Advertisement
Quick Links
EROAD Clarity Dashcam
Install Guide
EROAD Technical Support
Parts & Equipment
Dashcam Parts
Placement
3-wire Install Using the HR003101A Loom
Dashcam Connected Only
Photo Verification
Specifications
Safety & Best Practice
Legal
EROAD Technical Support
North America
Australia
New Zealand
1-855-503-7623 support@eroad.com
1800 437 623
0800 437 623
support@eroad.com.au
support@eroad.co.nz
Advertisement
Related Manuals for EROAD HR003101A
Summary of Contents for EROAD HR003101A
- Page 1 EROAD Clarity Dashcam Install Guide EROAD Technical Support Parts & Equipment Dashcam Parts Placement 3-wire Install Using the HR003101A Loom Dashcam Connected Only Photo Verification Specifications Safety & Best Practice Legal EROAD Technical Support North America 1-855-503-7623 support@eroad.com Australia 1800 437 623 support@eroad.com.au...
- Page 2 ▪ EROAD Windshield sticker ▪ I/O Port guard Clarity Connected Kit ▪ Everything in STD, + Windshield Kit, AND: ▪ HR003101A 3-wire loom (No GPIOs), or ▪ HR003100A loom, GPIO-ready, or ▪ HR003105A loom, GPIO-ready, and/or ▪ ECM Y-cable GPIO Remote Record Button kit (HR003107A) ▪...
- Page 3 Remove the power cable (if the unit is already mounted). Insert the SD card into the ‘SD’ port. The gold contacts face the EROAD side of the unit. Push it in until the card sticks in place, flush with the port surface.
- Page 4 Clarity Dashcam Parts Windshield mounting plate Road camera Road lens cap Cable Insert + cable I/O Port guard Cab camera Cab lens cap Camera locking bolts Manual record The Clarity cameras each have a RESTRICTED RANGE OF ROTATION. Do NOT attempt to rotate them with the locking bolts tightened, or past their tolerance limits (approximately 90°...
-
Page 5: Mounting The Dashcam
Placement Position the dashcam inside, in the approximate middle-top of the windshield, or if this location is already occupied, slightly passenger-side. The front camera should be approximately 8 inches (20 cm) below the windshield wipers' highest sweep-point. The unit should be mounted outside the driver’s normal sight lines of the road ahead, highway signs, signals and all mirrors. - Page 6 occasionally from outside the vehicle). Push firmly for 20s. Wait another 2 minutes for full adhesion. Attach the dashcam body into the mounting plate. Leave the protective film on the lenses until the Install Wizard phase. Fig. 1 Fig.1: CORRECT Full contact with the mounting plate to the windshield.
- Page 7 ▪ Down the windshield's A-pillar (out of sight, secured, tucked into the lining trim), down the back of the dashboard. ▪ In the shortest, most convenient path to your key connection points. Find the vehicle’s junction and/or fuse box under the dash. It’s good practice to take a picture of the vehicle’s current configuration to use as a reference later.
- Page 8 3-wire Install Using the HR003101A Loom The following diagram shows a basic connection for the Clarity Connected and Clarity Solo dashcams using the HR003101A 3- wire loom along with a basic Ehubo wiring diagram. If you are installing a Clarity Connected camera, your Ehubo is likely to be fused and connected already.
- Page 9 3-Wire Install using the HR003191A loom (Diagram) 3101: 3-WIRE, NO GPIOS...
- Page 10 Dashcam Connected Only Consult the dedicated Ehubo Installation Guide for full instructions. But as a wiring check: Connect the BLACK wire on the 10-way wiring loom to an appropriate grounding location. Connect the RED wire on the 10-way wiring loom to a permanent power source.
- Page 11 Remote record button install (HR003106)- Optional The 12-2 wire loom that comes with this remote button kit IS NOT USED for this install. Note 4 Drill a 14 mm (0.55 in) diameter hole into a dashboard panel (or similar site within comfortable reach of the driver).
- Page 12 HR003101A 12-way Pin-out GPIO input 1 Orange Not Connected +ve power in Not Connected Not Connected Not Connected Ignition Yellow/Red Not Connected Not Connected Ground Black +ve power out Purple Not Connected 2-way Connector Pin-out +ve power out Purple GPIO1, input 1...
- Page 13 3-wire Install Using the HR003100A Loom (GPIO) The following diagram shows a basic connection for the Clarity Connected and Clarity Solo dashcams using the HR003100A 12-wire loom along with a basic Ehubo wiring diagram. If you are installing a Clarity Connected camera, your Ehubo is likely to be fused and connected already.
- Page 14 3-wire Install Using the HR003100A Loom (GPIO, Diagram) 3100: 3-WIRE, GPIOS...
-
Page 16: Specifications
9-32 V DC Temperature -20 to +60°C IP Rating IP41 Safety & Best Practice EROAD expects installers and contractors to understand and follow all relevant health and safety regulatory requirements. Before installing EROAD equipment in a vehicle you must be, in... - Page 17 Australia, an approved EROAD installer and, in New Zealand, an accredited EROAD installer. The installer must wear appropriate Personal Protective Equipment (PPE) for the install risk and customer requirements. PPE may include safety glasses, safety shoes, work gloves, hard hat, high visibility vest, sun cream, sun hat and coveralls. You must understand and comply with the safety requirements of customers or third parties.
- Page 18 Use of the EROAD CoreHub Xtreme is subject to the terms and conditions outlined on EROAD’s website. EROAD disclaims all liability for any installation of EROAD equipment in a way that may cause accidents, damage, or violate the law.
Need help?
Do you have a question about the HR003101A and is the answer not in the manual?
Questions and answers