Advertisement
2. INTRODUCTION
Heavy-duty axle stands to safely support vehicles for extended periods of time. Large crutch for even load distribution. Heavy gauge steel frame
and base plate with welded construction gives superior strength and safety. Supplied with captive, multi-position pin load support. Sold in pairs.
3. SPECIFICATION
Model No: ................................................................. AS20.V2
Capacity (each): ........................................................ 20tonne
Capacity (pair): .......................................................... 40tonne
Minimum height: ......................................................... 332mm
Maximum height: ........................................................ 485mm
4. OPERATION
4.1.
Familiarise yourself with the product. Check that the stands are in good condition and that no damage has been sustained during
transit.
4.2.
Ensure the maximum load does not exceed 40tonne per pair of axle stands, (20tonne for each stand).
4.3.
Refer to vehicle manufacturer's instructions for recommended support points. Check that the points are in good condition.
4.4.
Ensure the vehicle has been placed in gear and that the handbrake has been applied. (For automatics select the 'Park' mode).
4.5.
Adjust height of stand to correspond with the raised vehicle.
4.6.
Check that the locking pin (fi g 1 - 3) is correctly pushed all the way through the centre column (fi g 1- 1) and out of the other side, then
position stands under vehicle at points recommended by vehicle manufacturer.
4.7.
Carefully and slowly lower the load onto stands. Ensure the load bearing points sit in the center of the stand saddle and check that
the stands are stable and not leaning. Also ensure that there are no objects or persons that could impede the safe lowering of the vehicle
onto the stands.
4.8.
To remove stands, jack vehicle slightly so that stand can be removed.
4.9.
After use, hold the centre column (fi g 1 - 1) fi rmly when removing the locking pin (fi g 1 - 3). Failure to do so will allow the center column
to fall freely through the main center tube (fi g 1 - 2) with the risk of personal injury.
4.10.
When not in use place the locking pin ( fi g 1 -3) into it's circular holder (fi g 2 - 1) and leave the centre column (fi g 1 - 1) in it's lowest
position to minimise corrosion.
WARNING! Ensure you follow all instructions carefully. Failure to note these warnings may cause damage, serious injury or loss of life.
5. MAINTENANCE
5.1.
Before each use check to ensure stands and stand welds are not cracked, and that there are no missing and/or damaged parts.
WARNING! Any stand that appears to be damaged in any way must be removed from service immediately.
5.1.1.
Ensure the locking pins are in good order and condition.
5.1.2.
Due to the potential hazards associated with these stands, do not misuse, or make any modifi cation to the stands or components.
5.1.3.
It is the responsibility of the stands owner to ensure the operator has read these instructions, and that the operator is familiar with
the stands use and limitations.
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice. Please note that other versions of this product are available. If you require documentation for alternative versions, please email or call
our technical team on technical@sealey.co.uk or 01284 757505.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500
© Jack Sealey Limited
fi g.1
01284 703534
sales@sealey.co.uk
Original Language Version
fi g.2
AS20.V2 Issue 1 24/06/21
www.sealey.co.uk
Advertisement
