Related Manuals for NoiseKen SG-7040A
Summary of Contents for NoiseKen SG-7040A
- Page 1 INSTRUCTION MANUAL MULTI CHANNEL SIGNAL GENERATOR MODEL SG-7040A NOISE LABORATORY CO., LTD. Edition 1.00 AEJ00616-00E-0A...
- Page 2 NOTICE • The contents of this instruction manual（the “Manual”） are subject to change without prior notice. • No part of the Manual may be reproduced or transferred, in any form and for any purpose, without the permission of Noise Laboratory Co., Ltd.(the “Company”) •...
-
Page 3: Important Safety Precautions
1. IMPORTANT SAFETY PRECAUTIONS As each of the following items is very important matter to be attended, thoroughly read it before operation of the SG-7040 (hereinafter “the Unit”). 1. The Unit cannot be used in a fire prohibited area or other explosive areas. If used in such an area, the Unit is liable to cause combustion or ignition due to electric discharge etc. - Page 4 Memorandum...
-
Page 5: Application Form For Instruction Manual
2. APPLICATION FORM FOR INSTRUCTION MANUAL We place an order for an instruction manual. Model: SG-7040A Serial No.: Applicant: Company name: Address: Department: Person in charge: Tel No.: Fax No. Cut off this page “APPLICATION FORM FOR INSTRUCTION MANUAL” from this volume and keep it for future use with care. - Page 6 Memorandum...
-
Page 7: Table Of Contents
3. CONTENTS I M P O R T A N T S A F E T Y P R E C A U T I O N S ..................1 A P P L I C A T I O N F O R M F O R I N S T R U C T I O N M A N U A L . -
Page 8: Preface
4. PREFACE We thank you for your purchase of the MULTI CHANNEL SIGNAL GENERATOR SG-7040A (hereinafter “the Unit”). This instruction manual (“the Manual”) contains how to use the Unit and other important information. In order to obtain the highest performance from the Unit, thoroughly understand the contents of the Manual and use as ready reference for operation. -
Page 9: Basic Safety Precautions
5. BASIC SAFETY PRECAUTIONS 5-1. Symbols of Hazard It expresses a DANGER. DANGER 危険 DANGER indicates an impending dangerous injury or condition resulting in a serious death , if such a condition is not avoided. It expresses a WARNING. WARNING indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. -
Page 10: R E C A U T I O N S
BASIC SAFETY PRECAUTIONS Supply power for test within the rated range (Do not let output terminals be short-circuited). Do not misplace the polarity. Otherwise the Unit may be damaged. P recautions for operation and connection 【 【 【 【 】 】 】 】 Avoid using or storing the Unit in high or low temperature environment (Operating temperature range: 15~35°C / Operating humidity range: 25~75%). -
Page 11: Accessory
6. Accessory A) AC cable ······································································ 1 B) Coaxial cable (BNC-BNC 2m) ·········································· ( ※ C) Output cable (1m) ·························································· ( ※ D) Solderless terminal (M4) ················································· Channel × Solderless terminal (M6) ················································· Channel × Solderless terminal (M8) ················································· Channel ×... -
Page 12: N A M E A N D F A N C T I O N O F E A C H P A R
7. NAME AND FANCTION OF EACH PART 7-1. Front Panel (The installed waveform generating unit varies according to the model number.) ⑤ ④ ⑥ ③ ⑦ ② ⑧ ① Power button and lamp P OWER ① 【 】 Turns on the waveform generating part. The pilot lamp is alight while electrified. In starting the system, turn on the Unit prior to a bipolar power supply. - Page 13 7.NAME AND FANCTION OF EACH PART 7-2. Rear Panel ⑪ ⑩ ⑨ ⑨ AC inlet 【 A C INPUT 】 Connect power supply with AC cable. Connect PE to the protective earth.Fuse(3.15A). USB connector U SB ⑩ 【 】 Used for connecting PC with the USB cable of accessory to control waveform generator remotely (USB1.1).
-
Page 14: S E T T I N G A N D C O N N E C T I O
8. SETTING AND CONNECTION 8-1. Setting and Preparation 1) Set up the Unit and the bipolar power supply on a stable space. 2) Install the application software to PC. 8-2. Connection Oscilloscope オ シ ロ ス コ ー プ E X T . T R I G T o : P C U S B Bipolar power supply... -
Page 15: O P E R A T I O
9. OPERATION 9-1. Initial Setting 1) If the bipolar power supply is AS-161-xx, make the BIAS setting key “0”, and set the input gain switching key “x10”. 2) In case other bipolar power supplies are used, set them according to the instruction manual of them. 9-2. - Page 16 10. SYSTEM CONFIGURATION Signal generator 信号発生器 信号発生器 信号発生器 信号発生器 U S B U S B C H 1 C H 2 C H 3 C H 4 Prepared by User ユ ー ザ ー に て ご 用 意 C H 1 P o w e r A m p ( 別...
-
Page 17: S P E C I F I C A T I O N
11. SPECIFICATIONS B ase Unit 【 】 Channel Max. 4 channels Emergency button Make the generator part stop completely Interlock Emergency stop status when the external point of contact is cut off (Usually short-circuited). Trigger output for oscilloscope One point / BNC connector / 0-5V Active low (OSC-SYNC) Set a trigger point at an arbitrary point in waveform generating software. - Page 18 S P E C I F I C A T I O N S P C software control part 【 】 Drawing waveforms Arbitrary waveform DC output time range 1µs 3 0min ～ Rectangular wave cycle rang 10µs ～ 3 0min Sawtooth wave cycle range 10µs ～...
- Page 19 S P E C I F I C A T I O N S Waveform Structure limit Combined Waveform File Sequence File Waveforms Sequence File ○ ○ ○ Rectangular wave ○ ○ ○ Sawtooth wave ○ ○ ○ Ramped sine wave ○...
-
Page 20: W A R A N T
12. WARANTY Servicing terms The following terms are applicable to servicing by Noise Laboratory Co., Ltd., (hereafter referred to as the Company) provided to maintain the intended performance of its products. 1. Scope The following terms shall apply only to products made by the Company. 2. - Page 21 12.WARANTY Limited warranty Noise Laboratory Co., Ltd. (hereafter referred to as the Company) warrants its products to be free from defects in materials and workmanship under normal use and service for a period of one year from date of delivery. In the event of failure of a product covered by this warranty, the Company will repair the product or may, at its option, replace it in lieu of repair without charge.
-
Page 22: M A I N T E N A N C
13. MAINTENANCE When repair, maintenance or internal adjustment of the unit is required, a qualified service engineer takes charge of such work. Maintenance on the user side is restricted to the outside cleaning and functional check of the unit. When checking or replacing the fuse, turn off the switch of the unit and disconnect the plug socket beforehand. -
Page 23: N O I S E L A B O R A T O R Y S U P P O R T N E T W O R
14. NOISE LABORATORY SUPPORT NETWORK If a symptom which seems a trouble is found, inform the model name and serial number of the product together with the symptom to Noise Laboratory or your nearest sales agent of Noise Laboratory. When the product is returned to Noise Laboratory, write the state of the trouble, contents of your request, model name and serial number in a repair order, and pack the product and repair order sheet in the former package of equivalent suitable for transit and send them back. - Page 24 NOISE LABORATORY CO., LTD. Produced by: Noise Laboratory Co., Ltd. 1-4-4, Chiyoda, Chuo-ku, Sagamihara City, Kanagawa Pref., 252-0237, Japan TEL: +81-(0)42-712-2051 FAX: +81-(0)42-712-2050 URL: http://www.noiseken.com Printed in Japan...
Need help?
Do you have a question about the SG-7040A and is the answer not in the manual?
Questions and answers