook User’s Guide 1. The memory door is located on the underside of the Notebook. Remove the two screws securing the door and lift it clear to reveal the two memory DIMM (Dual Inline Memory Module) slots. Figure 6-1: Removing the Memory Door and Installing the Memory Card 2.
Page 111: Figure 6-2: Removing The Cd-Rom Module
All modules are installed in the Notebook’s middle bay. The battery pack is in bay on the left. Before you install any of the optional modules, you must remove the CD-ROM Module from the bay. The procedure for removing the CD-ROM Module or removing any of the modules from the bay is essentially the same.
Page 112: Figure 6-3: Installing The Cd-Rom Module
Notebook User’s Guide 6. Install the desired module by inserting it back into the bay. Please refer to Figure 6-3. When the module has been properly seated, you should hear it click into place. The release latch is spring-loaded and will snap back into place.
Page 113: Replacing The Battery Module
Replacing the Battery Module The optional battery module allows for extended battery power when you are on the road. The Notebook’s battery module will run out of power after approximately 2-3 hours of use. An extra battery module allows you more flexibility when you’re away from the office, adding an additional 2-3 hours to the computer’s operational time.
Page 114: Figure 6-5: Removing The Hdd Module (B)
Notebook User’s Guide Figure 6-5: Removing the HDD Module (B) To install a new HDD module, follow the above instructions in the reverse order and refer to Figure 6-6. Figure 6-6: Replacing the HDD Module...
Page 115 Chapter 6: Expansion Options Figure 6-7: : Replacing the HDD Module...
Page 116: Removing And Installing The Fdd Module
Notebook User’s Guide Removing and Installing the FDD Module To remove and install the FDD module, please refer to Figure 6-7, Figure 6-8, and the following directions. Turn off the Notebook and disconnect the AC power cord and any connected peripherals. The FDD retaining screws are located on the underside of the Notebook.
Page 117: Figure 6-8: Removing The Fdd Module (B)
Remove the two screws holding the keyboard in place. Now gently lift the keyboard, placing it down on the touch pad as shown in Figure 6-8. Take care that you don’t damage the ribbon cable attached to the keyboard. With firm even pressure, slide the FDD in the direction indicated by the arrow as shown in the illustration;...
Page 118: Removing And Installing A Mini Pci Card
Notebook User’s Guide Removing and Installing a Mini PCI Card You may find it helpful to refer to Figure 6-9 while reading the following directions. 1. Turn off the Notebook and disconnect the AC power cord, any connected peripherals and the telephone wire. 2.
Page 119: The I/O Port Replicator
Chapter 6: Expansion Options The I/O Port Replicator The I/O Port Replicator features the most innovative advances in Notebook personal computing technology. Much consideration has gone into the design of the I/O Port Replicator in order to meet your requirements for versatility as well as quality.
Page 120: The Ac Adapter And Peripherals Connection
Notebook User’s Guide The AC Adapter and Peripherals Connection The AC Adapter port and all peripheral ports are located on the rear side of the I/O Replicator. Please see Figure 6-10 for a complete port layout. You will want to place the I/O Port Replicator flat on a desk near a wall outlet or an extension cord with a built-in circuit breaker.
Page 121: Figure 6-11: Connecting The Notebook To The I/O Port Replicator
To connect your Notebook to the Port Replicator observe the following steps: 1. Prepare the Port Replicator by connecting the desired peripheral devices and connecting the Port Replicator to an AC power source. 2. If no peripheral devices are connected to the Notebook, there is no need to turn off the system since it can be warm-plugged into the Port Replicator.
Page 122: Removing The Notebook From The I/O Port Replicator
Notebook User’s Guide Removing the Notebook from the I/O Port Replicator Refer to the following illustration and instructions to remove the Notebook from the Port Replicator. 1. Save your data and enter your Notebook into the Suspend mode. 2. Pull both release levers in the direction of the arrows as illustrated in Figure 6-12.
Page 123: I/O Replicator Specifications
I/O Replicator Specifications External Interfaces = One PC/AT compatible parallel port = One PC/AT compatible RS232C serial ports = One external VGA monitor connector = One external keyboard connector for PC/AT compatible keyboard = One external PS2 mouse connector = Three audio connectors (Microphone, Headphone-out, Line-in) = One USB connector (two slots) = TV out connector = LAN port...
Page 124 Notebook User’s Guide...
Page 125: Chapter 7
OFTWARE Driver Installation This chapter covers the installation of device drivers in the Windows 98 Second Edition environment. The step-by-step instructions provided in this chapter will help you install and configure the drivers for your VGA adapter, audio chip, the modem and the touch pad. HAPTER...
Page 126: Vga Driver Installation
Notebook User’s Guide VGA Driver Installation Insert the Support Disc (CD) into the CD-ROM drive. Click the Start button; then select run. Use Browse to locate: E:\Win98\Video_Driver\Setup.exe Now click OK. The ATI device driver will be automatically installed by the system and the following screen should appear. Make sure that the “Yes, I want to restart my computer now.”...
Page 127: Audio Driver Installation
Audio Driver Installation Insert the Support Disc (CD) into the CD-ROM drive. Hold down the Windows key and press [Pause] to open the System Properties window. Select the Device Manager tab. Chapter 7: Software...
Page 128 Notebook User’s Guide Remove PCI Multimedia Audio Device in Other Devices. Click Refresh. The following screen will appear: Now click Next>. The following screen will appear:...
Page 129 Make sure that the “Search for the best driver for your device.” radial button is selected and click Next>. Select Specify a location: and use Browse to select the Audio Driver on the Support Disc CD as indicated in the illustration above. Click Next>. Make sure that the “The updated driver [Recommended] ESS Device Manager”...
Page 130 Notebook User’s Guide 10. Now click Next>. The Audio Driver will be installed. 11. Click Finish to complete the Audio Driver installation.
Page 131: Mini Pci Modem Driver Installation
Mini PCI Modem Driver Installation Insert the Support Disc (CD) into the CD-ROM drive. Hold down the Windows key and press [Pause] to open the System Properties window. Select the Device Manager tab. The Mini PCI Modem Card must be installed before installing the modem device driver.
Page 132 Notebook User’s Guide Remove PCI Communication Device in Other Devices. Click Refresh. The following screen will appear: Click Next>. The following screen will appear: Make sure that the “Search for the best driver for your device.” radial button is selected and click Next>.
Page 133 Select Specify a location: and use Browse to select the Mini PC Modem Driver on the Support Disc CD as indicated in the illustration above. Click Next>. Now click Next>. The Mini PCI Modem Driver will be installed. Chapter 7: Software...
Page 134 Notebook User’s Guide 10. Click Finish to complete the Mini PCI Modem Driver installation.
Page 135: Touch Pad Driver Installation
Touch Pad Driver Installation Click Start, then Run. Insert the Support Disk (CD) into the CD-ROM drive. Click the Browse button to find the touch pad driver and click OK. Files will be extracted and the Welcome screen will appear. Click Next >. Chapter 7: Software...
Page 136 Notebook User’s Guide Click Next >. Click Next >. Files will be copied to your hard drive.
Page 137 Select the radio button next to Yes, I want to restart my computer now. and click Finish to complete the installation. When your computer reboots, you will see the following screen. The installation procedure is complete. For more information on the Synaptics touch pad, click the Tell me more button.
Page 138 Notebook User’s Guide Creating the Save-To-Disk Suspend Partition or File In order to use the save-to-disk function you must first create a save to disk partition or file on the Notebook’s hard disk. The PHDISK utility is used to create this partition or file. During the save to disk operation, the system’s state is written to this save-to-disk partition or file.
Page 139 If you have installed a new Operating System on the hard drive without the save to disk partition, use the PHDISK utility to create a save-to-disk suspend file. When save-to-disk suspend mode is activated, all system data is stored in this file.
Page 140 Notebook User’s Guide...
Page 141: Chapter 8
ARING FOR YOUR General Maintenance The best maintenance you can perform yourself is preventive. Try to keep the computer as clean as possible. Avoid transporting or using it in dirty or dusty environments if possible. Use the carrying bag provided or some other clean container when you transport the computer.
Page 142: Cleaning The Computer
Notebook User’s Guide Cleaning the Computer Cleaning the Case If the computer case becomes soiled, you can clean it. Always make sure that the computer is turned off and the AC adapter is disconnected before cleaning the computer. You can clean the case with a soft, preferably lint-free, cloth. If necessary, you can use a mild detergent.
Page 143 Cleaning the Diskette Drive In order to avoid causing damage to the sensitive read/write heads and diskette surface, it is important to prevent dust particles and dirt from entering the disk drive slot. If you suspect that the floppy disk drive needs cleaning, you can purchase a disk drive cleaning kit from your computer dealer.
Page 144: Caring For Diskettes
Notebook User’s Guide Caring for Diskettes Under normal conditions, a diskette’s rigid plastic case will protect it from damage. However, data stored on floppy diskettes are easily corrupted. Follow the protective measures listed below to preserve the integrity of data stored on floppy diskettes.
Page 145: Safety Precautions
Safety Precautions Follow these steps and you will increase the working lifetime of your Notebook. You will also reduce the chance of damage to your computer and personal injury to yourself. = Follow all cautions and instructions that may be marked on the Notebook. = Except as described elsewhere in this manual, refer all servicing to qualified personnel.
Page 146 Notebook User’s Guide...
Page 147: Troubleshooting
PPENDIX ROUBLESHOOTING Your Notebook has passed through a series of rigorous quality assurance tests to guarantee reliable performance. However, a computer is a sophisticated piece of equipment and as such may malfunction if used incorrectly or if one of its components fails. This chapter will try to anticipate potential problems that you may encounter in the day-to-day use of your computer.
Page 148: An Approach To Troubleshooting
Notebook User’s Guide An Approach to Troubleshooting In general, troubleshooting involves an organized system of approach to problem solving. Try to isolate the problem and identify the defective device (hardware) or improper setting (software). When you have a problem, you should do a thorough visual inspection of the Notebook.
Page 149 Booting Up Question: When I turn the Notebook on, I can’t get an operating system prompt to appear on the screen. The Notebook does seem to be running, though. Answer: Make sure that you have properly installed an operating system on the hard disk.
Page 150: I/O Connections
Notebook User’s Guide I/O Connections External Monitor Question: Is it possible to use both an external and the LCD screen at the same time? Answer: Yes, the Notebook provides three display configurations: LCD, monitor, and Simul Scan (LCD & MONITOR active at the same time). The three modes are toggled on and off by pressing [Fn] + [F8].

Sceptre S6900 User Manual

Chapter 1

Introducing the Notebook

Chapter 2

The BIOS Setup Program

Chapter 3

Operation

Chapter 4

Peripherals

Chapter 5

The Power System

Chapter 6

Expansion Options

Chapter 7

Software

Chapter 8

Caring for Your Notebook

Appendix A Troubleshooting

Quick Links

Troubleshooting

Related Manuals for Sceptre S6900

Summary of Contents for Sceptre S6900

Table of Contents