1. Manuals
  2. Brands
  3. SELT Manuals
  4. Tent
  5. V ZIIIP
  6. Installation manual

SELT V ZIIIP Installation Manual

Veranda/pergola
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
5.7
DT-E
TECHNICAL AND OPERATIONAL DOCUMENTATION
INSTALLATION MANUAL,
OPERATING MANUAL AND INSTRUCTIONS FOR SAFE USE
(Translated from the original manual)
5. Steel and aluminium components and structural sets
5.7. Veranda V ZIIIP / Pergola V ZIIIP

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the V ZIIIP and is the answer not in the manual?

Questions and answers

Related Manuals for SELT V ZIIIP

Summary of Contents for SELT V ZIIIP

  • Page 1 DT-E TECHNICAL AND OPERATIONAL DOCUMENTATION INSTALLATION MANUAL, OPERATING MANUAL AND INSTRUCTIONS FOR SAFE USE (Translated from the original manual) 5. Steel and aluminium components and structural sets 5.7. Veranda V ZIIIP / Pergola V ZIIIP...
  • Page 2 Is valid from: 01 March 2021  Is applicable to the above listed product versions. Translated from the original manual DT-E 5.7: SYSTEM VERANDA V ZIIIP – SYSTEM PERGOLA V ZIIIP Edition 3 / March 2021 / EN page 2 / 40...

  • Page 3: Table Of Contents

    PRODUCT COMPLIANCE WITH THE CE STANDARD ....................39 10.2 INFORMATION ACCOMPANYING THE CE MARKING ..................... 39 Translated from the original manual DT-E 5.7: SYSTEM VERANDA V ZIIIP – SYSTEM PERGOLA V ZIIIP Edition 3 / March 2021 / EN page 3 / 40...

  • Page 4: Introduction

    Marking of electronic or electric equipment, which should be collected in the ENVIRONMENT designated points. Translated from the original manual DT-E 5.7: SYSTEM VERANDA V ZIIIP – SYSTEM PERGOLA V ZIIIP Edition 3 / March 2021 / EN page 4 / 40...

  • Page 5: Terms And Definitions

    Veranda V ZIIIP multi-module with mounting brackets – a sun protection system consisting of a structure of two or more single-module veranda awnings joined together, supported on a load-bearing surface by means of common mounting brackets supporting the side guides and independent cassette mounting brackets, consitutitng one joint product.

  • Page 6: Subject, Intended Use And Contents Of The Documentation

    Copyrights for this documentation remains with SELT Sp. z o.o. with its registered office in Opole. This documentation may not be used in any way, either in whole or in part, without the permission of SELT Sp. z o. o.

  • Page 7: Product Technical Information

    Technical specifications of the product are available after logging in on website www.selt.com TECHNICAL PARAMETERS : Veranda V ZIIIP - single-module veranda version with guide rail brackets Translated from the original manual DT-E 5.7: SYSTEM VERANDA V ZIIIP – SYSTEM PERGOLA V ZIIIP...
  • Page 8 Pergola V ZIIIP – terrace awning version single-module with front posts Translated from the original manual DT-E 5.7: SYSTEM VERANDA V ZIIIP – SYSTEM PERGOLA V ZIIIP Edition 3 / March 2021 / EN page 8 / 40...
  • Page 9 - To the ground or to the wall (structural element) and the ground Translated from the original manual DT-E 5.7: SYSTEM VERANDA V ZIIIP – SYSTEM PERGOLA V ZIIIP Edition 3 / March 2021 / EN page 9 / 40...

  • Page 10: Product Specification

    Detailed data for parameters of the individual motors are available on the websites of motor manufacturers and on the website: https://www.selt.com/automatyka-en PRODUCT SPECIFICATIO N Products manufactured by SELT Sp. z o. o. have appropriate technical and operational parameters. List of product types:  Installed outside the building, started by electromechanical drive connected with the control system, ...

  • Page 11: Transport And Storage Of The Product

    COMPLETENESS AND QUALITY CONDITION OF TH E DELIVERY SELT Sp. z o. o. makes every effort to ensure compliance of the goods with the order. However, checking the completeness of the product is the responsibility of the Buyer and should take place at the time of its receipt. Discrepancies should be immediately reported to the driver/warehouseman/assembly team and marked on the WZ document under pain of loss of claims in this respect.

  • Page 12: Product Installation

    This chapter contains general requirements concerning the product installation. Correct assembly is a necessary condition for smooth operation of the product. SELT Sp. o.o. recommends using only professional assembly crews, which guarantee the Purchaser that the conducted installation will be correct.

  • Page 13: Preparation For Installation

    The carrier is responsible for damage caused in transit. For the installation of Pergola V ZIIIP, we distinguish four installations for different types of the product: ...

  • Page 14: Brackets - Dimensions

    Horizontal cassette bracket Transverse guide rail bracket (Type D) Guide rail bracket (Type A) Translated from the original manual DT-E 5.7: SYSTEM VERANDA V ZIIIP – SYSTEM PERGOLA V ZIIIP Edition 3 / March 2021 / EN page 14 / 40...
  • Page 15 Note: The bracket can be used for max. 19,5 m2 of cover area. 7. Modular transverse guide rail bracket (Type G) Translated from the original manual DT-E 5.7: SYSTEM VERANDA V ZIIIP – SYSTEM PERGOLA V ZIIIP Edition 3 / March 2021 / EN page 15 / 40...

  • Page 16: Installation - Version With Brackets

    3. Install the complete cassette (2) on the cassette mounting brackets (1) in the direction of the arrow. Fig. 3 Translated from the original manual DT-E 5.7: SYSTEM VERANDA V ZIIIP – SYSTEM PERGOLA V ZIIIP Edition 3 / March 2021 / EN page 16 / 40...
  • Page 17 Note: for modular assembly, use modular rail brackets (12) - as shown in the picture: Translated from the original manual DT-E 5.7: SYSTEM VERANDA V ZIIIP – SYSTEM PERGOLA V ZIIIP Edition 3 / March 2021 / EN page 17 / 40...
  • Page 18 - the drawing shows the approximate spacing and quantity. Fig. 10 Translated from the original manual DT-E 5.7: SYSTEM VERANDA V ZIIIP – SYSTEM PERGOLA V ZIIIP Edition 3 / March 2021 / EN page 18 / 40...
  • Page 19 (13) in the guide (10). Repeat the steps for both guides. Fig. 12 Translated from the original manual DT-E 5.7: SYSTEM VERANDA V ZIIIP – SYSTEM PERGOLA V ZIIIP Edition 3 / March 2021 / EN page 19 / 40...
  • Page 20 (17) with screws (16) M5x10 ISO-10642. Repeat the steps in the same way for the remaining guides. Translated from the original manual DT-E 5.7: SYSTEM VERANDA V ZIIIP – SYSTEM PERGOLA V ZIIIP Edition 3 / March 2021 / EN...
  • Page 21 (21). The belt (21) should be connected in such a way that the belt, velcro and Velcro tape are not overlapped at the joint. Translated from the original manual DT-E 5.7: SYSTEM VERANDA V ZIIIP – SYSTEM PERGOLA V ZIIIP Edition 3 / March 2021 / EN page 21 / 40...
  • Page 22 - in accordance with the instructions for use for the motor - Fig. 20. Fig. 20 Translated from the original manual DT-E 5.7: SYSTEM VERANDA V ZIIIP – SYSTEM PERGOLA V ZIIIP Edition 3 / March 2021 / EN page 22 / 40...

  • Page 23: Installation - Wall Version (With Front Posts)

    24. Install anchors (a) selected for the type of substrate - fig.24. Tighten the cassette mounting brackets (1). Fig. 24 Translated from the original manual DT-E 5.7: SYSTEM VERANDA V ZIIIP – SYSTEM PERGOLA V ZIIIP Edition 3 / March 2021 / EN page 23 / 40...
  • Page 24 Maximum diameter of the threaded part M10. Fig. 29 Translated from the original manual DT-E 5.7: SYSTEM VERANDA V ZIIIP – SYSTEM PERGOLA V ZIIIP Edition 3 / March 2021 / EN page 24 / 40...
  • Page 25 (14A) M8 ISO-4762 and the nut (14B) M8 ISO-10511 - fig. 32. Fig. 32 Translated from the original manual DT-E 5.7: SYSTEM VERANDA V ZIIIP – SYSTEM PERGOLA V ZIIIP Edition 3 / March 2021 / EN page 25 / 40...
  • Page 26 (12) with screws (18) M5x10 ISO-10642. Repeat the steps in the same way for the remaining guides. Translated from the original manual DT-E 5.7: SYSTEM VERANDA V ZIIIP – SYSTEM PERGOLA V ZIIIP Edition 3 / March 2021 / EN...
  • Page 27 ! The belt must be routed over the roller! Fig. 37 Translated from the original manual DT-E 5.7: SYSTEM VERANDA V ZIIIP – SYSTEM PERGOLA V ZIIIP Edition 3 / March 2021 / EN page 27 / 40...
  • Page 28 NOTE: remember to release the belt lock (25) by pressing the buckle in the front beam (arrow). Fig. 40 Translated from the original manual DT-E 5.7: SYSTEM VERANDA V ZIIIP – SYSTEM PERGOLA V ZIIIP Edition 3 / March 2021 / EN page 28 / 40...
  • Page 29 (7) for about 15 seconds in order to glue these elements together - fig. 44. Fig. 44 Translated from the original manual DT-E 5.7: SYSTEM VERANDA V ZIIIP – SYSTEM PERGOLA V ZIIIP Edition 3 / March 2021 / EN page 29 / 40...

  • Page 30: Electric Drive

    4.7.1 CONNECTION TO ELECTR ICAL INSTALLATION When the Pergola V ZIIIP is assembled one should proceed to connection of drive and control system to the previously prepared systems: electrical supply installation and control system. Connection to the power supply electrical system should be made on the basis of a previously prepared individual wiring diagram, taking into account the recommendations contained in the operation and maintenance manual of the motor driving the product.

  • Page 31: System Operation And Product Safety

    GENERAL REQUIREMENTS FOR OCCUPATIONAL HEALTH AND SAFETY  To ensure correct operation of the product SELT Sp. z o.o. forbids making any structural changes; non-observance of the above condition releases the manufacturer from the liability for the product and the warranty will be invalidated.

  • Page 32: Misuse Of The System

     In the event of loss of belt tension in the guides, it is recommended to contact Selt service for re-tensioning. In the case of loosening the belt (an action not performed by the Customer), use force to press the belt buckle lock in the front beam.

  • Page 33: System Use And Maintenance

    If the product is used in a manner other than described in this documentation or modified without the authorization of SELT Sp. z o. o. then it is misused. Unauthorized changes affecting the operational safety of the product are not allowed.

  • Page 34: Instruction For Non-Professionals

    Due to the safety of users and the maximum long, correct operation of all mechanisms, the product should be subjected to periodic technical inspections at least every 12 months.  It is recommended to carry out periodic inspections of products by SELT Sp. z o.o.  Inspections are performed for a charge.

  • Page 35: Maintenance

    Replace the plug and secure it with an ISO-7045 screw and an ISO 7050 screw. Translated from the original manual DT-E 5.7: SYSTEM VERANDA V ZIIIP – SYSTEM PERGOLA V ZIIIP Edition 3 / March 2021 / EN page 35 / 40...

  • Page 36: General Product Information

    Drive belt The drive belt is an exploitative element in the Pergola V ZIIIP system. During the use of the system, minor abrasions of the side edge of the belt may occur. It is recommended to replace the belt after about 2 - 3 thousand cycles.
  • Page 37 Damage caused by using the system in inappropriate weather conditions.  Differences in the operation of Pergola V ZIIIP systems in the module and placed directly next to each other. The described phenomenon does not affect the proper functioning of Pergola V ZIIIP.

  • Page 38: Complaint / Technical Defects

    SELT Sp. z o.o. in Opole.  notifications can be sent to the e-mail address reklamacje@selt.com or directly to a sales representative. Reporting a technical defect / complaint should be made in writing on the "complaint notification" form, which can be found at www.selt.com/doc.pl or directly to the sales representative.

  • Page 39: Marking And Labelling The Product With The Ce Mark

    - it is forbidden to load the movable part of the roof with snow - roof angle from 10 to 45 degrees from the horizontal plane (Pergola V ZIIIP version) or from 0 to 45 degrees (Veranda V ZIIIP version),...
  • Page 40 – given in tables on the website of the manufacturer Translated from the original manual DT-E 5.7: SYSTEM VERANDA V ZIIIP – SYSTEM PERGOLA V ZIIIP Edition 3 / March 2021 / EN page 40 / 40...

Table of Contents