1. Manuals
  2. Brands
  3. Sampo Manuals
  4. Monitor
  5. PME-42V3
  6. User manual

Sampo PME-42V3 User Manual

Sampo pme-42v3: user manual
Hide thumbs
Table of Contents

Advertisement

Quick Links

PLASMA DISPLAY

USER MANUAL

MODEL: PME-42V3

Advertisement

Table of Contents
loading

Related Manuals for Sampo PME-42V3

Summary of Contents for Sampo PME-42V3

  • Page 1: Plasma Display

    PLASMA DISPLAY USER MANUAL MODEL: PME-42V3...

  • Page 2: Table Of Contents

    TABLE OF CONTENTS FCC CLASS B STATEMENT… … … … … … … … … … … … … … … … … … … … … … … … … … … Wichtige Sicherheitshinweise… … … … … … … … … … … … … … … … … … … … … … … … … .… . IMPORTANT SAFETY INSTRUCTIONS…...

  • Page 3: Fcc Class B Statement

    •Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. •Consult the dealer or an experienced radio/TV technician for help. Shielded interconnected cables and shield power cords must be employed with this equipment t o insure compliance with the pertinent RF emission limits governing this device.

  • Page 4: Wichtige Sicherheitshinweise

    Wichtige Sicherheitshinweise 1. Bitte lesen Sie sich diese Hinweise sorgfältig durch. 2. Heben Sie diese Anleitung für den späteren Gebrauch auf. 3. Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen. Verwenden Sie keine Flüssig- oder Aerosolreiniger. Am besten dient ein angefeuchtetes Tuch zur Reinigung. 4.

  • Page 5: Important Safety Instructions

    4. When the monitor is not in use, disconnect it from the electric outlet. 5. If the picture displayed is in any way abnormal, turn off the unit and disconnect it from the electric outlet. Verify your signal wire connections and reconnect the TV to the electric outlet. 6. Read all instructions.
  • Page 6 IMPORTANT SAFETY INSTRUCTIONS 12. The unit should be operated from the type of power source indicated on the label. If the type of available power is unknown, consult your dealer or local power company. 13. The unit is equipped with a 3-pin grounded plug. The plug will only fit into a grounded power outlet. This is a safety feature.

  • Page 7: Back Panel Connections

    BACK PANEL CONNECTIONS BUTTON-REAR PANEL ¬ POWER IN MAIN POWER AUDIO IN AC 90~260V 50/60Hz Connecting to Audio equipment MAIN POWER: The AC main power switch. POWER IN: This terminal is for AC power cord. S-VIDEO: This terminal is for S-VIDEO signal cable, used with S-VIDEO equipment. COMPOSITE IN: These terminals are for composite video signals, used with video equipment with composite video outputs.

  • Page 8: Back Panel Connections

    BACK PANEL CONNECTIONS USB: This terminal is for control system signal, for use with IBM PCs and compatibles. COMPONENT VIDEO IN: This terminal is a multi-functional terminal which can receive high-definition YPBPR: Use this terminal to connect high-definition, progressive scan component video signals from progressive scan video equipment such as progressive scan DVD players and high end HDTV decoders.

  • Page 9: Remote Control Functions

    REMOTE CONTROL FUNCTIONS...

  • Page 10: Remote Control Functions

    REMOTE CONTROL FUNCTIONS The plasma display panel features advanced on-screen adjustments for optimal viewing. You can access these features by using the controls located on the plasma display panel. Pressing the POWER button turns on the unit. When power is on, the green POWER POWER LED illuminates.
  • Page 11 REMOTE CONTROL FUNCTIONS 8. ON Press these buttons to directly turn the power on or power off. POWER 9. －MENU＋ To display the monitor’ s on-screen display, press MENU +/- button. Use the ADJ +/- button for setting plasma display panel settings. －ADJ＋...

  • Page 12: Battery In Remote Control

    BATTERY IN REMOTE CONTROL Open the cover on the back of the remote and insert two R03/AAA/SUM-4 batteries. Be sure the polarity is correct. Replace the cover NOTES: To avoid damage from possible battery leakage, remove the batteries for extended unused periods. Be sure that there are no obstructions between the Remote Control and the Monitor.

  • Page 13: Front Panel And Connections

    FRONT PANEL AND CONNECTIONS Front View POWER Pressing the POWER button turns on the unit. When power is on, the green POWER LED illuminates. When power is off, the unit switches to standby mode illuminating the red STANDBY LED. To display the monitor’ s on-screen display, press MENU +/- button. －MENU＋...

  • Page 14: On Screen Display Menu Settings

    ON SCREEN DISPLAY MENU SETTINGS The plasma display panel features advanced on-screen adjustments for optimal viewing. You can access these features by using the MENU +/- buttons located on the plasma display panel (accessible by pressing the center of the door) or by using the remote control. When the MENU +/- buttons are pressed, various On-Screen Display menus are displayed depending on the input source selected.
  • Page 15 ON SCREEN DISPLAY MENU SETTINGS BRIGHTNESS: Select icon to adjust the overall picture brightness (image black level). Set the brightness so that the dark areas of the monitor remain black. Press the ADJ - button to decrease brightness. Press the ADJ + button to increase brightness. This setting is available to all video signal inputs CONTRAST: Select icon to adjust the contrast (image white level).

  • Page 16: On Screen Display Menu Settings

    ON SCREEN DISPLAY MENU SETTINGS COLOR: Select icon to adjust the color of the displayed image. Press the ADJ – button to decrease color. Press the ADJ + button to increase color. TINT: Select icon to adjust the tint of the displayed image. Press the ADJ + button to increase the level of green in the image.

  • Page 17: Power Management Function

    The power management function requires TTL horizontal and vertical sync. Power saving is invalid if display is in AV, YCBCR, YPBPR mode. ® As an ENERGY STAR partner, Sampo Corporation has determined that this product meets the ENERGY ® STAR guidelines for energy efficiency.

  • Page 18: Trouble Shooting

    TROUBLE SHOOTING The following list represents possible anomalies you may encounter and the methods for remedying them Please refer to this checklist prior to contacting a service representative. Trouble condition No picture 1.Power cord disconnected? 2.Power switch on? 3.Signal cable properly connected? 4.

  • Page 19: Specifications (Preliminary)

    SPECIFICATIONS (Preliminary) Display panel a. Screen size b. Aspect ratio c. Number of pixels d. Pixel pitch e. Luminance Power a. Input voltage b. Input current c. Inrush current d. Power consumption e. Stand-by & DPMS Connector type AV/S-VIDEO signal a.
  • Page 20 SPECIFICATIONS (Preliminary) DVI signal a. Type b. Polarity c. Frequency Audio signal a. input level b. practical max Horizontal size (Standard) Vertical size (Standard) Dimensions Width Height Depth Package dimensions Width Height Depth Weight Net weight User controls Operating Temperature Temperature Pin assignments for D-SUB connector (in / loop out) Pin 1 : RED...

  • Page 21: Specifications (Preliminary)

    SPECIFICATIONS (Preliminary) Pin assignments for 24 pin DVI connector Pin 1 : TMDS Data 2- Pin 2 : TMDS Data 2+ Pin 3 : TMDS Data 2/4 Shield Pin 13 : TMDS Data 3+ Pin 4 : TMDS Data 4- Pin 5 : TMDS Data 4+ Pin 6 : DDC Clock Pin 7 : DDC Data...

  • Page 22: Installation Method For Wall Mounting

    INSTALLATION METHOD FOR WALL MOUNTING Set-up steps 1. Set up the roll bars marked 1,2,3,4. 2. Put the two roll bar terminals into the wall-mounting angle. Then fix them in place with M4 size screws. They are marked 5,6,7,8. 3. Use the 3/8” driver head to fix the wall-mounting angle. The wall-mounting angle must be fixed to cement Wall.

  • Page 23: Installation Method For Wall Mounting

    INSTALLATION METHOD FOR WALL MOUNTING -21-...

Table of Contents