We are not liable for any substantial accident and/or damage. Before you drive this machine or start the engine of the Kersten machine that you are handling, we ask that you urgently to make yourself familiar with this manual and the operation of the machine.
The manual assumes that the operator has a general awareness for Health and Safety to be appointed an operator in the first place. This Kersten machine has been designed, so far as is reasonably practical, So that it will not endanger the safety of the operator or anyone else if the...
General safety and accident prevention instructions: ● Consider all additional valid general operating instructions and health and safety regulations ● This machine should not be operated by any person under the age of 16. ● This machine may be subject to regulations when used on the public highway ●...
Safety Attention! This machine is equipped with warning symbols (safety decals). Be aware of your safety at all times when operating a machine. Real security means that you are familiar with all safety decals. These decals indicate types and areas of endangerment and in particular the safety measure which should be taken.
Basic Rules ● Always use the machine across the slope in preference to going up and down Use extreme caution when changing direction on a slope ● Do not operate this machine on slopes of more than 20 degrees ...
This device must be disposed of according to the regulation of the municipality or the country. All possible parts should be recycled and the remainder disposed of in a satisfactory manner. The company Kersten Maschinenvertriebs GmbH or Kersten (UK) Ltd does not take responsibility of disposal. Warranty Details of Warranty are included on the warranty registration form.
Assembly Assembly Dirt collector Attach left and right hand collector height adjustment brackets to the front of the sweeper housing using counter sunk screws and lock nuts. Attach the collector to the sweeper by folding the catch lever up. Slide the container down on to the two adjustable hooks and fold the catch lever down to lock in to place.
Page 10
Assembly - side broom When attaching the side brush to the sweeper housing for the first time the drive pulley and support casing needs to be fitted to the right hand of the sweeper housing as viewed from the operating position. Remove the 17mm clamping bolt, discard the flat washer.
Page 11
Adjustment possibilities with the side broom "H" = height adjustment of the side broom is made by turning grasp “H”. Anti- clockwise lowers the brush for more contact with the ground. Clockwise raises the brush for less contact with the ground. Please note that adjusting the height of the main brush will affect the height setting of the gulley brush!! “N”...
Page 12
The 5 litre water tank bracket should be mounted on the right of the handle bar upright of the K2000 2 x 8.5mm holes must be drilled 170mm from each other and 260mm from the top along the centre line of handlebar upright.
Operation Operating instructions – power unit: Adjusting handlebars : Loosen the 17 mm screws in elongated slots, one each side of the control console. Adjust the handlebars to the desired height and retighten screws. Engine : Please use engine manufacturers information from the enclosed operating instructions for this.
Page 14
Operating instructions to Sweeping machine: Height adjusters “A” control the brush depth settings . Twisting them clockwise will lower the brush – anticlockwise will raise the brush. The base setting from which to work is when 40mm of the brush is in contact with the surface to be swept.
Maintenance General information Note! Injuries to people or Damages to the machine can occur. You should check before each use that the machine is safe and the relevant parts and hydraulic connections are properly connected. Maintenance ● The sweeping machine must be submitted to regular maintenance. ●...
Page 16
Installing a replacement sweeping brush Remove the 17mm long clamping bolt from the sweeping machine housing Loosen the three screws on the bearing housing and remove clamp and bearing assembly. Take the square drive tube out of the two sectioned sweeping brush and remove brushes.
Technical Data: Power Unit: Engine: Honda four-cycle petrol engine 6,6kW (9PS) Regular grade fuel, lead free Option of electric start model as above = K 2000/E Transmission: Hydrostatic with differential axle Infinitely variable speed adjustment Adjustable handlebar Hydraulic drive for attachments with infinitely variable speed Equipment quick attach system Forward 0 to 7 km/h (infinitely variably) Backwards 0 to 3.5 km/h...
Conformity explanation Conformity explanation of the manufacturer (article 8 that Guideline 98/37/EG) Kersten Maschinen – Vertriebs GmbH Empeler road 93-95 D - 46459 R e e s explain that the machine Hand-guided front sweeping machine with combustion engine Fabrikmarke: Kersten...
Page 29
Sweeping Machine-Accessories (Plastic-Collector Box from 04/2001!) 90a = 712 100 216 Suspension rod 1,00m 1,25m 90b = 712 125 216 Suspension rod Nr. Part-Nr. Qty Description Nr. Part-Nr. Qty. Description 48a 712 100 094 Spray guard 1,00m 926 301 076 Caster 48b 712 125 094 Spray guard 1,25m...
Page 30
FKM 1050 and FKM 1255 : Brushes a) Brush - 37 cm diameter b) Brush - 45 cm diameter Part Description Part-Nr. Dirt Brush-Poly ith full Poly-trimming a) For FKM 1050 in 100 cm 1005 160 / 370 a) For FKM 1255 in 125 cm 1255 160 / 370 b) For FKM 1050 in 100 cm 1005 160 / 450...
Page 31
Spare parts-list Side-Brush from 07/01, Nr. Bestell-Nr. Anz. Bezeichnung Nr. Bestell-Nr. Anz Bezeichnung 1 105 000 120 Driving pulley 23 907 155 000 Quick lock pin 2 905 010 000 Lockwasher 24 105 000 126 Side broom arm part of 4 3 105 000 121 Mounting plate 25 901 110 150...
Page 32
Parts catalog Option: Lighting elements Nr. Bestell-Nr. Anz. Bezeichnung Nr. Bestell-Nr. Anz. Bezeichnung 1 920 000 102 Hondamotor 9PS+Lichtspule 13 911 010 028 Rubber metal buffer 1a 920 000 004 Hondamotor 9PS with E-start 14 901 010 016 screw 2 700 000 050 Owner for hydraulic hoses 15 905 010 000 Lock washer...