Download Print this page
SLX Extreme Series Fitting Instructions Manual

SLX Extreme Series Fitting Instructions Manual

For holden colorado 2012
Hide thumbs Also See for Extreme Series:

Advertisement

Quick Links

SHORELINE 4X4 INSTRUCTIONS
1. Auto electrical work should be carried out by a competent person. Vehicle
wire colours are listed as a guide only and may vary on some makes and
models.
2. The function of each wire should be checked before any connections are
made.
3. All wires tapped into should be soldered and then insulated with electrical
tape or heat shrink.
4. Grounding/Earth points must always be connected to the factory grounding
points, not to the battery negative terminal. See owner's manual.
5. Using only a LED test light, test all electrical components of the vehicle before
and after wiring.
This is to ensure everything works correctly.
6. the installation of large or light-coloured antennas or aerials to the
front of a bull bar as this may cause the lane departure system to malfunction.
Only a competent person should perform accessory installations. It is the
responsibility of this person to ensure correct fitment.
Whilst working on this vehicle, always use appropriate safety equipment.
Read and understand instructions fully before commencing fitment.
Check the hardware supplied against the contents list on the following pages.
Do not use this product for any vehicle make or model other than specified in
these instructions.
This product and or hardware must not be modified in any way. Do not
remove labels from this product.
Recording the batch number on the customer's job card is good practice for
future reference, or complete the information below and file with customer job
card.
Care
To maintain the finish of the product, wash regularly using a PH neutral car
wash, hose off and
chamois dry.
Do not use acidic or alkaline cleaners.
Plastic components can be maintained with a silicone spray or similar (non-
acidic or alkaline based).
Ironman 4x4 recovery points are FEA tested during design and destruction
tested during development
to establish the Working Load Limits (WLL).
EXTREME SERIES BULLBAR

Advertisement

loading
Need help?

Need help?

Do you have a question about the Extreme Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for SLX Extreme Series

  • Page 1 SHORELINE 4X4 INSTRUCTIONS EXTREME SERIES BULLBAR 1. Auto electrical work should be carried out by a competent person. Vehicle wire colours are listed as a guide only and may vary on some makes and models. 2. The function of each wire should be checked before any connections are made.
  • Page 2 • recovery points have been designed as a matching pair, supplied as right and left sides for vehicle-specific fitment. • Do not use this recovery point for any other vehicle make or model other than the one intended. • Do not alter or modify the recovery point in any way. Doing so may compromise the strength and integrity of the recovery point.
  • Page 3 Shoreline 4 x es Bullbar reme Se...
  • Page 4 Fitting instructions for Holden Colorado 2012 on Front TOW points only - Rated to 3.75T - NOT FOR SNATCHING www.slx4x4.com.au (08) 9444 2946 126 Hector St W - OSBORNE .A. 6017...
  • Page 5 1. Congratulations on purchasing your very own Shoreline 4x4 Extreme Series Bulbar. o start, clear an ar ea a round the front of your car and unwrap the ba 2. If you previous had a Xrox bulbar your front end will already be half cut.
  • Page 6 3. It is suggested you remove the front grille off the car inorder to make the final cut shown below. You will need to remove the 2 barbs either side under the head lights with bolt cutters or grinder, do not grind near colour coded bullbar 4.Now separate the bar from the bracket.
  • Page 7 7.Trim and secure the inner wheel line where applicable Carefully mount the Extreme Series bar it is best to get someone to help you. The bulbar alignment can be difficult. Its best to have bolts loose enough so two persons can hold the bar in place while a 3 tightens the bar.
  • Page 8 NOTE : When you remove RG bumper the alignment of the actual gaurd may change profile due to potrivot supports being removed, if you find lower section or side profile does not line up enough see solution end of this document Alignment can be difficult on the Colorado RG, Suggest approx.
  • Page 9 ALIGNMENT SOLUTION FOR COLORADOS. SIMPLY SPACE GAURD OUT WITH REQUIRED NUMBER OF WASHERS...
  • Page 10 You may wish to purchase 12x12mm Adhesive form available from clark rubber for $7, you need about 60cm worth, 30cm on each side and you apply It between guard and bulbar for seamless look...

This manual is also suitable for:

Shoreline 4x4 bullbar x-1