TVT TD-2932TD-HP Quick Start Manual

Hybrid DVR

Quick Start Guide

1. Notes

● Please read this instruction carefully before operating the unit and
keep it for further reference.
● All the examples and pictures used here are for reference only.
● The contents of this manual are subject to change without notice.
● This device should be operated only from the type of power source indicated
on the marking label. The voltage of the power must be verified before using
the same.

2. Packing Check

Please check the device and accessories after getting the device. If there are
any damages, shortages or defects, please contact your dealer immediately.

3. HDD Installation

This series of the product supports 8 SATA hard drives. The pictures of the
installation are only for reference, please take the real object as the standard. Please
make sure that the device is powered off before the installation.
① Remove the cover and loosen the screws to take out two mounting bars.
② Fix the HDDs on the mounting bar with screws.
③ Install the two mounting bars with HDDs back to the device ( It is recommended to
install the copper-pillar provided in case the HDDs are damaged by external forces ).
④ Connect the power and data cables.
⑤ Install back the cover and secure it with the screws.
Tips: Please check the inside structure of the device and make sure the cables connected
well before installing the cover back.

4. Rear Panel Instruction

The interfaces of the rear panels are for reference only.
AUDIO IN Connectors for audio input
VIDEO IN Connectors for video input
Connectors for audio output
AUDIO OUT
MIC IN Connect to a microphone used for two-way talk
CVBS CVBS video output connector
LAN1/2 RJ 45 1000Mbps Ethernet ports
VGA Connect to monitor
HDMI1 Connect to monitor, used as main output
HDMI2 Connect to monitor, used as secondary output
USB3.0/USB
Connect to USB storage device or USB mouse
K/B: connector for a keyboard. A is TX+; B is TX-
RS 485
P/Z: connector for a PTZ device. Y is TX+; Z is TX-
ALARM OUT Connector for alarm output devices
ALARM IN Connector for alarm input devices, like sensors
Connect to the HDD with e-SATA interface
E-SATA
5. Startup & Shutdown
►Startup
① Connect the monitor and the power.
② The device will boot and the power indicator will display blue.
③ A wizard window will pop up.
►Shutdown
Click "Start" and then select "Shutdown" icon. This will bring up a shutdown
window. The device will shut down by clicking "OK" button. Then disconnect
the power.

6. Login

You must configure the wizard if you start the DVR for the first time.
username is admin and the default password is 123456.
password as needed and then click "Edit Security Question" to set questions
and answers for retrieving password.
Wizard
Admin Password Setup
Username admin
Password 123456
123456
Confirm Password
Display Password
Pattern Lock
Enable
Edit ecurity S Q uestion

7. Analog Camera Connection

First connect the camera to the DVR. Then go to Start → Settings → Camera
→ Manage Camera → Camera Signal to set the signal mode of camera. The
actual signals input shall correspond to the video mode. Please refer to User
Manual for details.
8. Network Configuration & Add IP Camera
After you finish adding IP cameras, you can see the live images through the monitor
of the DVR. The following will mainly introduce how to add the IP cameras via
LAN/WAN. This DVR has two network ports, you can select the network work
pattern as needed. Network fault tolerance and multiple address setting are optional.
Network Fault Tolerance: Bound two network ports to one IP address. This pattern
can increase the network bandwidth and form a network redundant array to share the load.
When one port goes wrong, the other port will take over the entire load immediately and
seamlessly.
Multiple Address Setting: You shall set the IP address, subnet mask, gateway and
DNS of each ethernet port respectively.
The pictures are only for reference, please refer to User Manual for details.
►LAN
① Set the network of the DVR. Go to Start → Settings → Network →TCP/IP. Enter
IP address, subnet mask, gateway, etc. If using DHCP, please enable DHCP in both the
NVR and the router.
② Go to Start → Settings → Network → Port. Enter HTTP port (the default value
is 80), server port (the default port is 6036).
③ Click "Apply" to save the settings.
IP Address Settings
The default
Please change the
④ Go to Start → Settings → Camera → Add Camera. The DVR will automatically
refresh the list of online IP cameras which are in the same local network with
the DVR. Click
Quickly Add Manually Add
No. Address
1 192.168.2.45
Log In Automatically
Edit
Selected: 1/1
Remain Bandwidth: 10 / 10 Mb
Next Cancel
Network Fault Tolerance
Work Pattern (Modifying work pattern need to reboot )Gateway
Obtain an IPv4 address automatically Obtain an IPv6 address automatically
Address 192 . 168 . 1 . 2 Address
Subnet Mask Mask Length
0 . 0 . 0 . 0 0
Gateway 192 . 168 . 1 . 1 Gateway
Ethernet Port 1
Primary Card
Ethernet Port 2 ( Online )
Ethernet Port 1 ( Online )
MCA Address 10 . 151 . 151 . 1 MAC Address
1500
MTU
Obtain DNS automatically
Preferred DNS
. . .
to modify the IP address.
Edit IP
Add Camera
Mac Address CE :98 :23 :75 :35 :22
Address 192 .168 . 1 . 45
Port Edit Subnet Mask Protocol Model Version
Subnet Mask 255 . 255 . 255 . 0
4.0.0.1.beta1
80 255.255.255.0 XXX XXX
192 .168 . 1 . 1
Gateway
Username
admin
Password
OK
Default Password Add Cancel
Cancel