Page 1
GHP35 Instruction Manual.pdf 2019/10/17 3:27 PM PATIO HEATER SHORT STAND GHP31-Cement Grey • GHP32-Black • GHP33-Stainless Steel Life’s a Gas THIS IS A LOW PRESSURE APPLIANCE TO BE USED ONLY WITH A 2.8kPa SANS 1237 APPROVED REGULATOR (REGULAT SAN1156 HOSE &...
For use with LP gas only. DO NOT use this patio heater if you do not clearly understand the instructions and/or how to operate the controls. Phone the customer care line at 086 100 ALVA (2582) or email info@stingray.co.za for assistance. patio heater.
Page 3
HEATER SET UP Cautions and SAFE APPLIANCE LOCATIONS warnings. LEAK TEST USING YOUR HEATER FLASHBACK Danger CHANGING YOUR CYLINDER MAINTENANCE Contact an approved FREQUENTLY ASKED QUESTIONS ALVA technician. SPECIFICATIONS TROUBLE SHOOTING GUIDE AFTER SALES SERVICE Do It Yourself Instructional video available...
WARRANTY ’ Your Life Is Better With Alva Thank you for your purchase of this Patio heater. Please read these instructions carefully before use and keep them in a safe place, for future reference. Not using gas and/ or gas appliances...
Please refer to the parts list and diagrams. (see page 3 to 8) Assembly of the heater involves large components and it is advisable to have two people assemble the unit. This patio heater makes use of an industrial cylinder (9kg ALVA cylinder recommended) with a 5/8” BSP thread; horizontal exit valve.
HEATER SET UP (Figure B) Nose cone sealing washer Fig.B Use 2pcs M8x16mm bolts and M8 nuts to connect M8 Flange Nut bracket with wheels to the base. M8 x 16 mm Bolts Wrench Fig C...
Page 8
6. Use 4pcs M5x8 screw to Screw M5 x 8 join the tank housing base and stand. Philips screwdriver Fig D 7. Use 4pcs M5x8 screw to Screw M5 x 8 join the burner head and tank housing body. Philips screwdriver Fig E 8.
Page 9
Install the double-ended stud on the aluminum reflector as shown in the figure, and tighten the nut. Fig G Install the aluminum reflector on the three double-end studs as shown in the figure. M6 Dome Nut Fig H Insert the upper safety guard 4pcs feet into the lower guard 4pcs holes shown in (Figure I),...
Page 10
13. Position the cylinder M6 flange nut inside the housing (Figure K) and secure by cliping belt around cylinder. Fig K 14. Attach the hose and regulator and leak test both connections using a soapy water solution, see page 10 for leak test. (Figure L) DO NOT light the heater when performing this leak test.
Page 11
SAFE Minimum Clearance from Combustible Surfaces: 1000mm 1000mm Flame screen guard Burner assembly Base of control housing Tank housing Base The heater is primarily for outdoor use only. Always ensure that adequate fresh air ventilation is provided. Always maintain proper clearance from combustible materials, Side 1000mm, Rear 1000mm, Ceiling 1000mm minimum.
Cylinder. Extinguish all If you are unsure or if you cannot tighten the connection, DO NOT operate any electrical appliances. 086 100 ALVA Ventilate the (2582) area. Connections to be leak tested Check for leaks Regulator into cylinder (see LEAK TEST)
Page 13
Smoke and odour caused by the heating of oils used during pilot ame position and press ignition button. manufacturing will Keeping the control knob depressed, the pilot ame will occur when lighting ignite next to the burner. Keep the knob depressed for another 10 seconds to allow the ame failure safety system time.
If faults are suspected or detected, stop using the heater and contact ALVA. Clean the exterior and storage area of your heater when required to remove dust. DO NOT use abrasive products to clean the heater; these may damage the paint work.
Clean with a soft brush or blow clean with compressed air. If any part of the heater is in need of replacing, use only original Alva parts. Using any other spare parts is dangerous and will void the warranty. When the heater is not in use for extended periods, always keep the burner head covered.
If this gas weight exceeds your cylinder design weight http://www. (9kg) then return the cylinder to your gas supplier. youtube.com/ watch?v=Ya vsYE8nzCw &feature=plcp SPECIFICATIONS Model ALVA GHP31 Type of gas Operating pressure 2.8kPa Injector size 1.75mm Heat Output 11kW Gas Consumption...
Model ALVA GHP32 Type of gas Operating pressure 2.8kPa Injector size 1.75mm Heat Output 11kW Gas Consumption 800gr/hr at MAX Model ALVA GHP33 Type of gas Operating pressure 2.8kPa Injector size 1.75mm Heat Output 11kW Gas Consumption 800gr/hr at MAX...
Place pilot properly bent In poor location Position properly and retry AFTER SALES SERVICE MANUFACTURED FOR AND DISTRIBUTED BY Alva, a division of Stingray Accessory Manufacturers (Pty) Ltd. P.O. Box 30014 Tokai, 7966 Tel: 021 442 1540 E-mail: info@stingray.co.za www.alva.co.za /alvagas www.facebook.com/AlvaGas...
Need help?
Do you have a question about the GHP31 and is the answer not in the manual?
Questions and answers