Table of Contents
Advertisement
Quick Links
Electric Tracked Dumper
Operator's Manual
READ AND UNDERSTAND THE ENTIRE MANUAL
READ AND UNDERSTAND THE ENTIRE MANUAL
READ AND UNDERSTAND THE ENTIRE MANUAL
Ensure you read and understand how to operate
BEFORE OPERATING THIS MACHINE
the machine safely. Check your machines oil
BEFORE OPERATING THIS MACHINE
BEFORE OPERATING THIS MACHINE
MD450E
FOR YOUR SAFETY
FOR YOUR SAFETY
FOR YOUR SAFETY
FOR YOUR SAFETY
levels before every use.
Distribution Limited
Advertisement
Table of Contents
Related Manuals for Lumag MD450E
Summary of Contents for Lumag MD450E
- Page 1 Distribution Limited Electric Tracked Dumper Operator’s Manual MD450E FOR YOUR SAFETY FOR YOUR SAFETY FOR YOUR SAFETY FOR YOUR SAFETY READ AND UNDERSTAND THE ENTIRE MANUAL READ AND UNDERSTAND THE ENTIRE MANUAL READ AND UNDERSTAND THE ENTIRE MANUAL Ensure you read and understand how to operate BEFORE OPERATING THIS MACHINE the machine safely.
- Page 3 All Other Moving Parts & Lubricate X (2) Cables 1 – First service only, 2 = Should be carried out by your Lumag Dealer, 3 = May need to be done more often in dusty areas & 4 = Replace paper element only...
-
Page 5: Table Of Contents
CONTENTS / INFORMATION ON OPERATING INSTRUCTIONS CONTENT INFORMATION MANUAL INFORMATION MANUAL These operating instructions contain important DELIVERY information on how to handle electrical Dumper / ASSEMBLY trolleys. Requirement for safe operation is the HANDLEBARS INDEXING correct observance of all specified safety and KIPPMULDE MOUNT handling instructions. -
Page 6: Delivery
DELIVERY / ASSEMBLY DELIVERY 3. Now screw the struts (D) with two screws (3) and nuts (7) by strutting between the frame and the control unit (C). Check the contents of the box / shipping box for completeness and possible transport damage after unpacking. -
Page 7: Intended Use
MOUNTING / DETERMINATIONS The machine is used for transporting goods of various kinds used horticulture, agriculture, civil engineering, from demolition and renovation work, even indoors. The machine is driven by an electric motor with gearbox and differential. Its speed and thus the traveling speed and direction of travel is adjusted by means of throttle lever or a directional switch via the integrated control. -
Page 8: Technical Specifications
SPECIFICATIONS / ENVIRONMENT / SYMBOLS TECHNICAL SYMBOLS SPECIFICATIONS MACHINE model MD-450E machine symbols attached. These power 800 watt represent important information is on the product or nominal voltage 60 volt usage instructions. Drive / battery 5x12V,20Ah charging time Approx. 7 hours WATCH OUT! (with completely This is about your personal safety. -
Page 9: Batteries
SECURITY In the working area is sufficient space BATTERIES respect, think highly of. Attention, Tripping Rechargeable batteries / cells are very hazard! Disorder can lead to accidents. heavy! Ensure secure installation! Explosion and fire hazard, shorts! Bystanders keep. WATCH OUT! Metal parts of the battery cell are always live, so do not place foreign objects or tools on the battery. -
Page 10: Security
SECURITY SECURITY BATTERIES / CHARGER This section gives a comprehensive overview of all Use and care of batteries and chargers important safety aspects for optimal protection of the operator, as well as safe and trouble-free Batteries and chargers are not toys and should be operation. -
Page 11: Safety
SECURITY Make sure that the machine is turned off before First time users should be instructed by the seller to installing batteries. The insertion of the battery in a familiarize yourself with the characteristics of the machine that is turned on can lead to accidents. engine operated machine, the intended use and the necessary safety devices. - Page 12 SECURITY use the machine for purposes for which it was not and not tip during operation, rolls, intended (see "Intended Use"). may slip or fall. The effectiveness of the controls may not Keep hands, feet, loose clothing and body jewelry be unduly influenced or canceled.
-
Page 13: Safety In The Use And Care Of The Machine
Moisture away from live parts. This can cause a this manual. All other work must be carried out by a short circuit. specialist workshop or LUMAG service workshop. diving The machine, the power cable or connections in water or other liquids. Keep handles dry, clean be installed by qualified electricians working on the and free of debris. -
Page 14: Residual Risks And Protection Measures
SECURITY Transport them never people, children, house Was standing. or farm animals with the machine. Bumps, drops, vibrations Sloppy passing the machine can cause destruction of the battery and cause serious injury. Never transport them dangerous items or materials with the machine. →... -
Page 15: 8.8 Behavior In Case Of Emergency
PARTS NAME, FUNCTION 8.8 BEHAVIOR IN CASE OF EMERGENCY Battery indicator (6) The state of charge indicator shows the remaining possible accident, initiate charge in the battery. corresponding necessary first-aid measures and request as soon as possible qualified medical help. When calling for help, give the following information: where it happened - what happened - how many... -
Page 16: Transport,Put Up
PARTS NAME, FUNCTION Transmission lever (9) Charging socket for batteries (12) With this lever the translation and thus the speed of This charging connector is used for charging the the mini-dumper can be adjusted. There are two batteries, which are installed below the trough. To levels: LOW = low and HIGH = high transmission load flip open the socket and connect the included speed. -
Page 17: Business
TRANSPORT, INSTALLATION / OPERATION BUSINESS accumulators The batteries of the machine are in mint condition for about 60 to 70% charged. The batteries must be 11.1 GETTING STARTED charged before using the machine. Before putting the machine into operation, read Please study these instructions carefully. -
Page 18: Turning And Driving
BUSINESS 11.2 TURNING AND DRIVING 11.3 BRAKE SYSTEM 1. The ignition key (10) is in OFF The machine is equipped with a mechanical drum brake, which locks the chain in the park or non-use Position. position. machine from rolling thus 2. -
Page 19: Loading And Discharge Of
BUSINESS 11.5 LOADING AND DISCHARGE OF CARGO 11.6 BATTERIES CHARGE Loaded When loading to a safe state of the machine and secure anchoring transported goods. In front sure to stop the drive of the store and Distribute the transported goods evenly in the well. remove the key! To charge the batteries, the Do not overload the machine! The max. - Page 20 BUSINESS Connect the charger of the machine only to a When charging the batteries explosive gas properly installed and grounded outlet. mixtures. Make sure that the charger and the batteries are well ventilated during charging. Avoid overcharging and deep discharge Open fire or smoking during the batteries.
-
Page 21: Checks
OPERATION / CONTROLS CHECKS The commitment damaged Regular checks are essential if the machine is to electric wire injury or remain a reliable working tool. electric shock to lead. Prior checks on the machine, the drive Pull off and key! The machine from the power supply! –... -
Page 22: Maintenance
Check charger, cable and plug before each use. Do If the batteries are no longer functional, please not use the charger if there is damage. Open the contact an authorized dealer or the LUMAG service charger itself and have it repaired by qualified team. -
Page 23: Transmission
MAINTENANCE Use suitable gloves when disposing of the defective 13.3 ENGINE battery. Dispose of defective batteries in an environmentally friendly through the authorized The engine is equipped with carbon brushes. collection points. The disposal in the household waste is prohibited! These carbon brushes regularly - all are checked for abrasion and wear - 50 hours. -
Page 24: Storage
MAINTENANCE / STORAGE STORAGE If the machine is not used for a long time, the following points under all circumstances should be considered: When stored for several days up to a month It is recommended to leave the batteries on the charger only when the machine (several days) to be used in the foreseeable future. -
Page 25: Trouble
TROUBLE TROUBLE disorder root cause remedy not turned key switch turn on Machine does not move faulty fuse Check fuses or bring too little power The travel direction switch is not in tilt driving direction switch to position the desired position batteries flat Charging the batteries No display on the battery... -
Page 26: Warranty Warranty / Service
SERVICE NUMBER to ensure fast classification. The guarantee will not apply in respect of the parts Warranty work be carried out by our LUMAG when defects caused by natural wear, temperature, service workshop. Possible defects within the... - Page 27 EC DECLARATION OF CONFORMITY EC DECLARATION OF CONFORMITY Under the terms of EU Directives Machinery Directive 2006/42 / EC explains the company: LUMAG GmbH Rudolf-Diesel-Str. 1a D-84375 Kirchdorf / Phone: 0049 / (0) 8571/92 556-0 Fax: 0049 / (0) 8571/92 556-19...
-
Page 28: Parts Of The Tool
PARTS OF THE TOOL PARTS OF THE TOOL... - Page 29 PARTS OF THE TOOL...
- Page 31 TROUBLE TROUBLE disorder root cause remedy not turned key switch turn on Machine does not move faulty fuse Check fuses or bring too little power The travel direction switch is not in tilt driving direction switch to position the desired position batteries flat Charging the batteries No display on the battery...
-
Page 34: Electrical Control
ELECTRICAL CONTROL... - Page 35 LUMAG GmbH Rudolf-Diesel-Str. 1a D-84375 Kirchdorf Phone: +49 (0) 85 71/92 556 - 0 Fax: +49 (0) 85 71/92 556 - 19 www.lumag-maschinen.de Status: 06/2018 - MD450E_V2...
- Page 36 Unit 1-3, Hatchmoor Industrial Estate, Hatherleigh, Okehampton, Devon EX20 3LP Lumag Distribution Limited Company Number: 09267547 VAT Number: GB154566788 Hatherleigh www.lumag-gb.co.uk 01837 811741 Plant and Tool Hire is a trading name of Lumag Distribution LTD Lumag Distribution Limited Company Number: 09267547 VAT Number: GB154566788 Hatherleigh...
Need help?
Do you have a question about the MD450E and is the answer not in the manual?
Questions and answers