Argus Security TAURUS TW-DT-01/BL Quick Start Manual

TW-DT-01
Wireless heat detector
Available also in black plastic: TW-DT-01/BL
IMPORTANT TO CONSIDER
IMPORTANT TO CONSIDER
When mounting a wireless device a comprehensive radio survey
When mounting a wireless device a comprehensive radio survey
should have been carried out to establish the location that provides
should have been carried out to establish the location that provides
the best coverage and optimum reach. Taking into consideration the building
the best coverage and optimum reach. Taking into consideration the building
structure and materials, the survey identifies the wireless infrastructure
structure and materials, the survey identifies the wireless infrastructure
required and product locations for optimum performance, identifying
required and product locations for optimum performance, identifying
any factor that could prevent radio integrity.
any factor that could prevent radio integrity.
Avoid fixing or mounting the unit close to the following:
Avoid fixing or mounting the unit close to the following:
• Equipment that utilises large electrical currents
• Equipment that utilises large electrical currents
• Large metal objects or structures
• Large metal objects or structures
• Fluorescent lighting fittings
• Fluorescent lighting fittings
• Metal ceiling structures
• Metal ceiling structures
• IT cabling.
• IT cabling.
Keep 2 meters minimum spacing between other wireless equipment
Keep 2 meters minimum spacing between other wireless equipment
in the area to avoid signal interference.
in the area to avoid signal interference.
EN54 approved environmental temperature range is -10°C to +55°C
EN54 approved environmental temperature range is -10°C to +55°C
UNBOXING
UNBOXING
• When unboxing the detector you will find the unit and its mounting base.
• When unboxing the detector you will find the unit and its mounting base.
• This comes with pre-formed mounting holes to mount the detector base and a securing screw
• This comes with pre-formed mounting holes to mount the detector base and a securing screw
on the base to ensure there is no unwanted removal.
on the base to ensure there is no unwanted removal.
For more information, please refer to the complete product manual.
For more information, please refer to the complete product manual.
ARGUS SECURITY SRL, VIA DEL CANNETO, 14, 34015 MUGGIA, (TS), ITALY
ARGUS SECURITY SRL, VIA DEL CANNETO, 14, 34015 MUGGIA, (TS), ITALY
T: +39-040.23.96.411, E: info@argussecurity.it, W: www.argussecurity.it
T: +39-040.23.96.411, E: info@argussecurity.it, W: www.argussecurity.it
WIRELESS HEAT DETECTOR
WIRELESS HEAT DETECTOR
QUICK START GUIDE
QUICK START GUIDE
THE BOX INSIDE THE BOX
THE BOX INSIDE THE BOX
THE BOX
QR code • 1 x Heat Detector
QR code • 1 x Heat Detector
Taurus QR code
Part number with mounting base
Part number Manual QR code with mounting base
Product name • 2 x CR123A batteries
Product name Product code • 2 x CR123A batteries
• 1 x Product manual
• 1 x Product manual
Product name • 1 x Quick start guide
• 1 x Quick start guide
• 1 x QR code
• 1 x QR code
TW-DT-01
TW-DT-01
MOUNTING STEPS
MOUNTING STEPS
Proceed as follows to complete the device installation.
Proceed as follows to complete the device installation.
• Remove the detector's dust cover, intended to protect
the unit during shipping.
• Remove the detector's dust cover, intended to protect
• Remove the detector from the base twisting
the unit during shipping.
anticlockwise.
• Remove the detector from the base twisting
anticlockwise.
REMOVABLE
TAG
REMOVABLE
TAG
• A plastic pop out tag is removable from the base
to enable you to label the address of the detector,
• A plastic pop out tag is removable from the base
prior to fixing to the ceiling: pop out the device label tag
to enable you to label the address of the detector,
from the base and insert it into the side.
prior to fixing to the ceiling: pop out the device label tag
• Screw the base to the ceiling using all fixing holes
from the base and insert it into the side.
and appropriate-sized screws.
• Screw the base to the ceiling using all fixing holes
and appropriate-sized screws.
Ensure the programming switch in the base of the detector
is in position ON.
Ensure the programming switch in the base of the detector
is in position ON.
1
1
UNLOCK
UNLOCK
• Locate the mounting holes and mark them using a pencil
on the desired surface you are drilling.
• Locate the mounting holes and mark them using a pencil
• Using a suitable-sized drill bit (6 mm) drill the marked
on the desired surface you are drilling.
screw points on your chosen surface.
• Using a suitable-sized drill bit (6 mm) drill the marked
• Ensure you use the correct fixings for the type of surface
screw points on your chosen surface.
you are mounting to.
• Ensure you use the correct fixings for the type of surface
you are mounting to.
3
3
Remove the battery compartment cover on the base
on the detector.
Remove the battery compartment cover on the base
on the detector.
5
5
SWITCH
ON
SWITCH
ON
Remove the batteries' insulating tab ensuring
the batteries are kept in their lodgement.
Remove the batteries' insulating tab ensuring
the batteries are kept in their lodgement.
L50-DT-0001 (Rev_P.3)
2
2
MOUNTING
HOLES
MOUNTING
HOLES
4
4
6
6
REMOVE
INSULATING
REMOVE
TAG
INSULATING
TAG
L50-DT-0001 (Rev_P.1)
L50-DT-0001 (Rev_P.1)