Return the machine to the nearest authorized Baby Lock retailer for examination, repair, electrical or mechanical adjustment. Always unplug the machine from the electrical outlet when making any •...
Page 4
In the event a malfunction occurs or adjustment is required, first follow the and cause it to break. troubleshooting table in the back of the Instruction and Reference Guide to inspect and adjust the machine yourself. If the problem persists, please consult your local authorized Baby Lock retailer.
Page 5
CAUTION FOR USERS IN COUNTRIES EXCEPT EUROPEAN COUNTRIES This appliance is not intended for use by persons (including (For U.S.A. only) children) with reduced physical, sensory or mental This appliance has a polarized plug (one blade wider than the other). To reduce the risk of electrical shock, this plug is intended to fit in a polarized capabilities, or lack of experience and knowledge, unless electrical outlet only one way.
Page 6
• If the available electrical outlet is not suitable for the plug supplied with this equipment, you should contact your authorized Baby Lock retailer to obtain the correct lead. CAUTION Moving parts -To reduce risk of injury, disconnect from supply circuit before servicing.
Before You Begin (1) Power Cord and Foot Controller Handwheel WARNING ● Position needle using handwheel. Please use common household ✽ Always turn handwheel towards current. you. ● Attach power cord. Power Cord CAUTION Handwheel ● Insert foot controller jack into machine. ●...
Presser Foot Lever Presser Foot Pressure Presser Foot Pressure Adjustment Dial Adjustment Dial ● Lowering the presser foot lever lowers the sewing foot down ● Turning the pressure adjustment onto the fabric and engages the dial raises and lowers the thread tension function.
Before You Begin (2) Thread Cutter Button Feed Dog Adjustment Knob CAUTION ● Height of feed dog can be adjusted to coincide with fabric weights. When the machine stops due to jammed threads and so forth, do not press on the foot controller; Thread Cutter Button turn power off, and move the needle with the handwheel to...
Changing Needles CAUTION Changing the Feed Pin • Please make sure the power to the machine is turned off before carrying 1 Set the feed dog to the “velvet” out the following operations. There is a chance of injury if the machine position.
Winding/Installing the Bobbin Bobbin Winding Spool Cap Spool Cone Holder Spool of Thread 5679<A 1 Raise the thread guide bar all the way. Note 2 Mount a spool of thread on the spool pin. Do not move bobbin winding clutch while machine is running.
Page 15
Press down Pedal Foot controller Bobbin Winding Clutch Place the thread end so that it does Pressing down on the foot controller not protrude from the bobbin. harder increases the winding speed. 7 While holding the end of the thread, 8 Start winding the bobbin again 9 Stop winding process when bobbin 0 Manually move bobbin winding...
Baby Lock retailer. Rotate the handwheel one full rotation at that length. Following this process towards you to check that the bobbin case eliminates the need to manually pull the is set securely.
Upper Threading CAUTION Turn off the power to the machine before threading the upper thread. Otherwise, it may cause injuries if you unintentionally press down on the foot controller. Upper Threading When using strong thread such as synthetic thread, pass the thread through all holes (*1).
Upper Threading for Thick Fabrics or When Using Heavier Threads For a tighter upper thread, such as when sewing thick fabrics or using heavier threads, thread the machine as described below. 1 Refer to page 15 to 2 Pass the thread through 5 Pass the thread through 7 Pass the thread thread the three-holed...
CAUTION Be sure to turn off the power before using the needle threader. There is a risk of injury if you accidentally step on the foot controller. ✽ The needle threader can be used with machine needles #11 through #16. Using the Needle Threader When using #9 needles or thinner, manually thread the needle.
Stitch Samples and Needle Chart ✽ Bobbin thread should feed smoothly. Adjust bobbin thread Stitch Samples Thread Tension to match that of upper thread. (If bobbin thread is too tight it may cause fabric to bunch up.) 1 Set stitch length regulator to Correct thread tension Wrong side of fabric to increase...
Changing Presser Feet CAUTION ✽ Use presser feet supplied with your machine. Each foot is Presser Feet specially designed for this machine and has clearance for the pin at the rear of each foot. Make sure the power to the machine is off before changing presser feet. ●...
Basic Sewing (1) Basic Sewing 8 When changing sewing directions. Finish Backstitches Begin sewing. Before 1 cm sewing. sewing. 1 cm 1 Raise presser foot, pull 2 Lower presser foot lever to ✽ At the beginning and end 4 Raise needle to highest position. 1 Make sure needle is pierced 5 Raise presser foot, remove about 15 cm (approx.
Basic Sewing (2) CAUTION Make sure the power to the machine is off before changing presser feet. 5 With your right hand, put the Rolled Hem Foot edge of the rolled hem under the presser foot, from the spot 1 Attach rolled hem foot. Thread where the threads come out.
Basic Sewing (3) CAUTION 5 Secure the zipper with basting and sew along the mark. Make sure the power to the machine is off before changing feet. CAUTION ✽ When attaching zippers to stretch fabrics, use the pin feed method and adjust foot pressure accordingly.
Invisible Zipper Foot 1/4” Foot Teeth 1 Attach invisible zipper foot. ● Sewing machine settings: 2 Align zipper with fabric. Mark Stitch length = 2 - 2.5 mm Seam allowance the base of the opening (1/4”, 6.4 mm) Baste approximately 2 cm (approx. •...
Free-Motion Quilting Foot Seam Guide Reduce the foot pressure (page 9) 1 Tighten the screw securely and turn the feed dog adjustment knob with a screwdriver since it (page 10) on the machine lowering might otherwise loosen due to the feed dog for free-motion quilting. vibration.
Caring for Your Machine Cleaning the Machine Lubrication Points ● When using the sewing machine CAUTION every day, apply a few drops of oil* to each location indicated Make sure the power to the twice a month. machine is off before cleaning sewing machine.
Trouble Shooting ✽ Before taking your sewing machine in for service, check the following chart. Improper fabric/needle/ Upper threading is not Upper thread tension is Thread Thread is getting tangled. Bobbin case may be scratched. thread combination. threaded correctly. too high. Breakage Re-thread machine.
Needle is not attached Needle is bent, or tip is Handwheel Thread is getting tangled. correctly. dull. Doesn’t Rotate Re-thread machine. Clean bobbin case and under Change needle. Reattach. 14-17.25 needle plate. Oil the machine. Thread Gets Upper threading is not Upper thread tension is Bobbin case may be scratched.
été endommagée, ou en cas de contact avec de l’eau. Renvoyez-la - Pour au revendeur Baby Lock agréé le plus proche à des fins d’examen, de réduire les risques de brûlure, d’incendie, d’électrocution ou de blessures. réparation ou de réglage électronique ou mécanique.
Page 31
• Lors d’un dysfonctionnement ou d’un réglage, suivez d’abord le tableau de dépannage à la fin du manuel d’instructions pour inspecter et régler la machine vous-même. Si le problème persiste, veuillez consulter votre revendeur Baby Lock local agréé.
Page 32
ATTENTION POUR LES UTILISATEURS DES PAYS HORS EUROPE Cet appareil n’est pas conçu pour une utilisation par des (Pour les États-Unis uniquement) personnes (adultes ou enfants) souffrant d’incapacités Cet appareil possède une fiche polarisée (une lame plus large que l’autre). Pour réduire les risques de choc électrique, cette fiche est prévue pour rentrer dans une prise physiques, sensorielles ou mentales, ou ne disposant pas électrique polarisée dans un seul sens.
Page 33
POUR LES UTILISATEURS SIGNE D’AVERTISSEMENT Le signe d’avertissement suivant se trouve sur la machine. AU ROYAUME-UNI, EN Veillez à bien observer les mesures de précaution décrites IRLANDE, À MALTE ET À sur ce signe. CHYPRE UNIQUEMENT IMPORTANT • En cas de remplacement du fusible de la fiche, utilisez un fusible certifié ASTA à...
Page 34
TABLE DES MATIÈRES INTRODUCTION ................. 28 Utilisation du filet de la bobine ........44 INSTRUCTIONS DE SÉCURITÉ IMPORTANTES ..... 28 Points d’essai et tableau d’aiguilles ........45 Accessoires................33 Points d’essai ............45 Fonctions de la machine ............34 Tension des fils ............45 Avant de commencer (1) ............
Fonctions de la machine Barre de guidage du fil (Page 39) Guide-fil (droit) Poignée Guide-fil de bobinage (Page 42) de la canette (Page 39) Molette de réglage de la Bobineur de canette Guide-fils à trois pression du pied-de-biche (Page 39) trous (Page 42) Sélecteur de longueur Levier du...
Avant de commencer (1) Cordon d’alimentation et pédale Volant AVERTISSEMENT ● Positionnez l’aiguille à l’aide du volant. Utilisez un courant secteur ✽ Toujours faire tourner le volant domestique ordinaire. vers soi. ● Branchez le cordon d’alimentation. Cordon ATTENTION Volant d’alimentation ●...
Molette de réglage de Levier du pied-de-biche Molette de réglage de la la pression du pied-de-biche pression du pied-de-biche ● Abaissez le levier du pied-de- biche pour abaisser le pied sur ● Tournez la molette de pression le tissu et activer la fonction de pour faire monter ou descendre tension du fil.
Avant de commencer (2) Touche coupe-fil Bouton de réglage des griffes d’entraînement ATTENTION ● Il est possible de régler Si la machine s’arrête, notamment en la hauteur des griffes cas de bourrage de fils, ne pas appuyer d’entraînement en fonction du sur la pédale ;...
Remplacement de l’aiguille ATTENTION Remplacement de l’ergot d’entraînement • Bien éteindre la machine à coudre avant d’effectuer les opérations suivantes. Sinon, la machine risque de se mettre en marche accidentellement et de 1 Réglez les griffes d’entraînement sur la provoquer des blessures. position « velours ».
Bobinage/installation de la canette Remplissage de la canette Broche porte-bobine Couvercle de bobine conique 5679<A Bobine de fil 1 Relevez la barre de guidage du fil au maximum. Remarque 2 Placez une bobine de fil sur le porte-bobine. Ne pas déplacer la butée de canette 5 - A: Voir les illustrations suivantes.
Page 42
Appuyer Pédale de rhéostat Butée de canette Placez l’extrémité du fil de façon qu’il Si vous appuyez plus fort sur la pédale, ne ressorte pas de la canette. la vitesse de bobinage augmente. 7 Tout en tenant l’extrémité du fil, 8 Recommencez à...
également être commandé auprès de provoquer des ruptures du fil inférieur. Tournez le à une longueur appropriée après le votre détaillant Baby Lock. volant d’un tour complet vers soi pour s’assurer remplacement de la canette et le garde que le boîtier de la canette est bien en place.
Enfilage supérieur ATTENTION Coupez l’alimentation électrique de la machine avant d’enfiler le fil supérieur. Sinon, vous pourriez vous blesser en appuyant sur la pédale par inadvertance. Enfilage supérieur Quand vous utilisez un fil robuste tel qu’un fil synthétique, faites passer le fil dans tous les trous (*1).
Enfilage supérieur pour tissus épais ou lors de l’utilisation de fils plus épais Pour un fil supérieur plus tendu, comme quand vous cousez des tissus épais ou utilisez des fils plus épais, enfilez la machine comme décrit ci-dessous. 1 Reportez-vous à la 2 Faites passer le fil dans le 5 Faites passer le fil dans 7 Faites passer le fil...
ATTENTION Veillez à bien couper l’alimentation électrique avant d’utiliser l’enfile-aiguille. Vous risquez de vous blesser si vous appuyez accidentellement sur la pédale. ✽ Vous pouvez utiliser l’enfile-aiguille avec des aiguilles #11 à #16. Utilisation de l’enfile-aiguille Quand vous utilisez des aiguilles #9 ou plus fines, enfilez l'aiguille manuellement. Enfile-aiguille 1 Veillez à...
Points d’essai et tableau d’aiguilles ✽ Le fil de canette doit être alimenté régulièrement. Réglez le Points d’essai Tension des fils fil de canette en fonction de la tension du fil supérieur. (Si le fil de canette est trop serré, le tissu risque de se plisser.) 1 Réglez le sélecteur de longueur de Corriger la tension du fil.
Changement du pied-de-biche ATTENTION ✽ Utilisez les pieds-de-biche fournis avec votre machine. Les différents pieds-de-biche Chaque pied a été spécialement conçu pour cette machine et possède au dos l’espace nécessaire pour Bien éteindre la machine avant de changer le pied-de-biche. la tige.
Couture de base (1) Couture de base 8 Pour modifier le sens de la couture Fin de la Points arrière Commencer couture. Avant de 1 cm à coudre. coudre. 1 cm 1 Soulevez le pied-de- 2 Abaissez le levier pour ✽...
Couture de base (2) ATTENTION Bien éteindre la machine avant de changer le pied-de-biche. 5 De la main droite, placez le Pied pour ourlet roulotté bord de l’ourlet roulotté sous le pied-de-biche, au point où 1 Fixez le pied pour ourlet roulotté. les fils ressortent.
Couture de base (3) ATTENTION 5 Faufilez la fermeture à glissière pour la fixer puis coudre le long Bien éteindre la machine avant de changer le pied-de-biche. du trait. ✽ Pour coudre une fermeture à glissière sur un tissu extensible, utiliser la méthode ATTENTION d’entraînement par ergots, et régler la pression du pied en conséquence.
Pied pour fermeture à Pied 1/4"/pouce Dents glissière invisible ● Réglages de la machine à coudre : Rentré 1 Fixez le pied pour fermeture à Longueur de point = 2 - 2,5 mm (1/4"/pouce, 6,4 mm) Faufiler glissière invisible. 2 Disposez la fermeture à glissière Base de •...
Pied pour quilting (courtepointe) Guide de couture en mouvement libre 1 Serrez la vis avec un tournevis sinon elle pourrait se desserrer Réduisez la pression du pied (page 36) en raison des vibrations. et tournez le bouton de réglage des griffes d’entraînement (page 37) sur la machine en abaissant les griffes d’entraînement pour le quilting (courtepointe) en mouvement libre.
Entretien de la machine à coudre Nettoyage de la machine Points de graissage ● Lors d’un usage journalier de la ATTENTION machine, appliquez quelques gouttes d’huile* à chaque emplacement Bien éteindre la machine avant indiqué, deux fois par mois. de procéder au nettoyage de la machine à...
Dépannage ✽ Avant de faire réparer la machine à coudre, vérifier le tableau suivant. Vous pouvez résoudre vous-même la plupart des problèmes. Le fil supérieur n’est pas La tension du fil supérieur Mauvaise combinaison Il est possible que le boîtier Rupture Le fil s’emmêle.
La pédale doit être remplacée ou la machine réparée. Contactez votre Le voyant indicateur clignote lentement en continu. revendeur Baby Lock. ✽ La machine ne fonctionnera pas pendant environ 1 seconde immédiatement après la mise sous tension ou après l’insertion ou le retrait de la prise de la pédale.