Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Nelsen Corporation C Series
Summary of Contents for Nelsen Corporation C Series
- Page 1 C-SERIES WS Series Models 1" & 1-1/4" Control Valve WS Programming Guide...
-
Page 2: Table Of Contents
Table of Contents Control Valve Function & Cycles of Operation 3 - 4 ................................System Set-Up 5 - 6 ..................................................Setting Options Table ..............................................Softener System Setup 8 - 9 ............................................... Filter System Setup 9 - 10 ................................................Installer Displays/Settings ............................................ -
Page 3: Control Valve Function & Cycles Of Operation
Control Valve Function & Cycles of Operation This glass filled Noryl (or equivalent) fully automatic control valve remembers all settings for up to 8 hours if control valve is designed as the primary control center the power goes out and the battery is not depleted. After to direct and regulate all cycles of a water softener or 8 hours, the only item that needs to be reset is the time of filter. - Page 4 Control Valve Function & Cycles of Operation Table 2 - Backwash Normal Length Softener Table 4 shows the order of the cycles when the valve is set up as a filter. When the control valve is used as a Cycle Times in Minutes downflow regenerating filter, the OEM has the option to WS1 &...
-
Page 5: System Setup
System Setup Table 5 Table 6 WS1 & WS1.25 Regenerating Filter WS1 & WS1.25 Non-Regenerating Filter Single Backwash Double Backwash Single Backwash Double Backwash Normal Longer Normal Longer Normal Longer Normal Longer Backwash Backwash Regenerate Rinse 2nd Backwash 2nd Backwash Rinse 2nd Rinse Total... - Page 6 System Setup Table 7 DIR/Time Clock Options Filter Settings Time Clock Reserve Capacity Softener Regenerant BW Only Day Override Gal Capacity Automatically Calculated If desired enter a value less Any Number than estimated capacity Automatically Calculated Any Number Auto If desired enter a value less Any Number Any Number than estimated capacity None...
-
Page 7: Setting Options Table
WS Controller - Setting Options Table Filters should only use shaded options Volume Regeneration Result Capacity Time Option Override AUTO NORMAL Reserve capacity automatically estimated. Regeneration occurs when volume capacity falls below the reserve capacity at the next Regen Set Time. AUTO NORMAL Any Number Reserve capacity automatically estimated. -
Page 8: Softener System Setup
WS Controller - Softener System Setup STEP 1S STEP 5S Press NEXT and Backwash: Select q simultaneously “NORMAL” or for 3 seconds. If “LONGER” using screen in Step 2S does not appear in 5 seconds the lock q or p. See on the valve is activated. -
Page 9: Filter System Setup
WS Controller - Softener System Setup STEP 8S STEP 9S Set regenerant Set Regeneration downflow or Time Option using upflow using q or p: q or p: • “NORMAL” • “dn” if the means regenerant is to regeneration RETURN TO NORMAL MODE fl ow downward through the media;... - Page 10 WS Controller - Filter System Setup STEP 4F STEP 6F Backwash: Select Set Refill option using q or p: using q or p: • “NORMAL” for • “PoST” to refill one “NORMAL” the brine tank backwash (14 after the final minutes);...
-
Page 11: Installer Displays/Settings
Installer Display Settings STEP 1i STEP 4i Press NEXT and p Next simultaneously for Regeneration 3 seconds. Time (hour): Set the hour of day for STEP 2i regeneration using porq buttons. Hardness: Set AM/PM toggles the amount of after 12. The default time is 2:00 a.m. This display will hardness in grains show “REGEN on 0 GAL”... -
Page 12: User Displays/Settings
User Display Settings General Operation When the system is operating one of two displays will be shown. Pressing NEXT will alternate between the displays. One of the displays is always the current time of day. The second display is one of the following: days remaining or gallons remaining. -
Page 13: Diagnostics
User Display Setting Diagnostics STEP 1D Set Time of Day The user can also set the time of day. Time of day should Press porq only need to be set after power outages lasting more than simultaneously for three 8 hours, if the battery has been depleted and a power seconds. - Page 14 Diagnostics STEP 4D - (Continued) STEP 7D p button will show day 1 (which would be yesterday) and Flow Rate, Maximum flashes the reserve capacity used. Pressing the p button Last Seven Days: The again will show day 2 (the day before yesterday) and the maximum flow rate reserve capacity.
-
Page 15: Valve History
Valve History STEP 1VH STEP 5VH Press pandq Days, Total Since simultaneously for Start-Up: This display three seconds and shows the total days release. Then press since startup. pandq simultaneously and release. If screen in step 2VH does not appear in 5 Press the NEXT button seconds the lock on the valve is activated. -
Page 16: Front Cover & Drive Assembly
CL3186UK AC Adapter 220-240V-12V UK CL3186-01 AC Adapter Cord Only CL3175-01 Fully Seated CL3108-10BOARD CL3109 CL3110 CL3002 CL3107-01 (Complete CL3106-01 Assembly) Part No: C-Series WS Program, Rev0816 © 2018 Nelsen Corporation...