Advertisement
6. USING THE COMPRESSOR
WARNING! Check the manual for items to be inflated to obtain the manufacturer's recommended inflation pressure.
‰
Avoid over inflation.
NOTE: Duty Cycle 5 minutes ON, 5 minutes OFF.
NOTE: Maximum pressure 60 psi
6.1.
INFLATING TYRES
6.1.1.
Pull the air hose from the stowage compartment at the back of the compressor (see fig.2) and ensure that the locking lever on
the valve connector is in the upright position i.e. in line with the connector.
6.1.2.
Remove the screw cap from tyre valve stem.
6.1.3.
Push the connector as far as possible onto the valve stem and push the locking lever through 90º to lock it.
6.1.4.
Switch on the compressor using the switch on the unit (see fig.2) and monitor the pressure on the air pressure gauge (see fig.2).
6.1.5.
When the desired pressure is reached, turn off the compressor, rotate the connector lever to the upright position and remove it
from the valve stem.
NOTE: It is recommended to use a separate air gauge to double check the actual inflation pressure achieved.
6.1.6.
Screw the cap back onto the valve stem.
6.2.
INFLATING PLASTIC INFLATABLE ITEMS e.g. balls, air beds, rubber rafts etc.
WARNING! Check the manual for items to be inflated to obtain the manufacturer's recommended inflation pressure.
‰
Avoid over inflation.
6.2.1.
Identify valve on product and remove any cover fitted.
6.2.2.
Identify the correct adaptor for the product and insert it into the inflation connector and push the locking lever through 90º to lock it.
6.2.3.
Insert the other end of the adaptor into the valve as far as possible.
6.2.4.
Switch on the compressor using the switch on the unit (see fig.2) and monitor the pressure on the air pressure gauge (see fig.2).
6.2.5.
When the desired pressure is reached, turn off the compressor, remove the connector and adaptor.
NOTE: It is recommended to use a separate air gauge to double check the actual inflation pressure achieved.
Replace any valve cover previously removed.
7. STORAGE
This unit may be stored in any position. Ensure that the clamps are securely attached to the clamping posts at the rear of the unit.
Store at room temperature. It is recommended to recharge the unit every two months when not in use and more frequently in
warmer or colder storage conditions to keep the battery in peak operating condition.
8. BATTERY REMOVAL
NOTE: The RoadStart battery is a sealed, lead-acid type. At the end of the RoadStart's service life it MUST be removed
and recycled, or disposed of properly, according to national and/or local regulations.
8.1.
REMOVAL
8.1.1.
Place the RoadStart unit front side down.
8.1.2.
Remove the 10 screws holding the casing together and lift off the back half of the unit.
8.1.3.
Undo and remove the nuts, bolts and washers on each battery terminal. The connecting wires will now be loose.
8.1.4.
Move the wires away from the two battery terminals, taking care to avoid accidental arcing of the terminals.
8.1.5.
Lift the battery out of the front half of the casing.
8.2.
DISPOSAL
8.2.1.
Take the battery to a recycling centre that handles sealed, lead-acid batteries.
8.2.2.
If there is no recycling centre in the area, contact the local environmental agency for disposal instructions.
9. TROUBLESHOOTING
THE PROBLEM
Unit has been charged
Check charger to see that it is charging.
for 36 hours but there
Charger should be warm.
is no change in the
Check all wire connections
status of the LEDs
Possible defective internal battery.
Charger works well but
still no change in LED
status.
No LEDs come on, but
RoadStart unit battery defective which
when the AC adaptor is
could have been caused by intense use
plugged into the unit
without a cool-down period.
they do.
Roadstart unit is fully
Check where the wires meets the jaw on
charged but delivers no
the unit clamps. Ensure they are well
power.
crimped. Ensure that the safety switch is
in the ON position.
When connecting an
The accessory is drawing too much
accessory via the DC
current, resulting in the internal circuit
outlet there is no
breaker operating. Allow to cool and
power.
reset. Check accessory current draw.
© Jack Sealey Limited
THE SOLUTION
Original Language Version
QUESTION
How many jump
Between 1 and 20 depending upon
starts can a fully
operating factors such as temperature,
charged RoadStart
general condition of the vehicle, engine type
do before needing to
and size.
be recharged?
Yes, in accordance with national and local
Can the RoadStart
authority regulations.
be recycled?
Room temperature. The RoadStart will also
What is the ideal
operate at lower temperatures, its power
in-use storage
however will be lessened. Intense heat will
temperature
activate self-discharge.
of the RoadStart?
I have a regular 10
No. Only the supplied charger can be used.
amp battery charger,
can I use it to
recharge the
RoadStart?
Is the RoadStart fool
No. All jump starting instructions must be
proof?
followed carefully.
Can I replace the
Yes, but note that the batteries are not
internal batteries?
covered by warranty as they are
consumable items
RS132.V5, RS1322HV.V2 Issue 2 (2) 24/06/22
ANSWER
Advertisement
