Subscribe to Our Youtube Channel
Related Manuals for Energer ENI512DDH
Summary of Contents for Energer ENI512DDH
- Page 1 SAFETY AND OPERATING MANUAL Original Instructions V 6.0 18V CORDLESS DRILL ENI512DDH...
- Page 2 Read all safety warnings and all instructions before use. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. 18V CORDLESS DRILL ENI512DDH...
-
Page 3: General Safety Instructions
Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of a power tool may result in personal injury. e) Do not overreach. Keep proper footing and balance at all times. This enables 18V CORDLESS DRILL ENI512DDH... - Page 4 Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns. 18V CORDLESS DRILL ENI512DDH...
-
Page 5: Special Safety Instructions
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well-ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles. 18V CORDLESS DRILL ENI512DDH... - Page 6 It must ensure that the battery pack is adapted to the tool and is reloaded with an appropriate recommended charger (battery reference ENI513BAT, charger reference ENB514CHR) Incorrect use may result in electric shock, overload or electrolyte leakage. 18V CORDLESS DRILL ENI512DDH...
- Page 7 8. Always disconnect battery charger and remove battery from charger when the charging is complete. 9. Only use the battery charger specifically stated on the base of the battery. 10. Don’t charge non-rechargeable battery. 18V CORDLESS DRILL ENI512DDH...
-
Page 8: Noise Information
And the tool is being used as intended by its design and these instructions. While working with this power tool, hand/arm vibrations occur. Adopt the correct working practices in order to reduce the exposure to vibration. 18V CORDLESS DRILL ENI512DDH... - Page 9 The following dangers can arise in connection with the structure and design of this product: 1. Health defects resulting from vibration emission if the product is being used over long periods of time or not adequately managed and properly maintained. 18V CORDLESS DRILL ENI512DDH...
- Page 10 The machine is intended for driving in and loosening screws and bolts as well as for tightening and loosening nuts within the respective range of dimension. And it can be used to drill holes on wood, plastic or metal. 18V CORDLESS DRILL ENI512DDH...
- Page 11 Before charging, read the instructions This symbol indicates that this battery contains lithium. This battery shall be brought to your shop to be recycled. Safety thermal fuse yyWxx Manufacturing date code: Year of manufacturing (20yy) and week of manufacturing (Wxx); 18V CORDLESS DRILL ENI512DDH...
-
Page 12: Components And Controls
3 Forward, reverse rotation and lock control 4 ON/OFF switch with variable speed control 5 Battery pack 6 Gear control LED light LED battery capability indicator Charger 10 Charging base 11 Battery pack release button 12 Bit Holder 18V CORDLESS DRILL ENI512DDH... -
Page 13: Technical Data
TECHNICAL DATA Item reference ENI512DDH Rated voltage: No load speed: 0-400 min /0-1300 min Chuck capability: 13mm Number of clutch position: 21+D Torque setting(For drilling) Maximum torque: 25N.m Max drilling capability: Wood: 30 mm Steel: 13 mm Machine weight: 1.6 kg... -
Page 14: Charging Procedure
ALWAYS disconnect the charger from the power source when it is not in use. State of Charge (fig.5): -When charging begins: the indicator changes from green to red. -When the load is over: the indicator changes from red to green. (fig. 5) 18V CORDLESS DRILL ENI512DDH... -
Page 15: Installing And Removing Bits
(fig. 8) Insert the magnetic bit holder in the chuck according to above steps and place the bit into the holder which been selected.(Fig.9) To remove the bits, just pull out the bit by hand. (fig. 9) 18V CORDLESS DRILL ENI512DDH... -
Page 16: Variable Speed
(Fig.12) Warning: To prevent gear damage, always allow the chuck to come to a complete stop before changing the direction of rotation or the two-speed gear control. 18V CORDLESS DRILL ENI512DDH... -
Page 17: Torque Adjustment
Discharge your battery pack by operating your drill, then remove the battery pack from the drill housing and cover the battery pack connections with heavy duty adhesive tape to prevent short circuit and energy discharge. 18V CORDLESS DRILL ENI512DDH... -
Page 18: Terms Of Use
In case of problems or for a deep cleaning, consult the manufacturer, its service agent or a similarly qualified person to avoid a hazard. If the power cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard. 18V CORDLESS DRILL ENI512DDH... -
Page 19: Environmental Protection
GUARANTEE This ENERGER product carries a guarantee of 12 months. If your product develops a fault within this period, you should, in the first instance contact the retailer where the item was purchased. This guarantee specifically excludes losses caused due to:... - Page 20 EN 61000-3-2:2006+A1:2009+A2:2009 EN 61000-3-3:2008 EN 60355-2-29:2004+A2:2010 EN 60355-1:2002+A11:2004 +A12:2006+A2:2006+A13:2008+A14:2010+A15:2011 EN62233:2008 Authorised Signatory and technical file holder Date : 22/04/2013 Signature:_________________ Name / title: Peter Harries / Quality Manager Powersmith (UK) LTD. Trade House, Mead Avenue ,BA22 8RT 18V CORDLESS DRILL ENI512DDH...
Need help?
Do you have a question about the ENI512DDH and is the answer not in the manual?
Questions and answers