Related Manuals for Ascot 302-05605
Summary of Contents for Ascot 302-05605
- Page 1 OPERATING MANUAL ASCOT SUPPLY 3-1/2-TON FLOOR JACK 302-05605 AS5605 MAKE SURE TO READ AND FULLY UNDERSTAND THE INSTRUCTION MANUAL BEFORE USING THIS PRODUCT...
-
Page 2: Table Of Contents
TABLE OF CONTENTS General Description & Safety ................1 Warnings ........................ 2 Assembly ........................ 3 Hydraulic System Purging ................4 Operating Instructions ..................5 Maintenance ......................6 Troubleshooting ....................7 Exploded View & Parts List ................8 Warranty Information ..................9... -
Page 3: General Description & Safety
GENERAL DESCRIPTION & SAFETY Product Description Hydraulic service jack is designed to lift, but not support, one end of a vehicle. Immediately after lifting, loads must be supported by a pair of appropriately rated jack stands. Specifications Capacity 3-1/2-Ton Minimum Height 3-3/4”... -
Page 4: Warnings
WARNINGS 1) Locate the jack in a suitable working area. 2) Inspect the jack before each use. Do not use jack if damaged, altered, modified, in poor condition, leaking hydraulic fluid or unstable due to loose or missing hardware or parts. Make corrections before using. 3) Use jack on level and solid ground, preferably concrete. -
Page 5: Assembly
ASSEMBLY Important Receiving Instructions Visually inspect all components for shipping damage. If any shipping damage is found, notify carrier at once. Shipping damage is NOT covered by warranty. The carrier is responsible for all repair and/or replacement cost resulting from damage in shipment. Check the parts in the carton. -
Page 6: Hydraulic System Purging
HYDRAULIC SYSTEM PURGING To purge hydraulic system: 1. Open the release valve by turning it two full turns counter-clockwise. 2. Quickly pump the handle a minimum of four full strokes. 3. Close the release valve by turning it clockwise. 4. Pumping the handle with full strokes to check if it can reach the maximum height by ten pumps. If it can’t reach the maximum height by ten pumps, please refer to the following special purging process: 5. -
Page 7: Operating Instructions
OPERATING INSTRUCTIONS Lifting a Vehicle 1. Ensure that the jack and the vehicle are on a hard, level surface. 2. Always ensure that the vehicle’s parking brake is engaged and that the vehicle’s wheels are chocked. 3. Consult the vehicle’s owner’s manual to determine the location of jacking points. Position the jack under a suitable lifting point. -
Page 8: Maintenance
MAINTENANCE Monthly Maintenance Lubrication is critical to jacks, since they support heavy loads. Any restriction due to dirt or rust can cause either slow jack movement or extremely rapid jerks, causing damage to the internal components. To keep the jack well lubricated, carry out the following steps. 1. -
Page 9: Troubleshooting
TROUBLESHOOTING PROBLEM CAUSE REMEDY Jack will not lift to full height 1. Oil level low 1. Check / add oil 2. Release valve not closing 2. Close the release valve Jack will not hold the load 1. Release valve not closing 1. -
Page 10: Exploded View & Parts List
EXPLODED VIEW & PARTS LIST DESCRIPTION QUANTITY DESCRIPTION QUANTITY HANDLE ASSEMBLY FRAME ASSEMBLY HANDLE SLEEVE ADJUST SCREW PEDAL RETAINING RING HEX BOLT WASHER LOCK WASHER FIXED WHEEL PEDAL BASE RIGHT ADJUSTABLE PLATE PUMP CORE WHEEL RETAINING RING PUMP ASSEMBLY RETAINING RING SPRING HANDLE BASE RETAINING RING... -
Page 11: Warranty Information
WARRANTY INFORMATION ONE YEAR LIMITED WARRANTY For a period of one (1) year from your purchase date, distributor will repair or replace (at its option), without charge, your product if it was purchased new and the product has failed due to a defect in material or workmanship which you experienced during normal use of the product.
Need help?
Do you have a question about the 302-05605 and is the answer not in the manual?
Questions and answers