Download Print this page

NORTH COAST ROCKETRY Vektra Instructions Manual

Flying model rocket

Advertisement

Quick Links

VEHICLE DATA SHEET
Physical Data
Parameter
Dimension
Length
37" (94 cm)
Diameter
2.64" (6.7 cm)
Weight
19.5 oz (555 g)
Predicted Altitudes
Motor
Estes E16-4
Estes F15-4
Aerotech F25-6W
Aerotech F50-6/9T
Aerotech G40-7W
Aerotech G80-10T
• A 36" nylon parachute is not included in this kit. The NCR
36" Ripstop Nylon High Visibility Parachute (Part #822) is
recommended for this kit.
• This kit is recommended for adults(18 and older) only. Launch systems, model rocket motors, launch supplies, tools, and
building materials are not included.
• Do not modify the design of the rocket! Changes to the design may affect the stability, and hence, the safety of the
rocket.
• North Coast Rocketry certifies that it has exercised reasonable care in the design and manufacture of its products.
However, as we cannot control the use of our products once sold, we cannot assume any responsibility or liability for
product usage.
• North Coast rocketry shall not be held responsible for personal injury or property damage resulting from the use of our
product. The buyer assumes all risks and liabilities arising from the use of our product and uses our product on these
conditions.
• North Coast Rocketry makes no warranty regarding our products, except for defects in materials or workmanship for a
period of one year after purchase.
• If any of these terms are unacceptable, please return the item to the point of purchase.
North Coast Rocketry
Predicted Altitude
407 ft (124 m)
686 ft (209 m)
1,164 ft (355 m)
1.245 ft (380 m)
1,812 ft (552 m)
2,386 ft (727 m)
Copyright © 2020 North Coast Rocketry®. All rights reserved
Vektra
Flying Model Rocket Instructions
Designed by Matt Steele
NCR 9208 (07/20)

Advertisement

loading

Summary of Contents for NORTH COAST ROCKETRY Vektra

  • Page 1 • North Coast rocketry shall not be held responsible for personal injury or property damage resulting from the use of our product. The buyer assumes all risks and liabilities arising from the use of our product and uses our product on these conditions.
  • Page 2: Parts List

    North Coast Rocketry Before You Start: Parts List Thank you for purchasing this North Coast Rocketry® model kit. We hope you have an enjoyable time constructing and flying this model rocket. Please read all of these instructions to become familiar with...
  • Page 3 Using epoxy, bond the ring in place. Repeat with the other ring in the mid location. Fillet both rings to the tube with epoxy. Copyright © 2020 North Coast Rocketry®. All rights reserved...
  • Page 4 CA. Trim the excess off. □ Tie one end of the elastic shock line onto the top cable loop and triple knot it. Trim the excess off. Copyright © 2020 North Coast Rocketry®. All rights reserved...
  • Page 5 Epoxy the other launch lug attach the Quick Link. See the next page for a photo. aft of the 2” mark. Fillet the lugs for added strength. Copyright © 2020 North Coast Rocketry®. All rights reserved...
  • Page 6 Remove the backing paper and position the decal on the model. Burnish the decal to stay in place. □ Spray the entire model with a clear coat to protect the finish. Copyright © 2020 North Coast Rocketry®. All rights reserved...
  • Page 7: Flight Preparations

    • The model slides freely on the launch rod or rail, with no ground. binding, sticking or misalignment of the launch lugs or buttons; Fly safely and have fun! • If any problems are detected, correct them before attempting to fly. Copyright © 2020 North Coast Rocketry®. All rights reserved...
  • Page 8 Minimum Site Dimensions (ft.) 0.00--1.25 1/4A, 1/2A 1.26--2.50 2.51--5.00 5.01--10.00 10.01--20.00 20.01--40.00 1,000 40.01--80.00 1,000 80.01--160.00 1,000 160.01--320.00 Two Gs 1,500 Join the National Association of Rocketry! Visit www.nar.org for details! Copyright © 2020 North Coast Rocketry®. All rights reserved...