Bosch Professional GWX 18V-10 P Original Instructions Manual page 10

10 | English
Angle Grinder
Restart protection
Run-out brake
Weight according to EPTA-
B)
Procedure 01:2014
Recommended ambient tem-
perature during charging
Permitted ambient temperat-
C)
ure during operation and
during storage
Compatible rechargeable
batteries
Recommended rechargeable
batteries
Recommended chargers
A) Rated no-load speed for the selection of appropriate grinding
tools in accordance with EN 60745. The actual speed is lower
for safety reasons.
B) Depends on rechargeable battery, protective guard, and auxili-
ary handle in use
C) Limited performance at temperatures < 0 °C
Noise/Vibration Information
Noise emission values determined according to
EN 60745-2-3.
Typically the A-weighted noise level of the power tool are: 82
dB(A); sound power level 93 dB(A). Uncertainty K = 3 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 60745-2-3:
Surface grinding (roughing) and abrasive cutting:
2 2
a = 6.0 m/s , K = 1.5 m/s ,
h
Disc sanding:
2 2
a = 3.0 m/s , K = 1.5 m/s .
h
The vibration level given in these instructions has been
measured in accordance with a standardised measuring pro-
cedure and may be used to compare power tools. It can also
be used for a preliminary estimation of exposure to vibra-
tion.
The stated vibration level applies to the main applications of
the power tool. However, if the power tool is used for differ-
ent applications, with different application tools or poorly
maintained, the vibration level may differ. This can signific-
antly increase the exposure to vibration over the total work-
ing period.
To estimate the exposure to vibration accurately, the times
when the tool is switched off or when it is running but not ac-
tually being used should also be taken into account. This can
significantly reduce the exposure to vibration over the total
working period.
1 609 92A 86W | (30.08.2022)
Implement additional safety measures to protect the oper-
GWX 18V-10 P
ator from the effects of vibration, such as servicing the
●
power tool and application tools, keeping the hands warm,
●
and organising workflows correctly.
kg 2.5–3.3
Kickback control
°C 0 to +35
°C –20 to +50
To restart the tool, set the On/Off switch (6) to the "off" po-
sition and then switch the power tool on again.
GBA 18V...
ProCORE18V...
Restart protection
GBA 18V...
The restart protection feature prevents the power tool from
≥ 4.0Ah
uncontrolled starting after the power supply to it has been
ProCORE18V...
interrupted.
≥ 4.0Ah
To restart the tool, set the on/off switch (6) to the off posi-
GAL 18...
tion and then switch the power tool on again.
GAX 18...
GAL 36...
X-LOCK run-out brake
triggered, the power tool will brake even faster than this.
Drop control
DROP
CONTROL
Rechargeable battery
Bosch sells some cordless power tools without a re-
chargeable battery. You can tell whether a rechargeable bat-
tery is included with the power tool by looking at the pack-
aging.
Charging the battery
Use only the chargers listed in the technical data. Only
u
these chargers are matched to the lithium-ion battery of
your power tool.
Note: Lithium-ion rechargeable batteries are supplied par-
tially charged according to international transport regula-
tions. To ensure full rechargeable battery capacity, fully
charge the rechargeable battery before using your tool for
the first time.
Inserting the Battery
Push the charged battery into the battery holder until it
clicks into place.
If there is a sudden kickback in the power tool,
e.g. jamming in a separating cut, the power
supply to the motor will be interrupted elec-
tronically.
The power tool is fitted with an electronic run-
out brake. When the power supply is switched
off or interrupted, the abrasive tool is brought
to a complete stop within a few seconds. When
Drop Control or Kickback Control are
The integrated impact shutdown switches the
power tool off as soon as it hits the floor. To re-
start the tool, set the on/off switch (6) to the
"off" position and then switch the power tool on
again.
Bosch Power Tools