TVT TD-2104TS - HD TVI DVR Quick Start Guide

TVT TD-2104TS - HD TVI DVR Quick Start Guide

Also See for TD-2104TS:

Advertisement

TVT TD-2104TS - HD TVI DVR Quick Start Guide

Notes

  • Please read this instruction carefully for correct use of the product and preserve it for reference purposes.
  • All the examples and pictures used here are for reference only.
  • There may be several technically incorrect places or printing errors in this manual. The updates will be added into the new version of this manual. The contents of this manual are subject to change without notice.
  • This device should be operated only from the type of power source indicated on the marking label. The voltage of the power must be verified before using the same.

Packing Check

Please check the device and the accessories after getting the device. If there are any damages, shortages or defects, please contact your dealer immediately.

HDD Installation

This series of the product supports 1 SATA hard drive. Please make sure that the device is powered off before the installation. The pictures of the installation are only for reference, please take the real object as the standard.

  1. Loosen the screws to open the
    HDD Installation - Step 1
  2. Get the HDD ready. cover.
    HDD Installation - Step 2
  3. Put the HDD onto the bottom of the device.
    HDD Installation - Step 3
  4. Connect the power and data cables.
    HDD Installation - Step 4
  5. Turn over the machine and secure the HDD with the screws.
    HDD Installation - Step 5
  6. Install back the cover and secure it with the screws.
    HDD Installation - Step 6

Rear Panel Instruction

The interfaces of the rear panel are for reference only.
Rear Panel Overview

Startup & Shutdown

Startup

  1. Connect the monitor.
  2. Connect the power.
  3. The device will boot and the power indicator will display blue.
  4. A wizard window will pop up.

Shutdown

Go to "Main Menu" and then select "Shutdown" icon. This will bring up a shutdown window. The device will shut down by clicking "OK" button. Then disconnect the power.

Login

After the wizard setup, you can see the live image. Right click to pop up a menu toolbar. Click Main Menu button. This will take you to see a login box. The default username is admin; the default password is 123456. Enter username and password and click "Login" button to go to the main menu setup.
Login Box

NAT

NAT Settings

  1. The DVR shall be powered on and connected to the network.
  2. Go to Main Menu→Setup→Network→Network. Refer to Fig 1. You can obtain the IP address, Subnet Mask and Gateway automatically. You can also manually enter them according to the actual network situation. Please make sure the network segment is the same as that of the network which is used.
    NAT Settings - Step 1
  3. Set the preferred or alternative DNS Server. Click "Apply" to save the parameters.
  4. Go to Main Menu→Setup→Network→NAT tab. Refer to Fig 2.
    NAT Settings - Step 2
  5. Enable NAT and input the NAT Server (The default NAT Server is www.autonat.com).
  6. Click "Apply" to save the parameters.

NAT Access

After finishing the NAT settings, input www.autonat.com in the address bar to go to the IE client. If you are the first time to access the NAT, you shall download and install the ActiveX according to the popup tips. After installing ActiveX successfully, it will pop up the login box.
NAT Access
Device Serial Number: The MAC address of the DVR (Go to Main Menu→Information→Network to check the MAC address of the DVR).
Username: The username of DVR. The default username is admin.
Password: The password of DVR. The default password is 123456.

DDNS & UPnP Function

Quick DDNS Setup

You may set up DDNS to be used in connection when your device is set to use PPPoE as its network connection.

  1. Go to Main Menu→Setup →Network→Other Settings interface.
  2. Make sure the DDNS type " www.autoddns.com". Then self-define the host domain. After you register it successfully, save the settings by clicking "Apply" button. Now, you can remotely access the device using the domain name via WAN.
    Other Settings interface

UPnP

You can use the UPnP function to enable the fast connection of the device to WAN via a router without port mapping.

  1. Go to Other Settings tab and enable the UPnP and click "Apply" button to save.
  2. Enable the UPnP function in the router.

Note: Before setting UPnP function, please configure the correct local IP address, subnet mask, gateway and DNS according to the router. Make sure the HTTP port and data port are correctly set. Make sure the router supports UPnP function.

Manual Recording

Before recording, please install and format a HDD. Right click the mouse in the live interface to pop up the following menu toolbar. Click button to start recording.
Toolbar

Playback

Right click the mouse in the live interface to pop up the menu toolbar. Click the little triangle button beside button to set playback time (eg. 5 minutes). Then click button to play the record from the past 5 minutes. You may control the video by clicking the corresponding buttons, such as, forward, play/pause, stop, etc. If you want to play the record by searching the specific time and date, event or file, you may refer to the DVR User Manual for details.
Playback

Documents / Resources

References

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download TVT TD-2104TS - HD TVI DVR Quick Start Guide

Advertisement

Need help?

Need help?

Do you have a question about the TD-2104TS and is the answer not in the manual?

Questions and answers

Table of Contents