Advertisement

J
Declaration of Conformity
User Manual
MPA 41xx V2.0
MPA 41xx V2.0
#298073
1 ... 16

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the MPA 41 V2.0 Series and is the answer not in the manual?

Questions and answers

Summary of Contents for Dungs MPA 41 V2.0 Series

  • Page 1 Declaration of Conformity User Manual MPA 41xx V2.0 MPA 41xx V2.0 #298073 1 … 16...
  • Page 2: Table Of Contents

    Table of contents 1. Declaration of Conformity Page 3 2. Intentionally free Page 4 3. Target group Page 5 4. Warnings 4.1 General warnings Page 5 4.2 Intended use Page 6 4.3 Risks in case of misuse Page 6 5. MPA 41xx 5.1 Approvals Page 6 5.2 Versions...
  • Page 3: Declaration Of Conformity

    Manufacturer Karl Dungs GmbH & Co. KG ▪ Karl-Dungs-Platz 1 ▪ 73660 Urbach / Germany hereby certifies that the products listed in this overview have been subjected to an EU type-examination (production type) and meet the essential safety requirements of: •...
  • Page 4: Intentionally Free

    Intentionally free 4 … 16...
  • Page 5: Target Group

    (corro- nents. sion, snow, icing, moisture No liability on the part of (e.g. due to condensation), DUNGS applies in the cases mould, UV radiation, harmful of safety-related components, The accepted rules of industri- insects and toxic, corrosive equipment and systems. Both solutions / liquids (e.g.
  • Page 6: Intended Use

    4.3 Risks in case of misuse 5.1 Approvals All settings can be found in the MPA 41xx product man- ual: www.dungs.com / ..• The equipment is reliable in operation EC type-examination certificate according to: when used normally. • Personal or consequential material •...
  • Page 7: Technical Data Mpa 41Xx

    6. Technical data for MPA 41xx 8. Inputs / outputs Protection class MPA 4112, MPA 4114 IP 54 Outputs External display IP 54 front / IP 20 rear Designation Safety- Output type Line Electrical data Protection class MPA 4122 IP 65 relevant length Ambient temperature...
  • Page 8: Assembly And Eletrical Installation

    9. Assembly and electrical installation The installation regulations applicable at the installation site must be observed. • The data specified on the rating plate must be observed to ensure safe operation • Before opening the housing, switch off the power to the system and secure it against being switched back •...
  • Page 9: Special Functions

    Installation of MPA 4112 and MPA 4114 10. Special functions Installation on DIN rail or Installation with 2x screw M4, length min. 20 mm Unlock function Drill mounting holes with 4.5 mm drill Pressing the unlock button allows the MPA to be unlocked when in a locked state. Place a sealing washer or O-ring underneath to obtain the protection class IP 54.
  • Page 10: Versions

    11. Versions 14. Connection diagram Version Voltage Display Housing design MPA 4112 and MPA 4114 MPA 4112 Integrated Luranyl MPA 4112 Integrated Luranyl MPA 4114 External Luranyl MPA 4114 External Luranyl MPA 4122 Integrated Aluminium MPA 4122 Integrated Aluminium 12. Settings Settings Seconds (s) Pre-purge time...
  • Page 11: Flame Sensor: Ionisation Electrode

    DUNGS FLW 41I 230 VAC only together with DUNGS *When using a DUNGS DEZ 1xx SEO ignition transformer for single electrode operation, shutter function the green / yellow line must be connected to terminal 5. FLW 20 (KLC 1000) KLC 10/230...
  • Page 12: Display Options

    MPA 41xx display 17. Display options Valid for internal and external display AM xx MPA 4114 minimal display Display 3 x 7 segment LED yellow LED red LED: Blue: heat request Yellow: flame quality (flashes in the case of a bad flame) Red: fault The MPA 4114 version features a minimal display of two LEDs that display the device status.
  • Page 13: Overview Of The Display Modes Mpa 4112, Mpa 4122 Am

    18. Overview of the display modes MPA 4112, MPA 4122 AM 41 18.1 Operating mode display The display can show different information Parameter switch to "Auto" depending on the operating status of the power supply "On" Waiting for safety chain automatic burner control system: with open safety chain from watchdog loading phase...
  • Page 14: Operating Information: Info Display

    Inside temperature 18.2 Operating information: info display MPA in °C At minus- The info display can be called up from the operating mode by pressing the + and Enter buttons. temperatures The information display can be used to access information about the flame quality, the resettable operating A is substituted by hours counter, the resettable start-up counter and the switching cycle counter.
  • Page 15: Error Overview - Minimal Display (Mpa 4114)

    F AA ERROR_IDLE STATE CONTROL_LDW 21. Error overview – minimal display (MPA 4114) Air pressure monitor defective, air pressure signal during idle state control, incorrect setting of air pressure monitor. F Ab ERROR_NO_AIR_PRESSURE Flashing code Error code Error description Air pressure monitor defective, air pressure signal during idle state control, incorrect setting 1 x flash F A2 Safety chain interrupted...
  • Page 16 Lagerzeiten ≤ 1 Jahr verkürzen nicht die konstruktionsbedingte Lebensdauer / Storage time ≤ 1 year does not reduce the designed lifetime / DUNGS recommends a maximum storage period of 3 years The Pressure Equipment Directive (PED) and the Directive on the energy performance Karl Dungs GmbH &...

This manual is also suitable for:

Mpa 4112 v2.0Mpa 4114 v2.0Mpa 4122 v2.0Am 41 v2.0

Table of Contents

Save PDF