Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for in.hub HUB-GM200
- Page 1 USER MANUAL IoT Gateway HUB-GM200 Version 1.1 / 26.06.2023...
-
Page 2: Table Of Contents
5.1.7 LED display ............................16 5.1.8 Backplane bus ..........................16 Connecting the HUB-GM200 to the power supply................16 First steps with SIINEOS ......................17 Connecting the HUB-GM200 with your PC ..................... 17 Logging in to SIINEOS ..........................18 Checking the SIINEOS version ........................19 Updating SIINEOS ............................ -
Page 3: Legal Notes
Legal Notes 1 Legal Notes Warning concept This manual contains information that you must observe for your personal safety and to prevent damage to property. Depending on the hazard level, the warnings are presented in decreasing order as follows: DANGER Indicates a direct hazard for humans. - Page 4 If third-party products and components are used, they must be recommended or approved by in.hub. Proper storage, installation, commissioning, and operation are essential for the correct and safe operation of the product.
-
Page 5: General Information
General information 2 General information This Instruction Manual contains information for commissioning and using the HUB-GM200 gateway. The manual is intended for installers, programmers, and testers who commission the gateway and connect it to other units (automation systems, mobile terminals, personal computers, etc.), and for service technicians who install extension modules or perform... -
Page 6: Network Security
General information 2.5 Network Security Please keep in mind that the product does not communicate encrypted within the internal network. Therefore, protect your network against unauthorized access from outside! The integration into a network with Internet access must be carried out with special care. For this, urgently talk to your system administrator in advance. -
Page 7: Product Information
The HUB-GM200 is primarily used on the sales floor to control and connect the field level and the control level with the operational-management level and the company level. It is also used for individual monitoring, specifically to monitor, manage, and control processes in a closed loop. -
Page 8: Hardware - Structure And Interfaces
Product information 3.2 Hardware - Structure and interfaces Fig. 1: Side views and front view of the HUB-GM200 Device-specific information is encoded in a barcode: HW: Hardware revision number S/N: in.hub-internal serial number MAC: Hardware address of the Ethernet 1 and 2 network adapters... -
Page 9: Led Display
Device error 3.4 SIINEOS - System Software The HUB-GM200 uses the Linux-based operating system SIINEOS to run InCore & Docker Apps. SIINEOS is accessible via a management console (SMAC) and can be configured there. All network parameters are also set up here to enable communication with other... -
Page 10: Installation
Installation 4 Installation The HUB-GM200 is intended for installation on a DIN rail compliant with DIN EN 60715:2017. Always switch the power supply off. • WARNING Electrical shock due to conductive contamination can cause physical injury! Avoid conductive contamination. -
Page 11: Mounting Add-On Modules
2. Plug the backplane bus connector belonging to the add-on module to the backplane bus interface of your module. 3. Click the add-on module onto the DIN rail and push it up to the HUB-GM200 so that the pins of the two backplane bus connectors interlock. -
Page 12: Commissioning
Machinery Directive. Interfaces of the HUB-GM200 The following section gives an overview of the interfaces of the HUB-GM200 and provides information you need to connect these interfaces. For the position of the interfaces at the module, please refer to the section Hardware - Structure and interfaces, page 8. -
Page 13: Can
Commissioning 5.1.4 NOTE: By default, a termination is set for the CAN interface. Therefore, attach the module at the end of a bus structure and switch over the devices, which formed the termination until then. Voltage output = 24 V / 0.7 A, protected against reverse polarity and overload •... -
Page 14: Rs485
Commissioning 5.1.5 RS485 NOTE: By default, a termination is set for the RS485 interface. Therefore, attach the module at the end of a bus structure and switch over the devices, which formed the termination until then. Voltage output = 24 V / 0.7 A, protected against reverse polarity and overload •... -
Page 15: Io1 And Io2
Commissioning 5.1.6 IO1 and IO2 The pins of the IO1 and IO2 interface can be configured in SIINEOS as digital input or digital output. Fig. 8: Schematic drawing of the IO1 and the IO2 interface Pins Signal IO1 Signal IO2 Description GND 1 GND 1... -
Page 16: Led Display
Voltage of the backplane bus = 24 V • 5.2 Connecting the HUB-GM200 to the power supply Precondition: The module is mounted correctly on the DIN rail. See chapter Mounting and dismounting the module at the DIN rail, page 10. -
Page 17: First Steps With Siineos
Connecting the HUB-GM200 with your PC Connect your PC to the USB1 interface on the front of the HUB-GM200 using a micro- USB cable. In most cases, the USB port provides sufficient power to operate the HUB-GM200 without having to connect an extra power supply. -
Page 18: Logging In To Siineos
First steps with SIINEOS 6.2 Logging in to SIINEOS NOTE: The latest versions of Firefox, Edge or Chrome browsers are recommended for SIINEOS. Using other or older browsers may cause compatibility issues. NOTE: Make sure that the gateway is connected to the PC. When you log in to SIINEOS for the first time Enter the following address in your browser: http://192.168.123.1/smac... -
Page 19: Checking The Siineos Version
First steps with SIINEOS 6.3 Checking the SIINEOS version Go to the SIINEOS start page by selecting the Overview page on the left. Fig. 12: "Overview" page with the SIINEOS version (example) 2. Check the SIINEOS version field to see which version is installed on your gateway. 3. -
Page 20: Updating Siineos
First steps with SIINEOS 6.4 Updating SIINEOS Go to the https://download.inhub.de/siineos/ page and select the current SIINEOS package. Two variants are available: the complete software package and a light variant with no Docker container and with a smaller file size. 2. -
Page 21: Technical Data
Technical data 7 Technical data Data Values Voltage range of the power 24 V ± 10 % | reverse polarity protected and overload supply protected Max. Power consumption 120 W (total device) Processor Colibri IMX7D 1 GB 32-bit, 2 x ARM Cortex-A7 CPU ARM®, 1 x Cortex-M4 CPU Cores®, Cryptographic Acceleration and Assurance Module, Secure Real-Time Clock Memory... -
Page 22: Eu Declaration Of Conformity
EU Declaration of Conformity 8 EU Declaration of Conformity... - Page 23 EU Declaration of Conformity...
- Page 24 EU Declaration of Conformity...