Swann CoreCam - Wireless Security Camera Manual

CAMERA OVERVIEW

Pull rubber cap gently from the bottom to access:

• ON/OFF switch
• MicroSD card slot
  32GB card pre-installed, Max. 128GB card supported
• Micro USB charging port
• Reset button
  • Press and hold for 5 seconds to enter pairing mode
  • Press and hold for 10 seconds to factory reset the camera

GETTING STARTED

Charging the camera

Before using the camera for the first time, fully charge it with the included micro USB charging cable.

1. Pull open the rubber cap on the bottom of the camera.
2. Slide the ON/OFF switch to the ON position. Note: You can also charge the camera with the switch OFF but you won't be able to check the LED indicator for the charging status.
3. Insert the smaller end of the micro USB charging cable into the micro USB port on the camera.
4. Insert the other end of the micro USB charging cable into a USB wall charger such as the USB power adapter for your smartphone.
5. The LED indicator on the front of the camera will turn solid blue indicating that the camera is charging. When the camera is fully charged, the LED indicator will turn off. Actual charging times may vary depending on the USB power supply (DC5V 2.1A is recommended for faster charging) and the remaining battery level. A full charge may take up to 6 hours.
6. After charging is finished, unplug the micro USB charging cable from the camera and make sure to close the rubber cap tightly to keep out water and dust.

Replacing the microSD card

The camera comes with a 32GB microSD card pre-installed for recording events and performing firmware updates. You can easily replace the microSD card with a new one (max. 128GB card supported), if needed in the future. Simply open the rubber cap on the bottom of the camera, eject the current microSD card (push in until it clicks) from the microSD card slot, and then insert the new microSD card (with the label side facing the front of the camera) into the slot until it clicks into place. You should format the microSD card the first time it is used. From the Swann Security app, go to Device Settings > [your camera] > Advanced Settings and tap Format.

GET THE SWANN SECURITY APP

1. Download the latest version of the Swann Security app from the Apple App Store® or Google Play™ Store on your iOS or Android device. Simply search for "Swann Security".
2. Open the app and create your Swann Security account by tapping "Not yet registered? Sign Up" at the bottom of the screen. Then, activate your Swann Security account by confirming the verification email that is sent to the registered email address.
   

SET UP THE CORECAM

Launch the Swann Security app and sign in. Tap the Pair Device button on the screen (or tap the menu icon in the top left and select "Pair Device"). The app will now guide you through the pairing process to set up the camera with your Wi-Fi network.

Before you begin, have the camera with you and be close to your router. Please note that the camera is only compatible with the 2.4GHz network. If your router is using the 5GHz band, please ensure it is operating in mixed mode.

CAMERA PLACEMENT

The camera can be conveniently placed on a table or shelf, or mounted on a flat surface using the included bracket. Because the camera is completely wire-free, you'll have a lot of flexibility on where you can install it. Choose a location with strong, reliable Wi-Fi reception to ensure best video streaming and battery performance. The easiest way to check is to use your smartphone. Connect your smartphone to your Wi-Fi network at the spot you have chosen and see if you get 2 bars of Wi-Fi signal or more. As a general rule, the nearer the camera is to your router, the better the wireless connection quality. If you're finding the wireless signal is too weak or out of range, consider installing a Wi-Fi range extender.

Mounting the bracket
If mounting to a wooden surface, screw bracket directly to the surface. If mounting to a masonry surface (brick, concrete), mark and drill holes, insert wall plugs, and screw bracket to the surface.
Adjusting the viewing angle
Loosen the adjustment ring slightly by turning counter-clockwise. Swivel or tilt the camera as needed then tighten the adjustment ring to lock the position.
Attaching the camera to the bracket
Screw the threaded hole at the bottom of the camera onto the threaded post of the bracket by turning the locking knob clockwise until the camera is securely attached.

HELP AND RESOURCES

Motion detection

The camera's PIR motion sensor detects heat signatures of moving objects. You'll generally get good detection results by pointing the camera downwards at an angle where people will be moving across the coverage area before heading directly towards the camera. You can turn motion detection on or off, as well as adjust the motion detection sensitivity settings using the Swann Security app.

LED indicator guide

The LED light on the front of your camera helps inform you of what is happening with the device.

Rebooting the camera

On rare occasions, it might be necessary to reboot your camera if it becomes unresponsive. A simple reboot can also fix connectivity issues quickly. To reboot the camera, open the rubber cap on the bottom of the camera, slide the ON/OFF switch to the OFF position, wait for 60 seconds, then slide the ON/OFF switch back to the ON position.

Swann Security app manual

To better understand the Swann Security App's interface and features, access the app manual (Menu > User Manual). You can learn about navigating the various app screens to view live camera stream, enable 2-way talk, playback recordings, configure modes, check battery level, and more.

Have questions?
Visit our Support Center at support.swann.com. You can register your product for dedicated technical support, find troubleshooting articles, and more. Or email us at any time via: tech@swann.com