Thank you for purchasing your new greenhouse. We recommend you familiarize yourself with the instructions and read all safety information before you commence assembly. These instructions are divided into sections: Base, Part lists, Preparation, Side wall, Rear wall, Front wall, Roof, Vent, Door, PVC capping bar, Polycarbonate or Glass, Down pipes, Optional Turbine Vent, Anchoring greenhouse to slab or base etc.
Important Before assembling your new greenhouse, please check that all parts in the provided list are included. Please take each bundle out of the packaging in order to identify the parts better. Most parts are num- bered and can be identified by a stamped number or removable label. Alternatively, the components can be identified by lengths detailed in the packing list (see diagram below).
Base-Optional Article No: GS010996 We cannot emphasis how important it is to have a proper base for your Greenhouse to be erected upon. It is essential that the BASE IS FLAT, LEVEL AND SUBSTANTIAL enough to take the weight of the greenhouse including its polycarbonate panels or heavy glass.
Page 5
Base IMPORTANT Before assembling aluminium base, the end trough centers of seven legs should match both end trough centers of side sills and front & rear sills at the same time. Please match six legs troughs together at the same time...
Page 6
Anchoring building to slab / concrete base For this final stage you will need No.10 X 2” screws, grey wall plugs, a 8mm ma- sonry drill bit and a hammer drill. Fixing the greenhouse to the ground is very simple to do. When you built the front, rear and side assemblies you will have attached base brackets (m5) in spe- cific places around the building.
Page 9
BASE Base dimensions and recommendations. Ensure that your base is level as this will make assembly of the building, especially the glazing of the roof much more straight forward. PARTS LIST Most components should have a code punched into their metal surface. Identify and separate all like for like components prior to assembly.
Page 10
Join 12 short roof glazing bar #7920 between vent hinge beam #7922 and eave. At this stage you need to decide where your roof vent are positioned so that you could insert an extra bolt into #7920 glazing bar either side of a vent opening. Assemble the outer hexagonal ridge cone #7994 over the assembled profiles on hexagonal bracket, using long bolt #a24, spacer #7991, open-close disc #7993 and locknut #a25.
Page 23
Door 7065 a15/a16/a2 a15 round head M6x12 door stop bolt and gasket should be fixed in center door track rail. 7936 G-p5...
Page 24
Silicone Waterproof Alu. Foil tape 100mm x 6pc...
Page 25
PVC Capping Bar Step6 Step1 Step4 Step3 Step2 Step5 Note: PVC capping bars were pushed in place from both top and bottom in diagonal direction to- gether. If you assemble it from one side by one side, you will fell space is too tight to assemble an- other PVC capping bar.
Page 26
10mm Polycarbonate sheet six corners same twelve corners same c-758 c-1508 c-1508 c-758 c-758 c-1508 c-1508 c-758 Length Size 1508 680 x 413 1348 Panel 700 x 258 Roof 700 x 0 / 1397 700 x 0 / 1397 700 x 698 Panel 700 (350) x 698 700 (350) x 698...
Page 30
Article No: GS010995 Optional Turbine vent is optional * Remove hexagonal ridge cone firstly. * Assemble open-close disc #7993 on hexagonal bracket by using short M6 bolt #a1 instead of long #a24. * Attach turbine vent on roof corner bars by carefully using self-drilling tapping screws #a18 which will bore into aluminium or plastic.
Page 31
The list of parts Description Side wall Rear & Front wall Roof Vent Door PVC capping bar Downpipe Polycarbonate panels Tools Assembly Instruction...