Bauer 20204L-B, 57932 - 16 Ft. Tile/Flooring Laser Level Manual

IMPORTANT SAFETY INFORMATION

WARNING SYMBOLS AND DEFINITIONS

	This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.
	Indicates a hazardous situation which, if not avoided, will result in death or serious injury.
	Indicates a hazardous situation which, if not avoided, could result in death or serious injury.
	Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
	Addresses practices not related to personal injury.

Safety Warnings and Precautions

Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

13. Do not attempt to charge batteries
14. Have the Laser Level calibrated by a qualified technician every year to maintain accurate results.
15. People with pacemakers should consult their physician(s) before use. Electromagnetic fields in close proximity to heart pacemaker could cause pacemaker interference or pacemaker failure.
16. The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator.

SAVE THESE INSTRUCTIONS.

Specifications

Setup - Before Use

Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product.

Functions

Operating Instructions

Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product.

General Operation

1. Install batteries as described in "Battery Replacement".
2. Set the Level on a flat, level surface.
3. To mark guidelines:
   1. Place the bottom on the Level on the floor or wall. Press the Power Switch to turn on the laser.
   2. Place the T-Edge against a wall so that the laser lines run parallel to reference lines.
      

3. If on the wall, align the Level so that the 0° Alignment Bubble is level and the 90° Alignment Bubble is at the top.
   
4. If on the floor, align the Level so that both Alignment Bubbles are level.
   

4. To lay tiles on the floor:
   1. Position Level in a corner so that laser lines run parallel to the reference lines as shown in Step 3.
   2. Lay the first tile so that the sides are flush with the 0° and 90° laser lines.
   3. If laying next to an edge, position the Level so that the T-Edge is against the side of the edge. The 90° laser line should run parallel to the edge and the 0° laser line marks the tile row.
      

5. To apply tiles to a wall:
   1. Determine the height at which the first tile row should begin and mark the wall using the ruler on the Level or other measuring device.
   2. Place the T-Edge at the mark and straighten the Level so that the 0° laser line is parallel with the floor.
      

6. To check the alignment of a row of tiles, place L-Edge at the corner of a tile.
   

7. To check the alignment of a single tile, place the Level's edge on top of the tile as shown below.
   

8. When finished with the Level, press the Power Switch to turn it OFF. Store Level in a dry indoor area away from children, If storing for a long period, remove the batteries.

Maintenance and Servicing

Procedures not specifically explained in this manual must be performed only by a qualified technician.

Cleaning, Maintenance, and Lubrication

1. Wipe unit with a dry, lint-free cloth. Do not use solvents or abrasives.
2. Remove batteries if not in use for long periods.
3. Store unit in a dry location.

4. Other than the batteries, there are no replaceable parts on this unit. Repairs should be done by a qualified technician.

Battery Replacement

1. Turn the Level's Power Switch OFF.
2. Remove battery cover by pressing the Latch and removing the cover.
3. Remove old batteries. Replace with new AA batteries follow polarity.

4. Replace battery cover and be sure the Latch connects securely.

Note: Do not install old and new batteries together. Do not install alkaline, carbonzinc or rechargeable batteries together. Position batteries in proper polarity. Do not use swollen or leaking batteries.

Calibration

Have the Laser Level calibrated by a qualified technician every year.

Record Serial Number Here:
Note: If product has no serial number, record month and year of purchase instead.

Note: Replacement parts are not available for this item.
Reference UPC 193175427045.