Page 1 December 1998 The information in this document is subject to change without notice and should not be construed as a commitment by the manufacturer. The manufacturer assumes no responsibility for any errors that might appear in this document. The software described in this document is furnished under a license and may be used or copied only in accordance with the terms of such license.
Page 2 The FCC wants you to know... This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Page 3 Federal Communications Commission (FCC) PART 68 Warning This equipment complies with Part 68 of the FCC Rules. On the bottom of the computer is a label that contains, among other information, Registration Number and Ringer Equivalence Number (REN) for this equipment.
Page 4: Canadian Doc Notice
CANADIAN DOC NOTICE This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the Radio Interference Regulation of the Canadian Department of Communications. "Le présent appareil numérique n’èmet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de la class B prescrites dans le Règlement sur le brouillage radioélectrique édicté...
Page 5: Table Of Contents
Table of Contents Chapter 1 ... 1 Introducing the Notebook... 1 Features and Controls ... 2 Optional Devices ... 7 Unpacking & Checking the Equipment... 7 Identifying Parts of the Notebook... 8 Installation and Initial Setup ... 14 Chapter 2 ... 19 The BIOS Setup Program...
Page 6 The FIR Module ... 55 Multimedia Sound System ... 56 Audio Volume Control ... 57 Chapter 4 ... 59 Peripherals ... 59 Additional Equipment... 60 Connecting Peripheral Devices... 62 Chapter 5 ... 69 The Power System ... 69 The AC Adapter ...
Page 7 Optional Modules ... 89 Removing and Installing HDD Modules... 90 The I/O Port Replicator ... 93 The AC Adapter and Peripherals Connection... 94 The Notebook to I/O Port Replicator Connection ... 94 Removing the Notebook from the I/O Port Replicator ... 95 I/O Replicator Specifications...
Page 8 Abbreviations Abbreviation Meaning ACPI Advanced Configuration and Power Interface Advanced Power Management (This Notebook supports APM 1.2) Basic Input/Output System BIOS CMOS Complementary Metal Oxide Semi-conductor DIMM Dual In-line Memory Module Direct Memory Access Dynamic Random Access Memory DRAM Digital Versatile Disc EDO RAM Extended Data Out Random Access Memory Integrated Drive Electronics (internal hard disk drive interface)
Page 9 ABOUT THIS GUIDE This guide describes how to operate, configure, and troubleshoot the Note- book computer. With this easy to use guide, you will be able to quickly familiarize yourself with all aspects of the Notebook computer. Organization This guide contains the following: Chapter 1: Introducing the Notebook - This chapter identifies the external components of the Notebook and provides a quick reference to the Notebook functions.
Page 10: Special Notices
Chapter 7: Caring for Your Notebook - This chapter covers some of the basic maintenance procedures you may want to familiarize yourself with. introduces proper methods of cleaning the case, the screen, the FDD drive, as well as some helpful tips on handling diskettes. Appendix A: Troubleshooting - In a question and answer format, this section provides you with solutions to possible problems that may arise.
Page 11: Chapter 1
HAPTER NTRODUCING THE OTEBOOK Your new Notebook features the most innovative advances in portable computing technology. It combines state-of-the-art ergonomics with sophisticated architecture to provide you with a personal computer that is compact, powerful, and easy to use. The modular design of the Notebook provides maximum expandability without compromising portability.
Page 12: Features And Controls
Notebook User’s Guide Features and Controls This section provides an overview of the Notebook’s features. For more detailed information see the Specifications section in Appendix B. Your Notebook includes the following features: The microprocessor (CPU) is the heart and brain of the computer. It performs all the computing functions and orchestrates the actions of the system.
Page 13 LCD VGA Display Your Notebook’s VGA display is with a 1024 x 768 XGA resolution back-light display. VGA Graphics Accelerator and Video Subsystem This Notebook is equipped with an ATI 3D Rage LT PRO VGA AGP controller chip offering the following features: = Supports AGP Bus (a clock-doubling technique boosts speed to 133MHz) = Supports simultaneous LCD and CRT displays, and simultaneous LCD and TV displays...
Page 14 Notebook User’s Guide Windows 95/98 Enhanced Keyboard The keyboard supports Windows 95/98 by incorporating two Windows specific keys. With these keys you will be able to access and take advantage of many of the time-saving features offered by Windows 95/98. The Touch Pad The Notebook features a Touch Pad pointing device with two buttons.
Page 15: Chapter 1: Introducing The Notebook
= One 4-pin Universal Serial Bus (USB) connector = One TV-Out (S-type) port = RJ-11 MODEM port (optional) = PCI Bus connector MPEGII card (optional) PCMCIA Sockets An ACPI-compliant PCMCIA R2.0 host adapter supports one type III PCMCIA card or two type II PCMCIA cards. The PCMCIA sockets support hot insertion and removal and can accommodate SRAM, OTPROM, FLASHROM and Mask ROM memory cards of up to 64MB, MODEM/LAN cards and 10.5mm removable HDD.
Page 16 Notebook User’s Guide control the sound volume. A complete list of the Notebook’s hot key functions is provided in Chapter 3. Power Management The Notebook features sophisticated power management built into the BIOS Setup program. These features are designed to conserve power and extend the life of the battery between charges.
Page 17: Optional Devices
Optional Devices There are several optional products you can purchase to further enhance the utility and versatility of your Notebook computer. = HDD Module = Combo Module: FDD/CD-ROM or FDD/DVD = LS-120 Module = 56K V.34 Fax/MODEM = I/O Port Replicator = MPEG II Card = Car Adapter = Extra memory modules (32, 64, 128MB 144-pin 3.3V SODIMM)
Page 18: Identifying Parts Of The Notebook
Notebook User’s Guide Identifying Parts of the Notebook The illustrations that follow identify the various features and external components of the Notebook computer. Familiarizing yourself with these terms will help you as you read the rest of the manual. Right Front View (Panel Closed) Figure 1-1: Right Front View with Display Panel Closed 1.
Page 19 Power Indicator This LED will light when the Notebook is powered on. Refer to Chapter 3, LED Status Indicators for more information on the Power Indicator. HDD Indicator This LED will light when the hard disk is being accessed. Battery Indicator This LED will blink when the battery is charging.
Page 20 Notebook User’s Guide Left Front View (Panel Closed) Figure 1-2: Left Front View with Display Panel Closed 1. AC Power Jack Connect the AC Adapter power cord to this jack. 2. PCMCIA sockets Insert PCMCIA Type I, Type II, or Type III cards into these sockets. Audio Line-in Connector This stereo jack is used to connect an external audio source to the Notebook.
Page 21 Internal Stereo Speaker See Figure 1-1 for a description of the internal stereo speakers. The Audio jacks are three-terminal stereo jacks but are used as two terminal mono jacks. compatible with two-terminal mono plugs. Rear View The rear side of the Notebook contains an FIR (fast infrared) port, a serial (COM) port, a Parallel (LPT1) port, a VGA port, a PS/2 mouse/external keyboard port, a USB port, TV out port, and a 240-pin I/O Docking connector.
Page 22 Notebook User’s Guide 6. Universal Serial Bus (USB) Port Connect any USB compliant device to this port. 7. External Keyboard or PS/2 Mouse Port This port is for connecting either an external keyboard or a PS/2 mouse. 8. FIR Port The FIR Module allows wireless communication (transmission and receiving) between the Notebook and another FIR-equipped computer or between the Notebook and another FIR-equipped device, such as a printer.
Page 23 1. LCD Screen The screen is a color TFT LCD. Suspend/Resume Lid Switch There are three ways to enter the system into Suspend mode. One is to automatically enter Suspend mode. The system will enter Suspend mode based upon the settings made in the Basic Input Output System (BIOS) Setup program.
Page 24: Installation And Initial Setup
Notebook User’s Guide Installation and Initial Setup If you are unfamiliar with computers, this section guides you through turning on your Notebook for the first time. This section also explains what you need to do after turning on your Notebook. Experienced computer users may need only read this section while using the rest of the manual merely as a reference.
Page 25 4. Plug the Notebook into its power source and press the On/Off button. If the Notebook does not power up, check the connections between the wall outlet, the AC Adapter, and the Notebook. If the Notebook still does not power up, please refer to Appendix A, Troubleshooting. 5.
Page 26 Notebook User’s Guide In most cases, the record should be correct when you receive the computer. If so, the POST will finish and the computer will look for an Operating System to load into memory. The self test will run every time you turn on the computer. When the test is finished, you should get a message indicating that there is a non-system disk or disk error.
Page 27 occupational safety are involved in the study of ergonomically sound work environments. If your budget permits, buy ergonomically designed furniture such as chairs, shelves, and desks that fit your physical characteristics and work methods. Most furniture manufacturers have not considered the particular shape of your body when designing workstations.
Page 28 Notebook User’s Guide...
Page 29: Chapter 2
BIOS S ETUP Introduction The BIOS (Basic Input and Output System) Setup program is a menu driven utility that enables you to make changes to the system configuration and tailor the operation of your Notebook to your individual work needs. A ROM-based configuration utility displays the system’s configuration status and provides you with a tool to set system parameters.
Page 30: Navigating Through The Bios Setup Program
Notebook User’s Guide Navigating through the BIOS Setup Program The Setup program has been designed to make it as easy to use as possible. It is a menu driven program, which means you can scroll through the various directories and make your selections among the various predetermined choices. If you accidentally make a setting and do not know which one to switch back to, use the BIOS hot keys to return to the previous value.
Page 31 Accessing the BIOS Setup Program To access the BIOS Setup program, press the F2 key after the Notebook has run through its POST. The Menu Bar The top of the Setup screen has a menu bar with the following selections: Main Use this menu to make changes to the basic system con- figuration.
Page 32 Notebook User’s Guide Legend Key [F1] or [Alt] + [H] [Esc] [!] or ["] [-] or [$] [Tab] [Shift]+[Tab] [F5] [F6] [F9] [F10] [Enter] Launching Submenus A submenu contains additional options for a field parameter. To call up a submenu, simply move the highlight to the desired field and press the [Enter] key.
Page 33 General Help In addition to the Item Specific Help window, the BIOS Setup program also provides a General Help screen. This screen can be called up from any menu by simply pressing the function key [F1], or the [Alt] + [H] combination. The General Help screen lists the legend keys with their corresponding alternates and functions.
Page 34: The Main Menu
Notebook User’s Guide The Main Menu When the Setup program is accessed, the following screen appears: Main System Devices Figure 2-1: The Setup Main Menu Enter the Main Menu of the BIOS setup program to make changes to the Notebook’s basic system configuration. Each of the fields displayed in this menu is covered below in detail.
Page 35: Quiet Boot
Hard Disk The number value in this field indicates the size of your Notebook’s hard drive. The system will automatically detect the size of your hard drive. You do not need to make changes to this field. This is a display only field. Quiet Boot This field allows you to display the diagnostic screen during bootup.
Page 36: The System Devices Menu
Notebook User’s Guide Television Type This field allows you to choose the television type when connecting the Notebook to a TV. The possible settings are: = NTSC = PAL The default value for this field is: NTSC System Memory This field displays the amount of conventional memory detected by the system during bootup.
Page 37 When the MODEM appears. You need to use the arrow [$] key to access the rest of the fields. This menu allows you to configure the Notebook’s IDE and FDD controllers, serial and parallel ports, as well as, IR (infrared) and Audio modes. Each field on this menu is covered below.
Page 38 Notebook User’s Guide Serial Port This field allows you to configure the Notebook’s serial port. The following options are available: = Disabled = Enabled = Auto The default value for this field is: Enabled Base I/O Address When the Serial Port field is set to Enabled, the “Base I/O Address” field becomes available and you can set the serial port’s IRQ and I/O address.
Page 39 Base I/O address Use this option to choose the I/O (port) address for the Infrared port. The available options are: = 3F8, IRQ 4 = 2F8, IRQ 3 = 3E8, IRQ 4 = 2E8, IRQ 3 This field is only available when the Infrared port is set to Enabled. The default value is: 2F8, IRQ3 DMA Channel (Only Available for Fast IR Mode) This field allows you to configure the Infrared port’s DMA Channel.
Page 40 Notebook User’s Guide Mode This field allows you to configure the Notebook’s parallel port transmission mode. The following options are available: = Normal Mode = Bi-directional = ECP = EPP Normal mode allows data output only. However, EPP and ECP are Bi- directional modes, allowing both data input and output.
Page 41 This field is only available when the Parallel Port Mode field is set to ECP. The default value for this field is: DMA 3 MODEM Port (Only Available if a This field allows you to configure the are available: = Disabled = Enabled = Auto The default value for this field is: Disabled...
Page 42: The Security Menu
Notebook User’s Guide = DMA 5 = DMA 6 = DMA 7 This field is only available when the Enabled. The default value for this field is: DMA 6 16-bit DMA Channel B This field allows you to configure the voice device.
Page 43 Each field of the Security Menu is covered in detail below. A Note about Passwords The BIOS Setup program allows you to specify passwords in the Security menu. The passwords control access to the BIOS and certain Security menu options during system startup. The passwords are not case sensitive. In other words, a password can be entered using either upper or lower case letters;...
Page 44: Password On Boot
Notebook User’s Guide press the [Enter] key twice. The password is now cleared and the “System Password is” field is automatically set to Clear. When changing or clearing the password a “Setup Notice” will inform you that changes have been saved. Press the [Enter] key to register your changes. Password On Boot When enabled, the system will then require the password before the system can bootup.
Page 45 Power Management Mode This menu item allows you to set power management features with pre-defined values. The available options for this field are: = Disabled = Customized = Max. Power Savings = Max. Performance If this menu item is set to Disabled, power management features will not function regardless of other field settings on this menu.
Page 46: Suspend Time-Out
Notebook User’s Guide = 1 Minutes = 2 Minutes = 4 Minutes = 6 Minutes = 8 Minutes = 12 Minutes = 16 Minutes This field can only be set when the “Power Management Mode” field is set to Customized. The default value for this field is: Disabled Suspend Time-out This field determines the amount of time the system needs to be in Standby mode before entering the Suspend to RAM mode.
Page 47: Resume Time
Resume On MODEM Ring When this field is set Enabled, a resume from Suspend mode. = Disabled = Enabled The default value for this field is: Disabled Resume On Time of Day This option allows you to enable the system to resume at a specific time. The possible options are: = Disabled = Enabled...
Page 48: The Boot Menu
Notebook User’s Guide The Boot Menu The Boot Menu allows the user to specify the order in which the Notebook is to check for a device to boot the system. To make changes, select Boot from the menu bar. The following screen appears: Figure 2-5: The Boot Menu Boot Sequence The Boot Menu allows you to use the up and down arrow keys to select among...
Page 49: The Exit Menu
The Exit Menu Once you have made all of your selections from the various menus in the Setup program, you should save your changes and exit Setup. Select Exit from the menu bar to display the following menu: System Devices Main Figure 2-6: The Exit Menu Each of the options on this menu is described below.
Page 50 Notebook User’s Guide Setup Confirmation Save configuration changes and exit now? [Yes] The next time you bootup the Notebook, the BIOS will attempt to load the values you saved in Non-Volatile memory. If these values cause the system boot to fail, reboot and press [F2] to enter the Setup program. Once in Setup, you can try to change the values that caused the system boot to fail.
Page 51 Load Previous Values This option allows you to discard the selections you have made and restore the values you previously saved. After selecting this option, all selections are updated, and the following message is displayed: Setup Confirmation Load previous configuration now? [Yes] [No] Save Changes...
Page 52 Notebook User’s Guide...
Page 53: Chapter 3
PERATION Introduction This chapter provides information pertaining to the Video Display Controls of the Notebook used to adjust the appearance of the LCD screen. Also included in this chapter is a brief overview of the keyboard, how the System Window indicator symbols help you to diagnose or determine any of the specific computer activities going on at a given time, and a description of the Touch Pad, FIR module, and the Notebook’s audio features.
Page 54: Some Important Keys On The Keyboard
Notebook User’s Guide Some Important Keys on the Keyboard Your Notebook computer features a low-profile keyboard that emulates all the functions of a full-size 101/102 key keyboard including an embedded keypad and a full array of special function keys. This section covers the Notebook’s keyboard, and identifies several keys that are commonly used when working with either the Disk Operating System or other software.
Page 55 the [Ctrl] key. Pressing this key engages the alternate function (labeled in blue) on selected keys. For example, simultaneously pressing the [Fn] + [F1] keys decreases the display brightness. 4. [PrtSc/SysRq]: Pressing this key will cause whatever is on the screen at the time to be printed.
Page 56: Cursor Control Keys And Editing Keys
Notebook User’s Guide Cursor Control Keys and Editing Keys The keys listed in this section are specifically used to move the cursor on the LCD Display. When used in combination with other keys, these cursor control keys provide some very powerful editing functions. The cursor’s location indicates where you can type text on the screen.
Page 57: The Function Keys
5. [End]: Refer to your application software manual to find out how to use the End key to quickly move the cursor to the end of a line or to the end of a document. 6. [Insert]: The Insert key is used mainly for editing. It enables you to insert characters within the text while using DOS.
Page 58: Hot Keys For System Control
Notebook User’s Guide Figure 3-3: The Embedded Numeric Keypad Hot Keys for System Control The following table lists the hot key functions for the Notebook computer. Key Combinations [Fn] + [#] [Fn] + [$] [Fn] + [F1] [Fn] + [F2] [Fn] + [F3] [Fn] + [F4] [Fn] + [F5]...
Page 59: The System Status Window
Chapter 3: Operation The System Status Window Located above the keyboard, the System Status window informs you of the Notebook’s current operating status at a glance. Please see Figure 1-4 to locate this display. Upon activating a certain function, a symbol or icon corresponding to that function will appear in the system window until you deactivate that feature.
Page 60 Notebook User’s Guide icon appears in the System Status window, the embedded keypad will be active. Scroll Lock Upon pressing the [Fn] + [Scr Lk/Nm Lk] key, this icon appears in the System Status window indicating the scroll lock is engaged. Press the [Fn] + [Scr Lk/Nm Lk] key again to deactivate this feature and turn off the icon.
Page 61: Led Status Indicators
approximately 90% battery life is remaining. When there is only one vertical line, approximately 10% battery life is remaining; this is referred to as the low battery state. At this time, there will be approximately 10-20 minutes of battery power left. When there are no vertical lines showing, the battery has entered the critically low state.
Page 62: Battery Charge Indicator
Notebook User’s Guide Color State Green Green Amber Amber HDD/FDD/CD-ROM/PCMCIA Access Indicator The following table describes this status indicator. Color State Green Green Battery Charge Indicator The following table describes this status indicator. Color State Green Green Flashing Green Meaning The Notebook’s power is on.
Page 63: Battery Charging Control
Battery Charging Control When the AC Adapter is plugged in, the main battery will always be the first to receive a charge. After the main battery is charged to capacity, the secondary battery will then be charged, assuming it is installed. If the Notebook is not being charged by AC power, the secondary battery, assuming one is installed, will be the first battery to be discharged.
Page 64 Notebook User’s Guide Please refer to the following for instructions on how to operate the Touch Pad. 1. Place your fingers on the keyboard in the normal typing position. 2. The Touch Pad is easily accessible by moving either your left or right thumb off the space bar and on to the Touch Pad.
Page 65: The Fir Module
releasing the button, move the object to a new location on the screen by moving your finger across the Touch Pad. Once the object is in the desired position, release the button to drop the object in place. The FIR Module The Notebook is equipped with two FIR modules located on the rear and front panels.
Page 66: Multimedia Sound System
Notebook User’s Guide otherwise, the optical signal will be blocked. anything between the two FIR modules during data transmission. = Do not move either the Notebook or the other device during transmission of data. Moving either the Notebook or the other device during transmission distorts the optical signal resulting in loss of data or a system crash.
Page 67: Audio Volume Control
= A sophisticated on-board 16-bit stereo FM sound generator featuring enhanced stereo and full-duplex playback and record with internal playback and record buffer = 64-Voice Wavetable Synthesizer = Secondary CODEC Interface = AC-3 Speaker Virtualization = Two integrated speakers and an internal microphone = Stereo inputs for Line-in, CD-ROM and music synthesis and a mono input for the microphone = Enhanced Digital Game Port...
Page 68 Notebook User’s Guide This concludes Chapter 3. The next chapter covers attaching peripherals such as a printer or an external monitor.
Page 69: Chapter 4
ERIPHERALS Your Notebook computer is equipped with several ports for connecting a number of peripheral devices such as a printer, a MODEM, or an external monitor. There are also two PCMCIA Card Bus sockets for connecting industry standard PCMCIA Card Bus cards and stereo jacks for connecting external audio equipment.
Page 70: Additional Equipment
Notebook User’s Guide Additional Equipment Before attempting to connect a peripheral device to the computer, make sure you are familiar with the Notebook’s various I/O ports. illustrations in Chapter 1 to identify the following I/O ports. The first six ports in the following list are located on the rear panel of the Notebook.
Page 71 Serial Device This is a standard 9-pin serial port. Any device that uses this standard can be connected to the Notebook. For example, most pointing devices such as a mouse or graphic tablet, can be directly connected to the computer. External MODEMs or fax/MODEMs will usually employ a standard cable.
Page 72: Connecting Peripheral Devices
Notebook User’s Guide USB Devices The Notebook is equipped with a Universal Serial Bus (USB) connector. USB devices are PnP compliant as defined by the Universal Serial Bus Specification 1.0. Any device that complies with this standard can be connected to this port. RJ-11 MODEM To use the Notebooks...
Page 73 To activate the external monitor you will need to press the hot key combination. Press [Fn] + [F5] on the Notebook’s keyboard to toggle between the Notebook’s LCD display, simul-scan (simultaneously viewing the Notebook’s LCD and external monitor screen) and an external monitor. The Notebook’s display panel will be turned off and the external monitor will become the active display.
Page 74 Notebook User’s Guide Connecting Serial Devices The Notebook has one Serial Port. Please refer to Figure 4-3. Its address can be set via the BIOS Setup program. Refer to Chapter 2 for information on BIOS Setup. Figure 4-3: Connecting a Mouse to the Notebook’s Serial Port Connecting An External Keyboard The Notebook has a connection for a full-size enhanced 101/102-key keyboard commonly used with desktop computers.
Page 75 PCMCIA Card Bus Cards and Expansion Sockets Your Notebook computer features two PCMCIA expansion sockets designed to interface with two Type II cards or one Type III card. This sophisticated innovation allows you to expand and customize your Notebook computer to meet a wide range of computing needs without sacrificing portability.
Page 76 Notebook User’s Guide Figure 4-5: Inserting and Ejecting a PCMCIA Card Zoomed Video Port As part of the Notebook’s advanced architecture, the Zoomed Video port (ZV port) feature provides you with hardware MPEG support. This feature allows you to insert a ZV Port-compliant MPEG PC Card into one of the Notebook’s PCMCIA expansion sockets.
Page 77 To take advantage of this feature, your MPEG PC Card must be ZV Port-compliant. For installation instructions and details on how to use a ZV Port-compliant MPEG PC Card, refer to the user’s manual that comes with the PC Card. Before you can use an MPEG PC Card you must disable the internal MPEG II Card in the BIOS Setup program.
Page 78 Notebook User’s Guide 1. Connect the phone line to the test the line first with a telephone to make sure you hear a dial tone. 2. Now install the Module. The Driver Windows 95 Utility Diskette. Refer to the README file on the utility diskette for instructions on installing this driver.
Page 79: Chapter 5
HAPTER OWER YSTEM This chapter contains information on the Notebook’s power system, including the AC Adapter, the battery system, recharging the battery, and tips for conserving battery power. Also included is a detailed description of power management and each of the power modes. The power system is comprised of two parts, the AC Adapter and the battery system.
Page 80: The Ac Adapter
Notebook User’s Guide The AC Adapter The AC Adapter’s primary function is to provide power to the computer. Refer to Chapter 1 for instructions on how to connect the AC Adapter to the computer. When the Adapter is connected to the computer, it provides power as long as it is plugged into an electrical outlet.
Page 81 A new battery pack should be fully discharged and re- charged three times before being used. A fully charged pack will provide approximately 3 hours of battery life before you have to recharge or replace the battery. Additional battery packs are optional pieces of equipment and can be purchased separately.
Page 82: Removing The Battery Pack
Notebook User’s Guide Figure 5-3: The Main Battery Module Notice on the rear of the battery casing there are 5 LEDs and a status button. Please refer to Figure 5-3. These LEDs indicate how much battery life is remaining. Press the status button to check the battery’s charge. If all five LEDs light, the battery is charged to full capacity.
Page 83: Inserting The Battery Pack
4. Now, gently pull the module out of its housing (2). The release latch is spring-loaded and will snap back into place when you release it. Figure 5-4: Removing the Battery Pack Inserting the Battery Pack To insert the battery pack into the Notebook refer to Figure 5-5 and the following instructions: 1.
Page 84: Automatic Battery Pack Charging Function
Notebook User’s Guide Automatic Battery Pack Charging Function There are two ways to charge a battery pack. One is by the aid of the AC Adapter, and the other is by using the optional Battery Pack Charger. This chapter will focus on recharging the battery using the AC Adapter. Recharging the battery by way of the external battery charger is covered in Chapter 6.
Page 85 Figure 5-6: Connecting the AC Adapter to the Notebook’s AC port 1. Insert the end of the AC Adapter output cable into the Notebook’s AC port. Please refer to Figure 5-6. 2. Connect the power cable to the port on the AC Adapter module. Please refer to Figure 5-7.
Page 86: Using Battery Power
Notebook User’s Guide Using Battery Power The battery system will provide approximately Notebook when Power Management is disabled. depending on how you use the power saving features, your general work habits, and the type of CPU and LCD that your Notebook has. We recommend you use the AC Adapter as often as possible to conserve battery power.
Page 87: Power Management Habits
Small Battery for Real Time Clock There is a small built-in battery pack that supplies power to the system in order to maintain certain system information while the power is off. Power Management Habits While operating the Notebook on battery power, it is important to develop good power saving habits to maximize battery life.
Page 88: Power Management Modes
Notebook User’s Guide Screen Brightness The brighter the LCD display screen is, the more electricity it requires. Avoid setting the screen brightness level higher than necessary to extend the duration of battery power. The Serial Ports The computer has one serial port that draws some power if Enabled, even though no serial device is being used with the computer.
Page 89 Suspend Time-out Mode This mode saves power by cutting off the power of the CPU and DMA clocks, suspending the math co-processor, turning the video off, and turning off all controllable peripheral devices. The Notebook enters Suspend Time-out mode when the system remains Standby mode for a specified amount of time. This time value can be set from the Power Menu in the BIOS Setup program.
Page 90 Notebook User’s Guide A Suspend Example The Time-out settings for Standby and Suspend Time-out specify the amount of time the system must be inactive before the next power management level is enabled. The example below demonstrates this functionality. If the Standby Time-out is set to 2 minutes, and the Suspend Time-out is set to 5 minutes, then the following power management events take place: 1.
Page 91: Controllable Features
= The DRAM and video memory are saved to the hard disk (Save to Disk only) If the system is left in Suspend to memory (RAM) mode long enough to consume all battery power, then the Suspend indicator goes out and the current contents of the computer’s memory are lost.
Page 92: Cover Lid Switch
Notebook User’s Guide Cover Lid Switch The Notebook’s LCD Cover Lid Switch is located to the right of the System Status window. See Figure 1-4. If the Notebook is powered on and the lid is closed, the LCD panel will power off and the display will be switched to the CRT monitor connected to the VGA port.
Page 93: The Apm Interface
The APM Interface In addition to the power saving features built into the resident BIOS System Configuration Utility, your Notebook also supports the Intel-Microsoft Advanced Power Management (APM) version 1.2 (or higher) specification. APM is a cooperative interface that enhances the Notebook’s built-in power management features by providing one of the most accurate schemes for detecting true idle.
Page 94 Notebook User’s Guide This concludes this chapter on the Notebook’s power system. Chapter 6 provides instructions for inserting memory expansion modules and connecting the Notebook to a proprietary I/O Replicator and Docking Station.
Page 95: Chapter 6
XPANSION PTIONS This chapter describes the optional equipment that can be added to the basic Notebook system. We use the term expansion here to signify items that are installed inside the computer rather than standard equipment such as a printer that can be connected to the computer’s I/O ports.
Page 96: Installing Memory Cards
Notebook User’s Guide Installing Memory Cards Your Notebook’s computer chips, especially RAM (random access memory), are extremely static-sensitive. computer chips. It is therefore important to discharge the static electricity from your body before installing the memory module. electricity by touching the metal shielding around the connectors on the rear of the Notebook computer.
Page 97: Installing And Removing Modules
Installing and Removing Modules Your Notebook has the added feature of being capable of supporting three optional hardware modules. The addition of these modules increases your Notebook’s versatility and performance. All modules are installed in the Notebook’s Bay 2 port. The battery pack is in Bay 1.
Page 98 Notebook User’s Guide Installing the Combo Module and Optional Modules For step by step information on installing any one of the modules into Bay 2 of the Notebook, please refer to the following: 1. Ensure that the Notebook is in the power-off mode before installing a module.
Page 99: Optional Modules
Optional Modules The Battery Module The optional battery module allows for extended battery power when you are on the road. The Notebook’s battery module will run out of power after approximately 3.0 hours of use. An extra battery module allows you more flexibility in your away from the office schedule, adding an additional 3.0 hours to the computer’s operational time.
Page 100: Removing And Installing Hdd Modules
Notebook User’s Guide Loading a Disc To play a CD disc, follow the instructions listed below. 1. Press the eject button. The tray ejects from the drive. 2. Place the disc into the tray with the disc’s label facing up. 3.
Page 101 Chapter 6: Expansion Options Figure 6-4: Removing the HDD Module (A) Figure 6-5: Removing the HDD Module (B)
Page 102 Notebook User’s Guide Lift the HDD out of the bay (3). Store your HDD module in a safe, dry place away from direct sunlight or heat. To install a new HDD module follow the above instructions in the reverse order and refer to Figure 6-6 and Figure 6-7. Figure 6-6: Installing the HDD module (A) Figure 6-7: Installing the HDD module (B)
Page 103: The I/O Port Replicator
Chapter 6: Expansion Options The I/O Port Replicator The I/O Port Replicator features the most innovative advances in Notebook personal computing technology. Much consideration has gone into the design of the I/O Port Replicator in order to meet your requirements for versatility as well as quality.
Page 104: The Ac Adapter And Peripherals Connection
Notebook User’s Guide The AC Adapter and Peripherals Connection The AC Adapter port and all peripheral ports are located on the rear side of the I/O Replicator. Please see Figure 6-8 for a complete port layout. You will want to place the I/O Port Replicator flat on a desk near a wall outlet or an extension cord with a built-in circuit breaker.
Page 105: Removing The Notebook From The I/O Port Replicator
Figure 6-9: Connecting the Notebook to the I/O Port Replicator 4. Gently slide the Notebook along the rails of the docking platform until the Notebook’s 240-pinned connector makes a connection with the 240-pinned port on the Replicator. If the Notebook does not slide in easily, remove it from the docking platform, realign the grooves to the rails and try again.
Page 106: I/O Replicator Specifications
Notebook User’s Guide Figure 6-10: Removing the Notebook from the I/O Replicator I/O Replicator Specifications External Interfaces = One PC/AT compatible parallel port = One PC/AT compatible RS232C serial ports = One external VGA monitor connector = One external keyboard connector for PC/AT compatible keyboard = One external PS2 mouse connector = Three audio connectors (Microphone, Headphone-out, Line-in) = One USB Connector (two slots)
Page 107: Chapter 7
ARING FOR YOUR General Maintenance The best maintenance you can perform yourself is preventive. Try to keep the computer as clean as possible. Avoid transporting or using it in dirty or dusty environments if possible. Use the carrying bag provided or some other clean container when you transport the computer.
Page 108: Cleaning The Computer
Notebook User’s Guide Cleaning The Computer Cleaning The Case If the computer case becomes soiled, you can clean it. Always make sure that the computer is turned off and the AC adapter is disconnected before cleaning the computer. You can clean the case with a soft, preferably lint-free, cloth. If necessary, you can use a mild detergent.
Page 109 Cleaning the Diskette Drive In order to avoid causing damage to the sensitive read/write heads and diskette surface, it is important to prevent dust particles and dirt from entering the disk drive slot. If you suspect that the floppy disk drive needs cleaning, you can purchase a disk drive cleaning kit from your computer dealer.
Page 110: Caring For Diskettes
Notebook User’s Guide Caring for Diskettes Under normal conditions, a diskette’s rigid plastic case will protect it from damage. However, data stored on floppy diskettes are easily corrupted. Follow the protective measures listed below to preserve the integrity of data stored on floppy diskettes.
Page 111 = Never push any objects of any kind into cabinet openings. They may touch dangerous voltage points or short parts that could result in fire or electrical shock. = Turn off the Notebook before installing or removing a peripheral device. = Turn off the Notebook and disconnect the AC adapter before cleaning.
Page 112 Notebook User’s Guide...
Page 113: Troubleshooting
PPENDIX ROUBLESHOOTING Your Notebook has passed through a series of rigorous quality assurance tests to guarantee reliable performance. However, a computer is a sophisticated piece of equipment and as such may malfunction if used incorrectly or if one of its components fails. This chapter will try to anticipate potential problems that you may encounter in the day-to-day use of your computer.
Page 114: An Approach To Troubleshooting
Notebook User’s Guide An Approach to Troubleshooting In general, troubleshooting involves an organized system of approach to problem solving. Try to isolate the problem and identify the defective device (hardware) or improper setting (software). When you have a problem, you should do a thorough visual inspection of the Notebook.
Page 115 Booting Up Question: When I turn the Notebook on, I can’t get an operating system prompt to appear on the screen. The Notebook does seem to be running, though. Answer: Make sure that you have properly installed an operating system on the hard disk.
Page 116: I/O Connections
Notebook User’s Guide I/O Connections External Monitor Question: Is it possible to use both an external and the LCD screen at the same time? Answer: Yes, the Notebook provides three display configurations: LCD, monitor, and Simul Scan (LCD & MONITOR active at the same time). [Fn] + [F5].

This manual is also suitable for:

S6800

Sceptre S6500 User Manual

Chapter 1

Introducing the Notebook

Chapter 2

The BIOS Setup Program

Chapter 3

Operation

Chapter 4

Peripherals

Chapter 5

The Power System

Chapter 6

Expansion Options

Chapter 7

Caring for Your Notebook

Appendix A Troubleshooting

Quick Links

Troubleshooting

Need help?

Questions and answers

Related Manuals for Sceptre S6500

Summary of Contents for Sceptre S6500

This manual is also suitable for:

Table of Contents