Samsung DC40E Quick Setup Manual

Quick Setup Guide
DC32E DC40E DC48E DC55E
- Recommended hours of use per day of this product is under 16 hours.
If the product is used for longer than 16 hours a day, the warranty may be void.
- The colour and the appearance may differ depending on the product, and the specifications
are subject to change without prior notice to improve the performance.
- Download the user manual from the website for further details.
http://www.samsung.com/displaysolutions
The terms HDMI and HDMI High-Definition Multimedia Interface, and the
HDMI Logo are trademarks or registered trademarks of HDMI Licensing
LLC in the United States and other countries.
Checking the Components
Contact the vendor where you purchased the product if any
components are missing.
The pictures may look different from the actual components.
Warranty card
Quick Setup Guide Power cord
(Not available in some locations)
Batteries
Remote Control RS232C(IN) adapter
(Not available in some
locations)
AV/Component
AUDIO adapter
adapter
BN68-07775H-01
Control Panel
Speaker
DC32E
Speaker
Power on the product.
1
If you press the button when the product is turned on, the control
menu will be displayed.
- To exit the OSD menu, press and hold the panel key for at least one second.
2 Move to the upper or lower menu. You can also adjust the value of an option.
Move to the left or right menu.
3
- You can adjust the volume by moving the panel key left or right
when the control menu is not displayed.
Remote sensor
4
Press a button on the remote control pointing at the sensor on the
front of the product to perform the corresponding function.
5 Spacer logo (Optional)
Do not pull on the spacer logo using force. The logo may tear or break off.
Reverse Side
IR IN RS232C IN RGB IN
Connects to the audio of a source device.
1
2 Connects to a source device using the AV/Component adapter.
Receives sound from a PC via an audio cable.
3
Connect to a USB memory device.
4
DVI IN: Connects to a source device using a DVI cable or HDMI-DVI cable.
5
MAGICINFO IN: Use the (dedicated) DP-DVI cable when connecting a network box (sold separately).
6 Connects to a source device using an HDMI cable.
Supplies power to the external sensor board or receives the light sensor signal.
7
Connects to MDC using an RS232C adapter.
8
9 Connects to a source device using a D-SUB cable.
Connects to MDC using a LAN cable.
0
Troubleshooting Guide
Issues Solutions
The screen keeps Check the cable connection between the
switching on and off. product and PC, and ensure the connection is
secure.
No Signal is displayed
Check that the product is connected correctly
on the screen. with a cable.
Check that the device connected to the
product is powered on.
Not Optimum Mode is This message is displayed when a signal
displayed. from the graphics card exceeds the product's
maximum resolution and frequency.
Refer to the Standard Signal Mode Table and
set the maximum resolution and frequency
according to the product specifications.
The images on the
Check the cable connection to the product.
screen look distorted.
The screen is not clear. Adjust Coarse and Fine.
The screen is blurry.
Remove any accessories (video extension
cable, etc) and try again.
Set the resolution and frequency to the
recommended level.
The screen appears Check that the resolution and frequency of the
unstable and shaky. PC and graphics card are set within a range
compatible with the product. Then, change the
There are shadows or
screen settings if required by referring to the
ghost images left on the
Additional Information on the product menu
screen.
and the Standard Signal Mode Table.
RJ45
Issues Solutions
The screen is too bright.
Adjust Brightness and Contrast.
The screen is too dark.
Screen colour is Go to Picture and adjust the Colour Space
inconsistent. settings.
White does not really Go to Picture and adjust the White Balance
look white. settings.
There is no sound. Check the connection of the audio cable or
adjust the volume.
Check the volume.
The volume is too low. Adjust the volume.
If the volume is still low after turning it up to
the maximum level, adjust the volume on
your PC sound card or software programme.
The remote control does Make sure that the batteries are correctly in
not work. place (+/-).
Check if the batteries are flat.
Check for power failure.
Make sure that the power cord is connected.
Check for any special lighting or neon signs
switched on in the vicinity.