Related Manuals for Knox STATIONVAULT
Summary of Contents for Knox STATIONVAULT
- Page 1 STATIONVAULT ™ INSTALLATION GUIDE 1601 W. DEER VALLEY ROAD, PHOENIX, AZ 85027 | 800.704.0889 | TECHSUPPORT@KNOXBOX.COM | OPE-SVHWDR-0560-C...
-
Page 2: Fcc Notice
™ INSTALLATION GUIDE Copyright® 2023 by the Knox Company. All rights reserved. The Knox® Company, the Knox logo, and all other Knox Company product or service names are registered trademarks or trademarks of the Knox Company. THE KNOX COMPANY 1601 W. Deer Valley Road Phoenix, AZ 85027 USA... - Page 3 Industrial cellular router doit être installé et utiliséavec une distance minimale de 20cm entre leradiateur & votre corps. For patent information on this product, please visit ip.knoxbox.com 1601 W. DEER VALLEY RD. PHOENIX, AZ 85027 800.704.0889 TECHSUPPORT@KNOXBOX.COM KNOXBOX.COM PAGE 3 ©Knox Company. All rights reserved. OPE-SVHWDR-0560-C...
-
Page 4: Specifications
STATIONVAULT ™ INSTALLATION GUIDE OVERVIEW The Knox StationVault is designed for storage of narcotics and other valuable or controlled items in a facility. Package contents: • StationVault • Three (3) acrylic shelves • Six (6) Shelf pins • One (1) Counter protector / base •... -
Page 5: Getting Started
Add users to the device - only users whose PINs have been added to the device will have access 4. Use the Knox Device Sync App on a PC and the USB 2.0 Cable A Male to Mini B Male (included) to transfer setting into the device 5. -
Page 6: Tools And Hardware
THIS INSTALLATION REQUIRES TWO PEOPLE! INSTALLING THE STATIONVAULT CAUTION: THE STATIONVAULT MUST BE SECURED TO A WALL OR COUNTERTOP TO PREVENT TIPPING. INJURY CAN OCCUR IF INSTALLATION INSTRUCTIONS ARE NOT THOROUGHLY FOLLOWED. READ ALL INSTALLATION INSTRUCTIONS BEFORE MOUNTING. PREPARING THE STATIONVAULT: From the outside of the unit, drill through mounting divots on the base and/or back of the unit to create mounting holes appropriate for your installation. - Page 7 5. Install screws so that the fasteners/nuts are inside the unit 6. Open and close door to ensure it swings freely 1601 W. DEER VALLEY RD. PHOENIX, AZ 85027 800.704.0889 TECHSUPPORT@KNOXBOX.COM KNOXBOX.COM PAGE 7 ©Knox Company. All rights reserved. OPE-SVHWDR-0560-C...
- Page 8 Connecting to Network The StationVault has a concealed antenna which is included in all models and an RJ45 Ethernet port. The device must connect at least periodically to KnoxConnect to obtain firmware and PIN updates and transmit audit history.
-
Page 9: Maintenance And Repair
Many StationVault repairs can be conducted by obtaining a replacement part. However, some repairs will require door and a return to Knox. REMOVING THE DOOR Please contact Knox Customer Service to obtain a RMA and shipping package prior to returning to Knox. Prior to starting: •... -
Page 10: Replacing The Circuit Board
Remove the adhesive release backing from the new light strip 8. Align the free end of the new strip on the StationVault wall behind the hinge, even with the top hinge screw 9. Press firmly to adhere 10. - Page 11 3. Force a sync with KnoxConnect to update the time clock INITIALIZING IN KNOXCONNECT Upon initial installation or to resume use of your StationVault after a circuit board swap, you must establish or re-establish users, user PINs, and device settings for your device in KnoxConnect. Please refer to the Knox Networking Guide and KnoxConnect Admin Guide to complete this setup before continuing.
- Page 12 Connect the MedVault to the computer using the USB cable supplied with your original MedVault and insert the Mini-USB connector into the port on the front of the door Launch the KnoxDevice Sync app to push the network configuration to the StationVault and follow the prompts on the pop-up screen...
Need help?
Do you have a question about the STATIONVAULT and is the answer not in the manual?
Questions and answers