Table of Contents
Advertisement
00078A DVD-V72K/XSA-GB4
6/25/02 11:44 AM
Page 68
Problems and Solutions (VCR)
GB
Before contacting the Samsung after-sales service, perform the following simple checks.
Problem
No power
You cannot insert a video cassette
The television programme was not recorded
Timer recording was unsuccessful
No playback picture or the picture
is distorted
You cannot see normal broadcasts
Noise bars or streaks on playback
When the
II
button is pressed
during playback, the still picture
has severe "noise bars" streaks
Video Head Cleaning
If when tuning in your TV to the DVD-VCR
TV does not find the Screen
or the pattern when found suffers
from interference, it may be due to the
DVD-VCR output channel clashing with
the normal TV transmissions in your area.
To prevent this you will need to change the
DVD-VCR output channel in the following
way
If you are unable to solve the problem after reading the above instructions, note:
The model and serial number on the rear of your DVD-VCR
The warranty information
A clear description of the problem
Then contact your nearest SAMSUNG after-sales service.
68
Explanation/Solution
Check that the power plug is connected to a wall outlet.
Have you pressed the STANDBY/ON button?
A video cassette can only be inserted with the window
side up and the safety tab facing you.
Check the DVD-VCR aerial connections.
Is the DVD-VCR tuner properly set?
Check if the safety tab is intact on the cassette.
Was the STANDBY/ON button pressed to activate the timer?
Re-check the recording start/stop time settings.
If there was a power failure or interruption during timer
recording, the recording will have been cancelled.
Check to see if you are using a prerecorded tape.
Check the TUNER/EXTERNAL setting. It should be on
TUNER.
Check the TV/VCR aerial connections.
Press the TRK (+or -) buttons to minimize this effect.
A still picture may have "noise bars", depending on the
condition of the tape. Press the TRK (+or -) buttonsduring
SLOW motion to minimize this effect.
If poor pictures appear on a variety of cassettes, the video
heads may need cleaning. This is not a common problem
and unless it appears, the heads should not be cleaned.
When cleaning the video heads, read all instructions
provided with the head cleaning cassette. Incorrect head
cleaning can permanently damage the video heads.
1. Remove the aerial input plug from the socket marked (aerial
symbol) on the rear of the DVD-VCR.
2. Carry out the instructions "Tuning Your Television for the DVD-
VCR" (see page 14).
3. Carry out the instructions "Setting the DVD-VCR output
Channel" (see page 24), move the channel number
several channels down from the original setting.
(example:from 14 to 57).
4. Replace the aerial plug into the socket marked (aerial symbol)
on the rear of the DVD-VCR.
5. Re-tune your TV to the DVD-VCR again by following
instructions "Tuning Your Television for the DVD-VCR"
(page 14).
6. If the problem still exists repeat steps 1 to 5 moving several
more channels away from the original setting.
Troubleshooting Guide (DVD)
Before requesting service (troubleshooting)
Problem
Ensure that the disc is installed with the label side facing up.
Disc does not play.
Check the region number of the DVD.
This player cannot play CD-ROMs, DVD-ROMs, etc. Insert a DVD, a
VIDEO-CD or a CD.
5.1 channel sound is reproduced only when the following conditions
are met. :
5.1 channel sound is not
1)The DVD-VCR player is connected with the proper amplifier
being reproduced.
2) The disc is recorded with 5.1 channel sound.
Check whether the disc being played has the "Dolby 5.1 ch" mark on
the outside.
Check if your audio system is connected and working properly.
The features or action cannot be completed at this time because:
1. The DVD's software restricts it.
The
icon appears on
2. The DVD's software doesn't support the feature (e.g., angles).
screen.
3. The feature is not available at the moment.
4. You've requested a title or chapter number or search time that is
out of range.
Playback mode differs from
Some of the functions selected in the Setup Menu may not work
the Setup Menu selection.
properly if the disc is not encoded with the corresponding function.
The screen ratio cannot be
The Screen Ratio is fixed on your DVDs.
changed.
Make sure you have selected the correct Digital Output in the Audio
No audio.
Options Menu.
Press power on from a cold start with no disc in the unit. Press the
and
buttons simultaneously on the front panel for five
seconds.
Turn off the power, and then back on.
Press the SETUP button.
Forgot password
Use the ,
or , buttons to select DVD option. Press the ENTER
button. Use the
or
buttons to select parental mode.
Press the ENTER button.
The Parental Mode is now unlocked as indicated on the display.
Press the
or
button to select Parental. The Create Password
display will appear. You can now set your rating level and change
your password to a new number.
If you experience other
Go to the contents and find the section of the instruction book that
contains the explanations regarding the current problem, and follow
problems.
the procedure once again.
If the problem still cannot be solved, please contact your nearest
authorized service center.
Action
Page
P6
P48
P51-61
P44-49
P49
P48
P47
69
GB
Advertisement
Table of Contents
