Bitspower BP-RAMCD5-LN2 Instruction Manual

Bitspower BP-RAMCD5-LN2 Instruction Manual

Universal memory covers for ln2 container ( ddr5, double-sided module )

Advertisement

Bitspower Universal Memory Covers for LN2 Container
( DDR5, Double-sided module )

Accessories

1
M3x8mm Screw
6 PCS
2
Set Screw
6 PCS
3
1 mm Thermal pad
6 PCS
4
RAM Heat Sink
2 SET
5
M2.5x12 Screw
4 PCS
4
2
1
V5
[ 1 ]
instruction manual
3

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the BP-RAMCD5-LN2 and is the answer not in the manual?

Questions and answers

Summary of Contents for Bitspower BP-RAMCD5-LN2

  • Page 1 Bitspower Universal Memory Covers for LN2 Container ( DDR5, Double-sided module ) Accessories M3x8mm Screw 6 PCS Set Screw 6 PCS 1 mm Thermal pad 6 PCS RAM Heat Sink 2 SET M2.5x12 Screw 4 PCS [ 1 ]...
  • Page 2 Bitspower recommends that consumers use the Bitspower Pellucid Coolant for their water-cooling liquid. Also, they can add Bitspower Dye to Pellucid Coolant for the color requirement. If the consumer chooses different water-cooling liquids, the resulting impurities may cause peeling off the coating on some of the hardware, water channels blockage by built-up residue, improper operation of the water pump, water tank tube breakage, and o-rings deformation leading to leakage.
  • Page 3 使用說明書 Bitspower Universal Memory Covers for LN2 Container ( DDR5, Double-sided module ) 配件 M3x8mm 螺絲 6 支 止付螺絲 6 支 1 mm 導熱墊片 6 片 記憶體夾片 2 組 M2.5x12 螺絲 4 支 [ 3 ]...
  • Page 4 注意 跑水前,請先確認所有零件已安裝在正確的位置上,在不開主機,單開水泵的情况下,進行 24 小時的跑水測試, 確保無漏水情况後再開主機,避免發生漏水而導致電腦零件的損壞。 本公司保留對產品的設計更改以及解釋的權力,如有更動恕不另行通知,產品顏色與配件以實物為準。 當使用測氣產品測試水路時 , 為避免由于壓力過大導致產品損壞 , 輸入的壓力請不要超過 0.5kg/cm (Bar), 如因壓力 過大造成產品損壞 , 將由客戶自行承擔 . 嚴禁客戶在水路有水及水泵開啟的情況下進行氣體飽壓測試。 Bitspower 建議消費者使用 Bitspower 透明冷卻液。此外,也可以添加 Bitspower 染料到透明冷卻液中以滿足顏色 要求。如果消費者選擇不同的水冷液,可能會引起水路配件中的塗層剝落、積垢堵塞水道、水泵磨損、水箱管破裂、 破壞 O 型圈密封性導致漏水等。任何因使用不當水冷液導致相關的問題將由消費者自行負責。 [ 4 ]...
  • Page 5 使用说明书 Bitspower Universal Memory Covers for LN2 Container ( DDR5, Double-sided module ) 配件 M3x8mm 螺丝 6 支 止付螺丝 6 支 1 mm 导热垫片 6 片 记忆体夹片 2 组 M2.5x12 螺丝 4 支 [ 5 ]...
  • Page 6 注意 跑水前,请先确认所有零件已安装在正确的位置上,在不开主机,单开水泵的情况下,进行 24 小时的跑水测试, 确保无漏水情况后再开主机,避免发生漏水而导致电脑零件的损坏。 本公司保留对产品的设计更改以及解释的权力,如有更动恕不另行通知,产品颜色与配件以实物为准。 当使用测气产品测试水路时 , 为避免由于压力过大导致产品损坏 , 输入的压力请不要超过 0.5kg/cm (Bar), 如因压力 过大造成产品损坏 , 将由客户自行承担 . 严禁客户在水路有水及水泵开启的情况下进行气体饱压测试。 Bitspower 建议消费者使用 Bitspower 透明冷却液。此外,也可以添加 Bitspower 染料到透明冷却液中以满足颜色 要求。如果消费者选择不同的水冷液,可能会引起水路配件中的涂层剥落、积垢堵塞水道、水泵磨损、水箱管破裂、 破坏 O 型圈密封性导致漏水等。任何因使用不当水冷液导致相关的问题将由消费者自行负责。 [ 6 ]...

Table of Contents