Table of Contents
Advertisement
Quick Links
Wall Mounted Option
Read and understand this entire owner's manual, including all safety information, before plugging in
WARNING
or using this product. Failure to do so could result in fire, electric shock, or serious personal injury.
Keep this owner's manual in a safe place for future reference. If you sell or give this product away,
CAUTION
make sure this manual accompanies this product.
Pictures within this owner's manual are for reference only. Please refer to the actual product for
NOTICE
appearance.
120V AC; 60 HZ; MAXIMUM POWER 1500 WATTS
ALL ELECTRIC. NO WOOD OR CHARCOAL. NO GAS. NO VENTING REQUIRED.
OWNER'S MANUAL
YORKTOWN
ELECTRIC STOVE HEATER
MODEL# EFS-XB24B
Advertisement
Table of Contents
Related Manuals for Flame & Shade YORKTOWN EFS-XB24B
Summary of Contents for Flame & Shade YORKTOWN EFS-XB24B
- Page 1 OWNER’S MANUAL YORKTOWN ELECTRIC STOVE HEATER MODEL# EFS-XB24B Wall Mounted Option Read and understand this entire owner’s manual, including all safety information, before plugging in WARNING or using this product. Failure to do so could result in fire, electric shock, or serious personal injury. Keep this owner’s manual in a safe place for future reference.
-
Page 2: Important Safety Instructions
IMPORTANT SAFETY INSTRUCTIONS! WARNING Read these instructions carefully before using this heater! • • This heater is hot when the heat mode is in use. To avoid burns, DO NOT let bare skin touch hot surface. If provided, always use handles when moving this heater. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains at least 3 feet (0.9m) from the front of the heater, and keep them away from the sides and rear. - Page 3 WARNING • For residential use only! NOT for commercial use! Any commercial or public use of this heater voids all warranties , and could cause injury. • This product is not intended to be a primary heat source. It is for supplemental heat only. •...
-
Page 4: Tools Needed
PREPARATION Make sure all parts are dry, and the power cord and plug are not damaged. NOTICE See IMPORTANT SAFETY INFORMATION on pages 2 and 3. TOOLS NEEDED (NOT INCLUDED) Phillips Screwdriver PARTS AND HARDWARE 1. Remove all parts and hardware from the carton and place them on a clean, soft and dry surface. -
Page 5: Installation And Assembly
INSTALLATION AND ASSEMBLY ALWAYS make sure the unit is unplugged before beginning assembly! NEVER NOTICE move or clean the heater, or change the bulb, while it is plugged in. ALWAYS attach the feet before using! NEVER plug in or operate this unit if the feet NOTICE are not securely attached! STEP1: Carefully turn the Stove Heater(A) upside down and lay it on a clean soft surface. -
Page 6: Operation
OPERATION Read and understand this entire owner’s manual, including all safety information, before plugging in or using this product. Failure to do so could result in electric shock, fire, serious injury, or death. This heater is not intended to be a primary heat source. It is designed to provide NOTICE supplemental heat, and should not be left running to continuously for more than eight hours. -
Page 7: Control Panel Functions
CONTROL PANEL FUNCTIONS When this heat function is used for the first time, a slight odor may be present. NOTICE This is normal and should not occur again unless the heater is not used for an extended period of time. CONTROLS FUNCTION Press once to turn the power ON. -
Page 8: Remote Control Functions
REMOTE CONTROL FUNCTIONS DO NOT press the buttons too quickly. Give the unit time to respond to each NOTICE command. REMOTE CONTROL BUTTONS FUNCTION Press once to turn the power and flame ON. Press again to turn the power and flame OFF. POWER ON/OFF Press once for low heat (750w). -
Page 9: Remote Control Battery Installation
REMOTE CONTROL BATTERY INSTALLATION STEP 1: Push down gently and slide back to remove the Remote Control(D) battery compartment cover. STEP 2: Insert the 2 AAA Batteries(F) into the battery compartment, ensuring the polarity (+/-) matches the terminals as indicated in the battery compartment. STEP 3: Replace the battery compartment cover. -
Page 10: Maintenance
Maintenance Risk of electric shock! DO NOT OPEN any panels other than the bulb replacement plate! No user-serviceable parts inside! ALWAYS turn the heater OFF and unplug the power cord from the outlet before cleaning, performing maintenance, or moving this fireplace. Failure to do so could result in electric shock, fire, or personal injury. - Page 11 LIGHT BULB MAINTENANCE ALWAYS turn the heater OFF and unplug the power cord from the outlet before cleaning, changing the light bulbs, or moving this unit. Failure to do so could result in electric shock, fire, or personal injury. Light bulbs become very hot during use. Allow at least 10 minutes for the WARNING bulb(s) to cool before touching.
-
Page 12: Troubleshooting Guide
TROUBLESHOOTING GUIDE PROBLEM SOLUTION 1. Make sure the power cord is plugged into a working 120V AC electrical outlet. 2. Check for a tripped circuit breaker, or a blown fuse. There is no power to the unit. 3. If the unit had been working, but then turned off by itself, the temperature limiting control must be reset. -
Page 13: Faq - Frequently Asked Questions
CSA RATING LABEL & POWER CORD LABEL CSA Rating Label Power Cord Warning Label FAQ - FREQUENTLY ASKED QUESTIONS Question Answer What is the best way to You can email us anytime at fsesales@taijicrafts.com. contact Customer Service? No. This heater is not intended to be a primary heat source. It is Can I leave the heater designed to provide supplemental heat, and should not be left running overnight? - Page 14 LIMITED LIABILITY LIMITED LIABILITY This product is not intended to be used as a primary heat source. Read and understand all assembly and operating instructions, and all safety information and warnings before use. This product is not intended to be used as a primary heat source. Read and understand all assembly and operating instructions, and all safety information and warnings before use.