Office Star Products Pro-Line II 92893 - Manager's Chair Operating Manual

FEATURES

• PNEUMATIC SEAT HEIGHT ADJUSTMENT
  To raise seat remove pressure from seat and pull lever (4) up.
  To lower seat height sit on chair and pull lever (4) up.
• SEAT ANGLE ADJUSTMENT
  To adjust seat angle, lift lever (2). Leave lever up for free float or push lever (2 ) down to lock.
• BACKREST ANGLE ADJUSTMENT
  To adjust back angle lift lever (1). Leave lever (1) up for free float or push lever (1) down to lock at any angle.
• SEAT SLIDER ADJUSTMENT
  To slide seat forward or backward, pull handle bar (3) out.
  Release handle bar (3) to lock desired seat position.
• TILT TENSION ADJUSTMENT
  To adjust title tension, Turn knob (6) clockwise to increase tension and counter-clockwise to decrease or ease the tension.
• SEAT/BACK ANGLE ADJUSTMENT & FORWARD TILT
  To adjust Seat/Back angle, lift lever (2) leave lever up for free float or push lever down to lock. For forward tilt lean back with lever (2) in the down position and push lever (5) forward. Lift lever (2) and the seat willl tilt forward for keyboard intensive activities.
• ARM HEIGHT ADJUSTMENT
  To adjust arm height, push buttom (7) to allow the arms to move up or down freely. Release buttom (7) once the desired height is reached.
• ARM WIDTH ADJUSTMENT
  To adjust arm width, loosen knob (8) to allow the arms to move in and out freely. tighten knob (8) once the desired width is reached.

WARNING

1. Use this product only one person at a time.
2. Do not use this chair unless all bolts screws and knobs are securely tightened.
3. Check that all bolts screws and knobs are tight every three months or as needed.
4. Do not overturn back tilt knob when decreasing tension.
5. Dispose of packing material properly. Do not use plastic cover as head covering. It may cause suffocation.
6. Do not use chair as a stepladder.
7. Use this chair for its intended purpose only.
8. Use mild detergent only for cleaning.

ASSEMBLY INSTRUCTIONS

Remove all the parts from carton, separate them into part numbers indicated on the list and make sure part quantities are correct.

1. Insert five Casters (2) into Base (1), push hard until you hear or feel Caster (2) snap into place. Insert Pneumatic Cylinder (3) into Base (1) and slip Bellows (4) over Pneumatic Cylinder (3).
2. Attach Arms (8L & 8R) to Seat Cushion (7) using one Knob (9), one Flat Washer (10) and one Lock Washer (11) for each Arm (8). FULLY TIGHTEN KNOBS (9).
3. Attach Mechanism (5) to Seat Cushion (7) using six Mechanism Screws (12). FULLY TIGHTEN ALL MECHANISM SCREWS (12).
   NOTE: To access all screws, you will need pull lever (3) out to adjust Seat Slider.
4. Attach Back Support (17) to Backrest (6) using Back Support Screws (13). FULLY TIGHTEN BACK SUPPORT SCREW (13).
5. Insert Back Support (17) into rear of Mechanism (5) and secure using Back Mounting Screw (15), one Flat Washer (10) and one Lock Washer (11). Secure Back Support Cover (16) over Back Support (17) using two Back Cover Screws (14), FULLY TIGHTEN ALL SCREWS.
6. Place the assembled seat on top of Pneumatic Cylinder (3) and apply pressure.

ATTENTION: MAKE SURE ALL SCREWS ARE FULLY TIGHTENED BEFORE USING CHAIR.

© Office Star Products January 2012

Documents / Resources

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download Office Star Products Pro-Line II 92893 - Manager's Chair Operating Manual