i-PRO WV-QCL100-W Operating Instructions

Operating Instructions
Included Installation Instructions
Ceiling Mount Bracket
WV-QCL100-W
Model No.
WV-QCL101-W
⿟ Before attempting to connect or install this product, please read these instructions carefully
and save this manual for future use.
⿟ The external appearance and other parts shown in this manual may differ from the actual
product within the scope that will not interfere with normal use due to improvement of the
product.
i-PRO Co., Ltd. assumes no responsibility for injuries or property damage resulting
from failures arising out of improper installation, operation inconsistent with this
documentation or through use of parts other than this product, such as locally
procured parts.
For U.S. and Canada:
i-PRO Americas Inc.
For Europe and other countries:
i-PRO EMEA B.V.
https://www.i-pro.com/
© i-PRO Co., Ltd. 2022

Preface

This product is used to attach indoor dome type or PTZ type cameras to a high ceiling using a
locally procured pipe.
For the latest information about the supported cameras, refer to our support website
(https://i-pro.com/global/en/surveillance/training_support/support/technical_information <Control
No.:C0501>).

Specifications

Ambient operating temperature: –50 °C to +60 °C {–58 °F to +140 °F}
Maximum superimposed load: 88 N {19.8 lbf}
Dimensions: ø113 mm × 75 mm (H)
{ø4-7/16 inches x 2-15/16 inches (H)}
Approx. 330 g {0.73 lbs}
Mass:
Finish: Aluminum die cast
i-PRO white

Precaution

 Do not use this bracket except with suitable cameras.
Failure to observe this may cause a drop resulting in injury or accidents.
 Do not apply excessive force.
Failure to observe this may cause damage to the attaching part or a drop resulting in injury or
accidents.
 Do not attach a device exceeding the mass limit.
Failure to observe this may cause a drop resulting in injury or accidents.
Observe the mass limit.
 Refer installation work to the dealer.
Installation work requires technique and experience. Failure to observe this may cause fire,
electric shock, injury, or damage to the product.
Be sure to consult the dealer.
 I nstall the product securely on a ceiling in accordance with the installation
instructions.
Failure to observe this may cause injury or accidents.
 The measures of protection against a fall of this product shall be taken.
Failure to observe this may cause a drop resulting in injury or accidents. Be sure to install the
safety wire.
When using this product, also read the "Precautions" described in the operating
instructions for the camera to be attached.
(Pipe is locally procured)
Fs0320-3042
Printed in China
WV-QCL100-W :
ISO standard threading
WV-QCL101-W :
ANSI standard threading
Caution:
⿟ Before attempting to connect or operate this product, please read these instructions carefully.
Notice:
⿟ This product is not suitable for use in locations where children are likely to be present.
⿟ Do not install this product in locations where ordinary persons can easily reach.
⿟ For information about screws and brackets required for installation, refer to the
corresponding section of this document.

Standard accessories

Operating Instructions (this document).... 1 pc.

Other items that are needed (not included)

Fixing screws (M4)................................... 4 pcs.
Pipe ........................................................ 1 pc.
IMPORTANT
⿟ Minimum pullout strength: 196 N {44 lbf} (per 1 pc.)
⿟ This value indicates the minimum pull-out strength required value per screw. For information
about the minimum pull-out strength, refer to our support website <Control No.: C0120>.
⿟ Select screws according to the material of the location that the camera will be mounted
to. In this case, wood screws and nails should not be used.
⿟ For the safety wire specifications, refer to Step 1

Precautions for installation

 I n order to prevent injury, the product must be securely mounted to the ceiling according
to the Installation Guide of this bracket.
 Mounting method for this product
This product is designed to be used as a pendant mount camera. If the product is mounted on a
desktop or at a slant, the camera may not work correctly and its lifetime may be shortened.
 Make sure to remove this product if it will no longer be used.
<Installation example>
Compact dome type Indoor dome type
WV-S31xx series WV-S21xx series

Installation

Be sure to read "Precautions" and "Precautions for installation" before installation.
Refer to the operating instructions of the camera for details on the camera installation
(including the camera mounting, cable connection and adjustment).
This manual explains how to use this product in 2 places (one on
Step 1
the ceiling and the other on the camera).
For information about other examples of use, refer to our support
website (https://i-pro.com/global/en/surveillance/training_
support/support/technical_information <Control No.:C0508>).
【 1 】 Remove the enclosure from
the camera body.
For compact dome types and indoor
dome types of cameras, the enclosure
is removed before installation.
Refer to the parts describing
installation in the Installation Guide for
each camera for information on how to
remove the enclosure.
【 2 】 Attach the safety wire to this product (used on ceiling).
1 Prepare the safety wire by the specifications
shown in the below illustration.
Wire: ø3 mm {1/8 inches} steel
Capable of bearing 88 N
{19.8 lbf} or more.
Caulking Caulking
Total length: Pipe length + 500 mm {19-11/16 inches}
【 3 】 Attach the pipe (locally procured) to this product (used on camera).
<WV-QCL100-W>
40A R 1-1/2, 11crest, length 30 mm
{1-3/16 inches} or more (male taper pipe thread)
<WV-QCL101-W>
NPT 1-1/2, 11.5crest, length 30 mm
{1-3/16 inches} or more (male taper pipe thread)
Pipe
(locally procured)
This product (used on camera)
Fixing screws for attachment plate ........5 pcs.
(M4 x 8 mm {5/16 inches}) (of them, 1 for spare)
Safety wire .............................................. 1 pc.
【 2 】 .
Indoor 360-degree
panoramic type Indoor PTZ type
WV-S41xx series WV-S61xx series
Enclosure
<Compact dome type> <Indoor dome type>
2 Attach the safety wire to this product (used
on ceiling) as shown in the below illustration.
This
Safety wire
product
Snap hook
(locally
procured)
Recommended pipe:
ø48.6 mm {1-29/32 inches}
t = 3.5 mm {1/8 inches}
Material: Stainless Steel
Maximum permissible length:
1.5 m {59-1/16 inches}