High temp (+660 f/+349 c) pressure probe, 5000 psi, 3 pc/psi, 0.218 in dia. ss diaphragm, accel. comp., 5-point cal ranges at 5kpsi, 500psi and 100psi uht-12 element (18 pages)
Page 1
Installation and Operating Manual This manual contains the 061A01 installation and operating manuals that comprise a Model 112M362 High resolution ICP® pressure probe, 50 psi, 100 mV/psi, 0.218" dia. diaphragm, accel. comp., integral cable kit. For assistance with the operation of this product, contact the PCB Piezotronics, Inc.
Assistance is needed to safely operate equipment PCB Piezotronics is an ISO-9001 certified company whose Damage is visible or suspected calibration services are accredited by A2LA to ISO/IEC Equipment fails or malfunctions 17025, with full traceability to SI through N.I.S.T.
Page 3
CAUTION Refers to hazards that could damage the instrument. NOTE Indicates tips, recommendations and important information. The notes simplify processes and contain additional information on particular operating steps. The following symbols may be found on the equipment described in this manual: This symbol on the unit indicates that high voltage may be present.
OPERATION MANUAL FOR ® PRESSURE SENSORS Models 102A02, A05, A07, A09 Models 112A21, A22, A23 Models 112A21, 112A22 and 112A23 are in the INTRODUCTION basic probe configuration as shown in Figure 1, and are installed with a hollow clamp nut with 5/16-24 The series of miniature pressure sensors described by external threads.
OPERATION MANUAL FOR ® PRESSURE SENSORS Models 102A02, A05, A07, A09 Models 112A21, A22, A23 Models 102A02, 102A07, and 102A09 utilize the A silicone rubber coating approximately .010" thick same inner probe design but in a 3/8-24 threaded has also been proven effective in many applications. adaptor with floating clamp nut to allow adjustment General Electric RTV type 106 silicone rubber is of diaphragm depth where it is necessary to adapt to...
Page 8
OPERATION MANUAL FOR ® PRESSURE SENSORS Models 102A02, A05, A07, A09 Models 112A21, A22, A23 Defined for practical purposes as the minimum For the shorter discharge time constant series, a rapid readout signal, the resolution is based on the pressure step must be generated by a pneumatic sensitivity of 50 mV/psi and a low noise amplifier of pressure pulse calibrator or dead weight tester and 50 V peak noise.
Models 102A02, A05, A07, A09 Models 112A21, A22, A23 MAINTENANCE The miniature size sealed construction precludes field maintenance. Should service be required, return unit to factory with note describing problem. ICP is a registered trademark of PCB Piezotronics Drawing Number: 21070 Revision: NR...
Page 10
Model Number Revision: B ICP® PRESSURE SENSOR 112M362 ECN #: 45139 Performance ENGLISH OPTIONAL VERSIONS Measurement Range(for ±5V output) 50 psi 345 kPa Optional versions have identical specifications and accessories as listed for the standard Useful Overrange(for ± 10V output)
Page 11
Mounting adaptor, 3/8-24 external thd to 5/16-24 internal thd, 17-4 SS (for Series 111, 112 & 113) Installation and Operating Manual For assistance with the operation of this product, contact the PCB Piezotronics, Inc. Toll-free: 716-684-0001 24-hour SensorLine: 716-684-0001 Fax: 716-684-0987 E-mail: info@pcb.com...
Page 12
Assistance is needed to safely operate equipment PCB Piezotronics is an ISO-9001 certified company whose Damage is visible or suspected calibration services are accredited by A2LA to ISO/IEC Equipment fails or malfunctions 17025, with full traceability to SI through N.I.S.T.
Page 13
CAUTION Refers to hazards that could damage the instrument. NOTE Indicates tips, recommendations and important information. The notes simplify processes and contain additional information on particular operating steps. The following symbols may be found on the equipment described in this manual: This symbol on the unit indicates that high voltage may be present.
Page 15
Component Name Hazardous Substances Lead (Pb) Mercury (Hg) Cadmium (Cd) Chromium VI Polybrominated Polybrominated Compounds Biphenyls (PBB) Diphenyl Ethers (Cr(VI)) (PBDE) Housing PCB Board Electrical Connectors Piezoelectric Crystals Epoxy Teflon Electronics Thick Film Substrate Wires Cables Plastic Solder Copper Alloy/Brass This table is prepared in accordance with the provisions of SJ/T 11364.
Page 16
PCB Piezotronics Inc. claims proprietary rights in REVISIONS the information disclosed hereon. Neither it nor any reproduction thereof will be disclosed to others DESCRIPTION without the written consent of PCB Piezotronics Inc. UPDATED NOTES & ADDED DETAIL VIEW 53692 ELECTRICAL CONNECTOR COAXIAL...
Page 17
Installation and Operating Manual This manual contains the 061A01 installation and operating manuals that comprise a Model 112M362 High resolution ICP® pressure probe, 50 psi, 100 mV/psi, 0.218" dia. diaphragm, accel. comp., integral cable kit. For assistance with the operation of this product, contact the PCB Piezotronics, Inc.
Page 18
Assistance is needed to safely operate equipment PCB Piezotronics is an ISO-9001 certified company whose Damage is visible or suspected calibration services are accredited by A2LA to ISO/IEC Equipment fails or malfunctions 17025, with full traceability to SI through N.I.S.T.
Page 19
CAUTION Refers to hazards that could damage the instrument. NOTE Indicates tips, recommendations and important information. The notes simplify processes and contain additional information on particular operating steps. The following symbols may be found on the equipment described in this manual: This symbol on the unit indicates that high voltage may be present.
Page 21
Component Name Hazardous Substances Lead (Pb) Mercury (Hg) Cadmium (Cd) Chromium VI Polybrominated Polybrominated Compounds Biphenyls (PBB) Diphenyl Ethers (Cr(VI)) (PBDE) Housing PCB Board Electrical Connectors Piezoelectric Crystals Epoxy Teflon Electronics Thick Film Substrate Wires Cables Plastic Solder Copper Alloy/Brass This table is prepared in accordance with the provisions of SJ/T 11364.
Page 22
PCB Piezotronics Inc. claims proprietary rights in REVISIONS the information disclosed hereon. Neither it nor any reproduction thereof will be disclosed to others DESCRIPTION without the written consent of PCB Piezotronics Inc. REMOVED SEAL, UPDATED MOUNTING TORQUE 45222 CABLE: SEE SPECS...
Need help?
Do you have a question about the 112M362 and is the answer not in the manual?
Questions and answers