5 . HOLD key 6 . LINE 1 key 7 . LINE 2 key 8 . MUTE key 9 . Speakerphone key 10 . Line in 11 . DC 5V Bottom of phone 3500SERIES VOIP USER GUIDE: CETIS SIP 2020 www.telematrix.net...
4 . Redial 5 . Mute 6 . Volume Above is a graphical representation of which buttons on the handset correspond to which on the base for the 3500IP trimline phone . www.telematrix.net 3500SERIES VOIP USER GUIDE: CETIS SIP 2020...
The phone will either download its config file as information . By using the Mass Configuration <macaddress> .cetis .cfg or, if that file is not found, utility tools, you can ensure that the substitution the phone will produce a audio prompt (“doodle- of values is not subject to human error that may doodle”) tone as well as flashing lights to prompt...
7 . Voicemail message 8 . Configurable via common browsers 9 . Remote management function 10 . Classification management for common This Cetis SIP endpoint device is SIP 2 .0 compliant user’s password and super-user’s with RFC 3261, and some configuration is password necessary before using the phone .
Hold . 2 . Call Park feature Enable Call Park feature and the Hold key can be used as a Park key (see below) . 3500SERIES VOIP USER GUIDE: CETIS SIP 2020 www.telematrix.net...
. connect user B with user C . Automatic registration: Place the handset in the cradle of the base . The Message light begins to www.telematrix.net 3300 SERIES VOIP USER GUIDE: CETIS SIP 2017...
. For example, Line 1 can place a call from the base phone to one phone destination while Line 2 from the cordless handset can be active to a separate destination . 3300 SERIES VOIP USER GUIDE: CETIS SIP 2017 www.telematrix.net...
Set the primary DNS IP address . 802 .1x_Enable Enable or disable 802 .1x Secondary DNS Set the secondary DNS IP authentication . address . 802 .1x_UserName 802 .1x User name . www.telematrix.net 3300 SERIES VOIP USER GUIDE: CETIS SIP 2017...
WAN port unaltered (unless QoS settings are specified, see appropriate section) to the access switch . • NAT—The WAN port address is used to translate IP connections of devices that are connected to the WAN . 3300 SERIES VOIP USER GUIDE: CETIS SIP 2017 www.telematrix.net...
You can adjust sound and volume settings, set SIP Backup Set the IP address of the codecs and ring types and international signal Server Backup SIP server standards on this page . www.telematrix.net 3300 SERIES VOIP USER GUIDE: CETIS SIP 2017...
Detector function . VAD can reduce RTP data to not send silence packet . Default is Enabled . Enable or disable Comfort Noise Generation when silence is detected in the conversation . 3300 SERIES VOIP USER GUIDE: CETIS SIP 2017 www.telematrix.net...
3.3.4 DIALING RULES fail . You can manage your dial rules on this page . You can remove the option of sending digits www.telematrix.net 3300 SERIES VOIP USER GUIDE: CETIS SIP 2017...
So dialing 3004 would immediately Port number . send those digits to the SIP PBX Check Interval Set check interval time . The and dial without a delay . unit is second . 3300 SERIES VOIP USER GUIDE: CETIS SIP 2017 www.telematrix.net...
VLAN . Example: * * 8 7 * 1 2 3 * 0 # will disable server to be re-directed to for VLAN and should allow the phone to receive a configuration file download . www.telematrix.net 3300 SERIES VOIP USER GUIDE: CETIS SIP 2017...
If found, it will compare its each day . The ConfigID field would be expressed existing model and firmware as the number . Example: 3001 .cetis .cfg would to the firmware files listed in be expressed as 3001 . The filetype and suffix of the .txt file and upgrade or...
. Server Port Set system log server’s port number . Default port is Local Time Manually configure time when 49494, but is User Definable . SNTP is disabled . www.telematrix.net 3300 SERIES VOIP USER GUIDE: CETIS SIP 2017...
CORDLESS TELECOMMUNICATIONS Keypad Set the password of keypad . Password Default is 123 . DECT cordless technology is used in Cetis SIP Verify Enter the new keypad phones and both Power levels and Country codes Password password again for verification .
Setting LLDP up is as simple as leaving the Feature allows a second person to default settings in place on the Cetis phone . share the line from another However, the POE switch must have LLDP turned cordless handset . This can...
1 . Log into phone’s webUI . for VLAN DSCP in VoIP) . Used to provide VLAN 2 . Go to Network Settings > WAN Settings . QOS priority information to the phone (values 1-7) . 3300 SERIES VOIP USER GUIDE: CETIS SIP 2017 www.telematrix.net...
. To fix this you can use LLDP, option 132, or Cetis phones will request options 60/43, 66, 43, statically with **87*123*<vlanID> . 132, and 133 even with a static IP address (via 4.4 QuickKey DialPad Shortcuts...
Page 25
VLAN and should allow the phone to receive a DHCP address from the local network segment . Any other valid number for a VLAN ID (1-4095) will set the VLAN ID to that number . 3300 SERIES VOIP USER GUIDE: CETIS SIP 2017 www.telematrix.net...
2 . This device must accept any interference work is required . Opening or removing received, including interference that may covers may expose you to dangerous cause undesired operation . www.telematrix.net 3500SERIES VOIP USER GUIDE: CETIS SIP 2020...
Page 27
. compliance could void the user’s authority to The termination on an interface may consist operate the equipment . 3300 SERIES VOIP USER GUIDE: CETIS SIP 2017 www.telematrix.net...
Page 28
Any changes made by the user not approved by service may be required . But if advance notice is the manufacturer can void the user’s authority to not practical, the telephone company will notify operate the telephone . www.telematrix.net 3300 SERIES VOIP USER GUIDE: CETIS SIP 2017...
Page 29
. TeleMatrix product warranty information is available at www .telematrix .net . This telephone is hearing aid compatible . 3300 SERIES VOIP USER GUIDE: CETIS SIP 2017 www.telematrix.net...