Download Print this page

NORTH COAST ROCKETRY HyperSwift SR-99 Instructions Manual

Flying model rocket

Advertisement

Quick Links

VEHICLE DATA SHEET
Physical Data
Parameter  
Dimension  
Length  
37"   ( 94   c m)  
Diameter  
2.64"   ( 6.7   c m)  
Weight  
15.8oz   ( 450   g )  
Predicted Altitudes
Motor  
Estes   E 15-­‐4  
Estes   F 15-­‐4  
Aerotech   F 26-­‐6FJ  
Aerotech   F 50-­‐6T  
Aerotech   G 40-­‐10W  
Aerotech   G 80-­‐10T  
•  This kit is recommended for adults(18 and older) only. Launch systems, model rocket motors, launch supplies, tools, and building
materials are not included.
•  Do not modify the design of the rocket! Changes to the design may affect the stability, and hence, the safety of the rocket.
•  North Coast Rocketry certifies that it has exercised reasonable care in the design and manufacture of its products. However, as we
cannot control the use of our products once sold, we cannot assume any responsibility or liability for product usage.
•  North Coast rocketry shall not be held responsible for personal injury or property damage resulting from the use of our product. The
buyer assumes all risks and liabilities arising from the use of our product and uses our product on these conditions.
•  North Coast Rocketry makes no warranty regarding our products, except for defects in materials or workmanship for a period of one
year after purchase.
•  I f any of these terms are unacceptable, please return the item to the point of purchase.
North Coast Rocketry
SR-99 HyperSwift
Predicted   A l2tude  
514   B   ( 156   m )  
848   B   ( 258   m )  
1,215   B   ( 370   m )  
1,175   B   ( 357   m )  
1,682   B   ( 512   m )  
2,136   B   ( 651   m )  
Copyright © 2012, 2015 North Coast Rocketry®. All rights reserved  
Flying Model Rocket Instructions
Designed by Matt Steele
NCR 9200 (9/15)

Advertisement

loading

Summary of Contents for NORTH COAST ROCKETRY HyperSwift SR-99

  • Page 1 •  North Coast rocketry shall not be held responsible for personal injury or property damage resulting from the use of our product. The buyer assumes all risks and liabilities arising from the use of our product and uses our product on these conditions.
  • Page 2: Parts List

    Before You Start: Parts List Thank you for purchasing this North Coast Rocketry® model kit. We hope you have an enjoyable time constructing and flying this model rocket. Please read all of these instructions to become familiar with them before starting construction. The...
  • Page 3 Crimp the loop/sleeve connector with a as possible afterwards. crimping tool or a pair of pliers. Apply a drop of CA to the joint. Copyright © 2012, 2015 North Coast Rocketry®. All rights reserved  ...
  • Page 4 If your plywood parts are warped, place them under a stack of books for 24-48 hours to flatten them. Copyright © 2012, 2015 North Coast Rocketry®. All rights reserved  ...
  • Page 5 Test fit the wing on the airframe assembly. Align the aft edge of the wing with the ½” alignment mark on the airframe tube. Using epoxy, bond the wing in place. Copyright © 2012, 2015 North Coast Rocketry®. All rights reserved  ...
  • Page 6 Glue the others on as shown. □ Glue the launch lugs on under the wing at the aft and leading edges on both sides. Fillet the joints with epoxy. Copyright © 2012, 2015 North Coast Rocketry®. All rights reserved  ...
  • Page 7 North Coast Rocketry Copyright © 2012, 2015 North Coast Rocketry®. All rights reserved  ...
  • Page 8 North Coast Rocketry Copyright © 2012, 2015 North Coast Rocketry®. All rights reserved  ...
  • Page 9: Flight Preparations

    The recovery system permits the safe landing of the model to the ground. Fly safely and have fun! Copyright © 2012, 2015 North Coast Rocketry®. All rights reserved  ...
  • Page 10 Minimum Site Dimensions (ft.) 0.00--1.25 1/4A, 1/2A 1.26--2.50 2.51--5.00 5.01--10.00 10.01--20.00 20.01--40.00 1,000 40.01--80.00 1,000 80.01--160.00 1,000 160.01--320.00 Two Gs 1,500 Join the National Association of Rocketry! Visit www.nar.org for details! Copyright © 2012, 2015 North Coast Rocketry®. All rights reserved  ...