1. Manuals
  2. Brands
  3. Gamewell Manuals
  4. Control Panel
  5. Honeywell GWF-7075
  6. Manual

Gamewell Honeywell GWF-7075 Manual

Addressable fire alarm control panel
Hide thumbs
Table of Contents

Advertisement

Quick Links

text
GWF-7075
Addressable Fire Alarm Control Panel
Manual
Document LS10147-002GF-E Rev: G
10/5/2022 ECN: 00021453

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Honeywell GWF-7075 and is the answer not in the manual?

Questions and answers

Related Manuals for Gamewell Honeywell GWF-7075

Summary of Contents for Gamewell Honeywell GWF-7075

  • Page 1 text GWF-7075 Addressable Fire Alarm Control Panel Manual Document LS10147-002GF-E Rev: G 10/5/2022 ECN: 00021453...
  • Page 2 Fire Alarm & Emergency Communication System Limitations While a life safety system may lower insurance rates, it is not a substitute for life and property insurance! An automatic fire alarm system—typically made up of smoke IMPORTANT! Smoke detectors must be installed in the same room detectors, heat detectors, manual pull stations, audible warning as the control panel and in rooms used by the system for the devices, and a fire alarm control panel (FACP) with remote...
  • Page 3 Installation Precautions Adherence to the following will aid in problem-free installation with long-term reliability: WARNING - Several different sources of power can be con- Like all solid state electronic devices, this system may operate nected to the fire alarm control panel. Disconnect all sources of erratically or can be damaged when subjected to lightning induced power before servicing.
  • Page 4 Software Downloads In order to supply the latest features and functionality in fire alarm and life safety technology to our customers, we make frequent upgrades to the embedded software in our products. To ensure that you are installing and programming the latest features, we strongly recommend that you download the most current version of software for each product prior to commissioning any system.

  • Page 5: Table Of Contents

    Table of Contents Section 1: Introduction ..............................8 1.1: Basic System Overview.....................................8 1.1.1: Hardware Features ....................................8 1.1.2: Software Features ....................................8 1.2: About this Manual......................................8 1.2.1: Terms Used in this Manual..................................8 1.3: Compatible Products......................................9 1.4: Related Documentation .....................................9 Section 2: Agency Listings, Approvals, and Requirements..................10 2.1: Federal Communications Commission (FCC)..............................10 2.1.1: Electrical Safety Advisory..................................10 2.2: Underwriters Laboratories (UL) ..................................11...
  • Page 6 Table of Contents 4.14: Onboard Relays (Conventional) ..................................34 4.14.1: Common Trouble Relay ..................................34 4.14.2: Programmable Relays ..................................34 4.15: Remote Station Applications ..................................34 4.15.1: Keltron Model 3158 Installation.................................34 4.15.2: City Box Connection Using the 5220 Module ...........................35 4.15.3: NFPA 72 Polarity Reversal ................................36 4.15.4: Using a MR-201/T Control Relay From Air Products ........................37 4.15.5: Transmitter Activated by Dry Contacts ..............................38 Section 5: Programming Overview ..........................
  • Page 7 Table of Contents 7.2: Menu System ........................................67 7.2.1: Panel Login Menu....................................67 7.2.2: Main Menu Overview...................................69 7.2.3: Using the Menus ....................................69 7.3: Basic Operation .......................................69 7.3.1: Setting Time and Date ..................................69 7.3.2: Disable / Enable a Point..................................69 7.3.3: View Event History ....................................70 7.3.4: Conduct a Fire Drill ....................................70 7.3.5: Conduct an Indicator Test..................................70 7.3.6: Conduct a Walk Test ....................................70...

  • Page 8: Section 1: Introduction

    Section 1: Introduction The GWF-7075 and GWF-7075BFire Alarm Control / Communicators are Addressable Fire Alarm Control Systems that meets the require- ments of UL 864 10th Edition Standard. NOTE: All references to GWF-7075 within this manual are applicable to the GWF-7075 and GWF-7075B. 1.1 Basic System Overview 1.1.1 Hardware Features •...

  • Page 9: Compatible Products

    Compatible Products Introduction 1.3 Compatible Products The chart below lists the products available for use with the GWF-7075. Type of Device Model Description Velociti Addressable SLC For a list of compatible devices, refer to the Compatibility Addendum, P/N 9000-0427-L8. Devices SWIFT Wireless SLC Devices For a list of compatible devices, refer to the SWIFT Manual, P/N: LS10036-000GF-E.

  • Page 10: Section 2: Agency Listings, Approvals, And Requirements

    Section 2: Agency Listings, Approvals, and Requirements Install and maintain this panel in accordance with NFPA 72. Detector spacing shall be done in accordance to NFPA 72. End-of -line relays and resistors shall be placed within the electrical box located at the end of the initiating circuit. Testing and maintenance should be performed in compliance with NFPA 72.

  • Page 11: Underwriters Laboratories (Ul)

    Underwriters Laboratories (UL) Agency Listings, Approvals, and Requirements CAUTION: INSTALLATION AND TEST TO ENSURE PROPER OPERATION, THIS EQUIPMENT MUST BE INSTALLED ACCORDING TO THE ENCLOSED INSTALLATION INSTRUCTIONS. TO VERIFY THAT THE EQUIPMENT IS OPERATING PROPERLY AND CAN SUCCESSFULLY REPORT AN ALARM, THIS EQUIPMENT MUST BE TESTED IMMEDIATELY AFTER INSTALLATION, AND PERIODICALLY THEREAFTER, ACCORDING TO THE ENCLOSED TEST INSTRUCTIONS.

  • Page 12: 6: Requirements For The Installation Of Carbon Monoxide (Co) Detection And Warning Equipment, Nfpa 72

    Agency Listings, Approvals, and Requirements Underwriters Laboratories (UL) 2.2.6 Requirements for the Installation of Carbon Monoxide (CO) Detection and Warning Equipment, NFPA 72 When using carbon monoxide detection the system must be monitored by a Supervising Station with emergency response, both aspects meet- ing the Standard for the Installation of Carbon Monoxide (CO) Detection and Warning Equipment, NFPA 72.

  • Page 13: Section 3: Prerequisites For Installation

    Section 3: Prerequisites for Installation This section of the Manual is intended to help you plan your tasks to facilitate a smooth installation. Please read this section thoroughly, especially if you are installing a GWF-7075 panel for the first time. 3.1 Inventory When the GWF-7075 shipment is received, check that all the parts have been included in the shipment.

  • Page 14: Calculating Current Draw And Standby Battery

    Prerequisites for Installation Calculating Current Draw and Standby Battery Label Rating Terminal No. Description Group Individual Voltage Current Terminal Block 2 SBUS – SBUS Power 27.4 VDC 0.5 A SBUS Communication 5 VDC 100 mA NAC1 – Notification Appliance Circuit/Auxiliary power 27.4 VDC 1 Amp NAC or Aux power NAC2...
  • Page 15 Calculating Current Draw and Standby Battery Prerequisites for Installation Standby Device # of Devices Current per Device Alarm Current Current ASD-PL3/-IV ASD-PTL3/-IV ASD-PL3R/-IV ATD-L3/-IV Standby: 0.2 mA Alarm: 4.5 mA ATD-L3H/-IV ATD-L3R/-IV MCS-COF MCS-CO3 ABD-2F (without integral test) Standby/Alarm: 2 mA Aux.
  • Page 16 Prerequisites for Installation Calculating Current Draw and Standby Battery Standby Device # of Devices Current per Device Alarm Current Current MMI-6SF Aux Pwr Standby 50 mA Alarm: 70 mA Standby 2.3 mA Alarm: 40 mA SLC Accessories B200S/-W/-IV Intelligent Sounder Aux Pwr Standby: 0.5 mA...
  • Page 17 Calculating Current Draw and Standby Battery Prerequisites for Installation Standby Device # of Devices Current per Device Alarm Current Current Multiply lines E and F. Total standby AH Alarm sounding period in hours. (For example, 5 minutes = 0.0833 hours) Multiply lines E and H.

  • Page 18: Section 4: Control Panel Installation

    Section 4: Control Panel Installation CAUTION: DISCONNECT POWER TO AVOID THE RISK OF ELECTRICAL SHOCK AND DAMAGE TO THE UNIT, POWER SHOULD BE OFF AT THE CONTROL PANEL WHILE INSTALLING OR SERVICING. 4.1 Mounting the Control Panel Cabinet Read the Environmental Specifications in Section 3.2 before mounting the GWF-7075 panel. The GWF-7075 cabinet base dimensions are: 12.531”...
  • Page 19 Mounting the Control Panel Cabinet Control Panel Installation Close the dead front panel. The bottom two screws on the annunciator will protrude through the dead front panel. Reinstall the top two annunciator screws removed in step 1. Insert the two screws with the star washers into the bottom of the cabinet to secure the dead front to the cabinet. remove top two annunciator screws from board and secure through dead front panel bottom two screws protrude...

  • Page 20: Board Assembly Diagram

    Control Panel Installation Board Assembly Diagram 4.2 Board Assembly Diagram The drawing below shows the location of components for FACP wiring. onboard annunciator DIP switch Power Input: 120VAC, 60Hz, 1.5A Ethernet Cellular connection battery connection phone line Form C SBUS NACs/ connection Trouble Relays...

  • Page 21: Ac Power Connection

    AC Power Connection Control Panel Installation AC input NAC circuits Phone lines Note: 0.25” spacing must be maintained between each of these circuit types; as well as between power-limited and non-power-limited circuits. Battery connection SBUS Relays Battery Battery Figure 4.4 Wire Routing Example 4.4 AC Power Connection At installation, connect the AC terminals to the power source as shown in Figure 4.5.

  • Page 22: Battery Power

    Control Panel Installation Battery Power 4.5 Battery Power The batteries must be sealed lead acid type. Before connecting the batteries to the FACP, make certain that the interconnect cable between the batteries is not connected. Do not connect the battery jumper cable until the system is completely installed. Observe polarity when connect- ing the batteries.
  • Page 23 Wiring Specifications Control Panel Installation To calculate the wire gauge that must be used to connect SBUS modules to the panel, it is necessary to calculate the total worst case current draw for all modules on a single 4-conductor bus. The total worst case current draw is calculated by adding the individual worst case currents for each module.

  • Page 24: 3: Wiring Configurations

    Control Panel Installation Wiring Specifications The total worst case current is calculated as follows: Current Draw = 2 x 0.100 amps = 0.200 amps GFPS-6S Current Draw = 1 x 0.010 amps = 0.010 amps 5824 Current Draw = 1 x 0.045 amps = 0.045 amps Total Worst Case Current Draw = 0.255 amps...

  • Page 25: Ra-1000/R Remote Annunciator Installation

    RA-1000/R Remote Annunciator Installation Control Panel Installation 4.7 RA-1000/R Remote Annunciator Installation The RA-1000/R is an optional remote annunciator. Up to 8 annunciators can be added to the GWF-7075 system. FIRE ALARM ANNUNCIATOR Figure 4.9 RA-1000/R Remote Annunciator RA-1000/R installation involves the following steps: Ensure the power is off at the panel.
  • Page 26 Control Panel Installation RA-1000/R Remote Annunciator Installation The RA-1000/R comes from the factory fully assembled. You must disassemble it for mounting. To disassemble the annunciator, use a 5/64 hex wrench to remove the set screws, located on the bottom of the annunciator bezel. (See Figure 4.11 for location of the set screws.) screws for placement of mounting wires surface mounting holes...

  • Page 27: 5824 Serial/Parallel Printer Interface Module Installation

    .5824 Serial/Parallel Printer Interface Module Installation Control Panel Installation Wire the annunciator to the FACP as shown below. supervised, power-limited, Class B Figure 4.13 RA-1000/R Connection to the Panel Replace the electronic assembly in the backbox. Place the bezel over the backbox and tighten the set screws on the bezel. Refer to Figure 4.11 for location of set screws.

  • Page 28: 5880 Led Driver Module

    Control Panel Installation 5880 LED Driver Module Press ENTER to bypass the next two screens. A screen similar to the one shown below will display. Select Yes if printer should be supervised for Monitor Printer=Yes Out-of-Paper and Offline conditions. Output Port=Parallel Select type of printer, Parallel or Serial.

  • Page 29: 2: Facp Connection

    5880 LED Driver Module Control Panel Installation 4.9.2 FACP Connection The 5880 connects to the panel via the SBUS. Make connections as shown below. After the 5880 is connected to the panel, it must be added to the system. Programming is described in Section 6. 5880 SLC OUT SLC PROG NAC 1...

  • Page 30: 4: Dry Contact Wiring

    Control Panel Installation Configuring Modules Pin # LED1 LED2 LED3 LED4 LED5 LED6 LED7 LED8 Cathode LED9 LEDs LED10 LED Power Anode no connection Pin # LED11 LED12 LED13 LED14 LED15 LED16 LED17 LED18 Cathode LED19 P3 and P4 are wired LEDs LED20 the same as P2.

  • Page 31: 1: Assigning Module Ids

    Configuring Modules Control Panel Installation 4.10.1 Assigning Module IDs When installing a hardware module (see Table 4.5 for list of compatible SBUS devices), you must use the DIP switches on the module to assign an ID# to the module. Figure 4.20 shows all possible DIP switch positions and their correlation to a numerical ID. Address 0 is an invalid address and cannot be used.

  • Page 32: Telephone Connection

    Control Panel Installation Telephone Connection 4.11 Telephone Connection Connect the telephone lines as shown in Figure 4.21. Model 7860 phone cord is available from Honeywell for this purpose. A number of programmable options are available for customizing the telephone lines. These options are described in Section 6.6. RELAY 2 RELAY 1 TROUBLE...

  • Page 33: Class A Notification Wiring

    Class A Notification Wiring Control Panel Installation 4.13 Class A Notification Wiring You must use an appliance from the list of compatible appliances listed in the Device Compatibility Document, P/N: 9000-0427-L8. To install a Class A notification appliance circuit: Wire the Class A notification appliances as shown in Figure 4.23. CAUTION: SYSTEM SUPERVISION FOR PROPER SYSTEM SUPERVISION DO NOT USE LOOPED WIRE UNDER TERMINALS MARKED –...

  • Page 34: Onboard Relays (Conventional)

    Control Panel Installation Onboard Relays (Conventional) Constant Power Use constant power for applications that require a constant auxiliary power source. Power is always present at Constant circuits. Resettable Power Resettable power is typically used to power beam detectors, flame detectors and conventional 4-wire smoke detectors. For circuits selected as Resettable, 27.4 volt power is always present at the terminals unless a system reset occurs.

  • Page 35: 2: City Box Connection Using The 5220 Module

    Remote Station Applications Control Panel Installation This is intended for connection to a polarity reversal circuit of a remote station SLC IN SLC OUT SLC PROG NAC 1 RELAY 2 RELAY 1 TROUBLE SBUS NAC 2 receiving unit having compatible ratings. All circuits power-limited.

  • Page 36: 3: Nfpa 72 Polarity Reversal

    Control Panel Installation Remote Station Applications 4.15.3 NFPA 72 Polarity Reversal Using the 5220 Module When the 5220 is wired and programmed for polarity reversal, it reports alarm and trouble events to a remote site. Alarms will override trou- ble conditions and it will not be possible to reset the remote indicator until the condition is cleared and the control panel is reset. If an alarm condition occurs, the alarm relay will close, overriding the trouble condition.

  • Page 37: 4: Using A Mr-201/T Control Relay From Air Products

    Remote Station Applications Control Panel Installation Using the 7644-L8 Module When the 7644-L8 is used for polarity reversal, it allows alarm and trouble events to be reported to a remote site. Alarms will override trou- ble conditions and it will not be possible to reset the remote indicator until the condition is cleared and the control panel is reset. To install the 7644-L8 for polarity reversal: Wire the 7644-L8 to the control panel as shown in Figure 4.29.

  • Page 38: 5: Transmitter Activated By Dry Contacts

    Control Panel Installation Remote Station Applications Program the NAC circuit as a non silence NAC circuit (see Section 6.5.2). NOTE: If you need to transmit supervisory or trouble conditions, additional relay modules must be added. Use relay 1 to transmit supervisory conditions.

  • Page 39: Section 5: Programming Overview

    Section 5: Programming Overview This section of the manual is intended to give you an overview of the programming process. Please read this section of the manual carefully, especially if you are programming the control panel for the first time. The JumpStart auto-programming feature automates many programming tasks and selects the default options for the system.

  • Page 40: 3: Running Jumpstart Auto-Programming

    Programming Overview Mapping Overview Configured as Notification and assigned to Group 1. JumpStart auto-programming automatically programs Zone 1 to activate Circuits 1-2 Group 1 using constant on output when an alarm condition occurs. Assigned to Group 124. JumpStart auto-programming automatically programs Zone 1 to activate Group 124 using con- Circuit 3 (Relay 1) stant on output when a supervisory condition occurs.

  • Page 41: 1: Input Point Mapping

    Mapping Overview Programming Overview Figure 5.1 is a brief overview of the concept of mapping. The next several pages of the manual show these subjects in detail. In its simplest application, mapping determines which outputs are activated by which inputs. input zone output group input points...

  • Page 42: 3: Event Mapping

    Programming Overview Mapping Overview 5.3.3 Event Mapping There are 11 types of zone events, 14 types of panel events, and 6 types of site events that can be mapped (see Table 5.2). For each event type, you can activate the output groups with specific the output patterns. Mapping examples are shown in Figures 5.4, 5.5, & 5.6. System Zone Panel...

  • Page 43: 4: Mapping Led Points

    Programming Using the HFSS Software Suite Programming Overview Group 3 Group 3 Zone 3 Zone 3 3rd floor 3rd floor Offices Offices notification notification 3rd floor 3rd floor ANSI 3.41 Group 2 Zone 2 Group 2 Zone 2 manual pull 2nd floor Storage 2nd floor...

  • Page 44: 1: Entering / Exiting The Program Menu

    Programming Overview Programming Menu Quick Reference The following subsections describe the programming basics, including a description of editing keys available for programming and how to move through the programming menus. Section 6 contains specific information about the individual programming options. NOTE: Mapping cannot be programmed through the on-board and remote annunciators.
  • Page 45 Programming Menu Quick Reference Programming Overview Menu Options/Defaults Reference 5824 Printer Module RA-1000/R LCD Annunciator 5880 LED I/O Module Delete Module Select Module Section 6.2.3 View Module List Select Module Section 6.2.4 Edit Zone Name Section 6.3.1 *1-Count 2-Count Alarm Ver. Verification Type Add Module Section 6.2.2...
  • Page 46 Programming Overview Programming Menu Quick Reference Menu Options/Defaults Reference STATUS POINT CO DETECTOR SWITCH LATCH 1, 2 SWITCH SUPERVISORY DETECTOR NON-LATCH SWITCH OUTPUT PT Select Group AUX CONST 1, 2 NOTIF AUX RESET Select Module AUX DOOR Section 6.5.1 OUTPUT PT Select Group 1, 2 RELAY...
  • Page 47 Programming Menu Quick Reference Programming Overview Menu Options/Defaults Reference No Accessory base SDR BAS Single station or Multi station RLY BAS Silence or Non- Silence Latch or non- ACCLIMATE latch, Single I-SdrBa station or Multi (Intelligent station, Silence Sounder Base) or Non-Silence, volume high (default) or low...
  • Page 48 Programming Overview Programming Menu Quick Reference Menu Options/Defaults Reference No Accessory base SDR BAS Single station or Multi station RLY BAS Silence or Non- Silence CO ALARM/ Latch or non- FIRE ALARM latch, Single I-SdrBa station or Multi (Intelligent station, Silence Sounder Base) or Non-Silence, volume high...
  • Page 49 Programming Menu Quick Reference Programming Overview Menu Options/Defaults Reference UNUSED Point NOTIF OUTPUT 5880 Enter Point # Section 6.5.3 Select Group (cont.) NOTIF CONTROL Edit Name CIRCUIT Set the Hour Set the Minutes *02:00AM Auto Time Test Select AM/PM Enter Interval 24 hrs,12 hrs, *6 hrs, 4 hrs For each phone line (1 &...
  • Page 50 Programming Overview Programming Menu Quick Reference Menu Options/Defaults Reference 75 sec, 90 Sec, 3 Ethernet Supervise min, 5 min, 1 hr, 24 *5 Minutes hrs, 30 days, None 24Hrs, 30 days, Cellular Supervise *24 Hours AlarmNet Timers none 10 min, 15 min, 30 Minutes, 1 hr, 2 hrs, Old Alarm Time *30 Minutes...
  • Page 51 Notes GWF-7075 Manual — LS10147-002GF-E:G 10/5/2022...

  • Page 52: Section 6: Programming

    Section 6: Programming This section of the manual describes how to manually program the control panel from the built-in annunciator. Each subsection describes these menu options. All options described in this section can be performed using the HFSS Honeywell Fire Software Suite. NOTE: JumpStart auto-programming should be run Before any customized programming is performed.

  • Page 53: 2: Adding Modules

    Zone Programming 5880-LED I/O Default name for 5880 module Module ID: 03 (no customization) 5880 03_________ <Module Name> 5880-LED I/O Use arrow keys to select characters. Letters begin displaying with “A”. Press AB_____________ the ENTER key to select the desired character.
  • Page 54 Programming Zone Press 2 to enter the Zone Menu. Press 1 to edit a zone. Enter the Zone Number, then press ENTER. Edit Zone Name To edit the Zone Name, press 1. You can enter a description to display a descriptive name for the a zone. NOTE: See Appendix A for information to edit names.
  • Page 55 Zone Programming The MCS-COF and other CO detectors can only be installed in a 1 count zone. They will operate as a 1- count point regardless of the programmed zone type (i.e. Alarm Verification, 2 count, etc.). PAS operation requires the approval of the local Authority Having Jurisdiction. Alarm Verification, two-count, single interlock releasing, and double interlock releasing cannot be used while PAS is enabled.

  • Page 56: 2: View Zone Points

    Programming Group 6.3.2 View Zone Points To view the points in a zone, follow these steps: Login to the panel. The panel will automatically access the main menu. Select 7 to access the panel programming. Press 2 to enter the zone menu. Press 2 to view the zone points.

  • Page 57: 3: Edit Output Group Template

    Point Programming Enter the group number, then press ENTER.. Group: G91 of 8 Point: 98:001 Number: 1 of 8 Figure 6.5 View Group Points 6.4.3 Edit Output Group Template Login to the panel. The panel will automatically access the Main Menu. Select 7 to access the Panel Programming.
  • Page 58 Programming Point Type Latching Function Comments Selection Option SUP PHOTO DUCT Latching Supervisory switches can be latching or non-latching. DETECTOR Non Latching SUP SMOKE PHOTO SUP SMOKE ION SUP HEAT SUP ACCLIMATE SUP HEAT HT SUP SMOKE PHOTO/HEAT SUP SMOKE BEAM CO SMOKE ALRM CO/ALRM DETECTOR...

  • Page 59: 2: Point Programming For The Internal Or External Power Module

    Point Programming Type Latching Function Comments Selection Option ZN_AUX1 Latching Use these switch types if you want to monitor special zone-level conditions. Non Latching ZN_AUX2 Latching Non Latching SYS_AUX1 Latching Use these switch types if you want to monitor special system-wide conditions. Non Latching SYS_AUX2 Latching...

  • Page 60: 3: Point Programming For 5880

    Programming System Options Function Selections Choices Type Selections Comments for each Type Enter Point or Circuit Select Type UNUSED NOTIF OUT CTRL CKT AUX PWR CONSTANT Constant auxiliary power. RESETTABLE Resettable auxiliary power. DOOR Door holder auxiliary power. AUX SYNC Sounder Sync auxiliary power for System Sensor Select Group Group or Zone selection will appear depending on the type selected...

  • Page 61: 1: Communication Options

    System Options Programming 6.6.1 Communication Options Auto Test Time To access the Auto Test Time screen: Login to the panel. Select 7 to access the Program Menu. Select 5 to access System Options. From the next Menu, select 1 to access Communication Options. Select 1 to access Auto Test Time.
  • Page 62 Programming System Options  Dial Option (Touch-tone or Pulse) Press the up or down arrow keys to select the Dial Option, then press ENTER. Dial Option Description PULSE If this option is selected, only pulse dialing will be used for this phone line. Touch-tone dialing.

  • Page 63: 2: Daytime/Nighttime Sensitivity

    System Options Programming • Ethernet: 5 minutes (default), 3 minutes, 90 seconds, 75 seconds, none, 30 days, 24 hours, 1 hour. • Cellular: 24 hours (default), none, 30 days • Old Alarm: 30 minutes (default), 15 minutes, 10 minutes, none, 24 hours,12 hours, 6 hours, 4 hours,2 hours, 1 hour Ethernet: 5 Minutes_ Cellular: 24 Hours_ Old Alarm: 30 Minutes_...

  • Page 64: 4: Time Options

    Programming System Options Select the holiday schedules you want to edit (1- holidays 1 - 9, 2- holidays 10 - 18). Enter Holidays 1-9 01/01 07/04 12/24 pre-programmed holidays 12/25 --/-- --/-- programmable holiday locations --/-- --/-- --/-- Figure 6.13 Edit Holidays Screen Enter the month of the holiday, then press ENTER.

  • Page 65: 5: Miscellaneous Options

    System Options Programming Enter the number of hours before a low AC report will be sent to the central station, then press ENTER. Clock Display Format (AM/PM or Military) To change the system clock display format, continue programming from step 8 above: Select AMPM (for AM/PM display format) or MIL (for military or 24 hr display format) by pressing the up or down arrow, then press ENTER.

  • Page 66: 7: Edit Banner

    Programming JumpStart Auto-Programming Then, press ENTER two times to make your selection and exit. 6.6.7 Edit Banner The banner is the message that displays on the panel LCD when the system is normal. For example, a system is normal when no alarms or troubles exist and no one is currently using the system menus.

  • Page 67: Section 7: System Operation

    Section 7: System Operation The operation of the control panel is simple. Menus guide you step-by-step through operations. This section of the manual is an overview of the Operation Menus. Please read this entire section carefully before operating the panel. After logging in to the panel, press ENTER to view the main menu.
  • Page 68 System Operation Menu System Admin Profiles After initial power-up, the GWF-7075 requires a password change and user account setup before programming. Only Admin1 will be active. Using the login for Admin1, the default password (0000000) must be changed to a new, unique password. This new password must be 7-dig- its and cannot be sequential or easily guessed.

  • Page 69: 2: Main Menu Overview

    Basic Operation System Operation 7.2.2 Main Menu Overview Table 7.2 lists a brief overview of the main menu after you have logged in to the panel. These options are described in greater detail through- out this section of the manual. Main Menu Options Description 1- System Tests...

  • Page 70: 3: View Event History

    System Operation Basic Operation 7.3.3 View Event History Use the View Event History feature to display events on LCD. From the main menu, press 3 to select the Event History. Events will begin displaying with the most recent events appearing first. The panel can store up to 1000 events.

  • Page 71: 7: Conduct A Communicator Test

    Basic Operation System Operation If you do not end the Walk Test manually within four hours, it will end automatically. If there is an alarm or pre-alarm condition in the sys- tem, you will not be able to enter the Walk Test. NOTE: The panel does not do a full 30 second reset on resettable power outputs.

  • Page 72: 12: View Status Of A Point

    System Operation Basic Operation Example of detector not in compliance Example of detector in compliance blanks indicate percent obscurity SMOKE PHOTO 2.5% SMOKE PHOTO ---% detector not in per foot compliance detector ID MODULE_33 POINT_4 MODULE_33 POINT_4 [Z001] [M33:004] A058 [Z001] [M33:004] A058 current value detector state...

  • Page 73: Operation Mode Behavior

    Operation Mode Behavior System Operation Feature Activation This Menu is used to activate/register additional features. Press 4 from the System Information menu. This will display the Feature Activation menu. Press 1 to enter a six-digit activation code or press 2 to review features already activated in this panel. Ethernet Info Screen From the System Information menu, press 5 to access the Ethernet Information.
  • Page 74 System Operation Panel Operating Modes • Trouble • Silenced • Reset Table 7.4 describes the behavior of the panel in each of these modes. Operating Occurs When System Behavior In This Mode You Can Mode Normal No alarm, supervisories SYSTEM POWER LED is on. The All Systems Normal Enter the appropriate code or rotate the key to or trouble condition exists display indicates that the system is in normal mode.
  • Page 75 Panel Operating Modes System Operation Operating Occurs When System Behavior In This Mode You Can Mode Supervisory The communicator seizes control of the phone line and Press the down arrow key to view the supervisory calls the central station. condition. A screen similar to this one displays. The onboard annunciator sounds a loud, pulsing beep in device SUPERVSY: MAN_PULL...

  • Page 76: 1: Multi-Site Annunciator And Multi-Site User Access

    System Operation Releasing Operations Operating Occurs When System Behavior In This Mode You Can Mode Reset The RESET button is All LEDs are on briefly then the LCD displays “ALARM Menus are not available during the reset process. pressed followed by a RESET IN PROGRESS”.

  • Page 77: 1: Single Interlock Zone Releasing

    Releasing Operations System Operation + – Either NAC circuit can be used. UL-listed solenoid supervisory module- must be located at the solenoid. black releasing solenoid Use 1 solenoid per circuit. Figure 7.6 Wiring Configuration for Solenoid NOTE: For releasing operations, a manual releasing disconnect switch is required per UL 864. Refer to the MRD-1 Series Document for installation instructions.

  • Page 78: Smoke Alarm Verification

    System Operation Smoke Alarm Verification Conditions Required for a Release Output Activation Any release requires the activation of an interlock switch, and either a manual release switch or two activated addressable detectors. When these conditions are met, the “Release” and “General Alarm” outputs will activate, and the “Alert” output will deactivate. Inputs Output Results 1st Addressable Detector...

  • Page 79: 4: Using A Recorded F-Key Macro

    Function Keys System Operation 7.8.4 Using a Recorded F-Key Macro From the Idle screen on any annunciator in the site, press the F-Key you want to activate. Once finished, deactivate the macro by pressing the F-Key again. 7.8.5 F-Key Status Event When an F-Key is enabled, it activates its corresponding F-Key Active Event.

  • Page 80: Section 8: Reporting

    Section 8: Reporting This section lists the receivers that are compatible with this control panel and the reporting codes sent by the control panel for SIA and Con- tact ID formats. 8.1 Receivers Compatible with the Control Panel Table 8.1 shows receivers compatible with the control panel. Manufacturer Model Format...
  • Page 81 Receivers Compatible with the Control Panel Reporting SIA Reporting Format Contact ID Reporting Format SIA pi Modifier Event Description Module ID Parameter Fixed Length Qualifier Event Group # Contact # # (If Any) Event Format NN - panel Code Codes XX- SBUS ID ZZZ- Zone # PPPP- Point #...
  • Page 82 Reporting Receivers Compatible with the Control Panel SIA Reporting Format Contact ID Reporting Format SIA pi Modifier Event Description Module ID Parameter Fixed Length Qualifier Event Group # Contact # # (If Any) Event Format NN - panel Code Codes XX- SBUS ID ZZZ- Zone # PPPP- Point #...
  • Page 83 Receivers Compatible with the Control Panel Reporting SIA Reporting Format Contact ID Reporting Format SIA pi Modifier Event Description Module ID Parameter Fixed Length Qualifier Event Group # Contact # # (If Any) Event Format NN - panel Code Codes XX- SBUS ID ZZZ- Zone # PPPP- Point #...
  • Page 84 Reporting Receivers Compatible with the Control Panel SIA Reporting Format Contact ID Reporting Format SIA pi Modifier Event Description Module ID Parameter Fixed Length Qualifier Event Group # Contact # # (If Any) Event Format NN - panel Code Codes XX- SBUS ID ZZZ- Zone # PPPP- Point #...
  • Page 85 Receivers Compatible with the Control Panel Reporting SIA Reporting Format Contact ID Reporting Format SIA pi Modifier Event Description Module ID Parameter Fixed Length Qualifier Event Group # Contact # # (If Any) Event Format NN - panel Code Codes XX- SBUS ID ZZZ- Zone # PPPP- Point #...
  • Page 86 Reporting Receivers Compatible with the Control Panel SIA Reporting Format Contact ID Reporting Format SIA pi Modifier Event Description Module ID Parameter Fixed Length Qualifier Event Group # Contact # # (If Any) Event Format NN - panel Code Codes XX- SBUS ID ZZZ- Zone # PPPP- Point #...

  • Page 87: Sia / Gwf-7075 Panels Pi Modifier Reporting

    SIA / GWF-7075 Panels PI Modifier Reporting Reporting 8.2 SIA / GWF-7075 Panels PI Modifier Reporting Events are sent to the Central Station as a variable length string: The Event Format is: EEZZZZ Where the Event Format is defined as follows: Code Event Code Description Event Code (2 characters)

  • Page 88: Sia- Gwf-7075 Panel Communicator

    Reporting SIA– GWF-7075 Panel Communicator 8.3 SIA– GWF-7075 Panel Communicator (Differences/additional features are underlined). Events are sent to the Central Station Receiver as a fixed length string. The event format is: EEPPMMZZZZ where the event format is defined as follows: Code Event Code Description Event code (2 characters)

  • Page 89: Section 9: Testing And Troubleshooting

    Section 9: Testing and Troubleshooting 9.1 Troubleshooting This section of the manual offers suggestions for troubleshooting hardware problems. Please read this section if you encounter a problem when you install the fire alarm control panel. If these suggestions do not solve your problem or if you encounter a problem that is not listed, contact Gamewell-FCI technical support for assistance.

  • Page 90: Built-In Troubleshooting And Testing Tools

    Testing and Troubleshooting Built-in Troubleshooting and Testing Tools 9.3 Built-in Troubleshooting and Testing Tools The FACP has several built-in testing and troubleshooting tools that can be used to save time while testing and troubleshooting points and SLC devices. 9.3.1 SLC Device Locater The SLC device locater can be used to locate a device on a SLC loop.

  • Page 91: Earth Fault Resistance

    Earth Fault Resistance Testing and Troubleshooting Press ENTER to generate an alarm for an input point or activate an output point. To exit, press the left arrow key. 9.4 Earth Fault Resistance Table 9.2 lists the Earth Fault Resistance Detection for each applicable terminal on the FACP. TERMINAL LOW BIASED HIGH BIASED...

  • Page 92: Section 10: Installation Records

    Section 10: Installation Records Use this section of the manual as a reference list to track how points, zones, and groups are programmed. 10.1 SLC Device Point Record You can use Table 10.1 and to keep track of Velociti SLC detectors and modules. Default addresses for ID: Onboard: = 97 Zone / Detector Addr...

  • Page 93: Appendix A: Editing Text Using The Built-In Programmer

    Appendix A: Editing Text Using the Built-In Programmer This section contains the tables of programmable characters that may be used for the device, module, site, template, group, and zone names. T9 style editing is used. A.1 Characters Used for Editing Text Table A.1 lists the available characters and their associated numeric designator.

  • Page 94: Appendix B: Expanded Receiver/Panel Relationship

    Appendix B: Expanded Receiver/Panel Relationship The available Receiver Number will correspond with the panel number you entered. The Receiver Numbers are populated based on the panel number and they are audited to allow only the four appropriate receivers. See Section 6.2.6. Panel Available Receiver Numbers Table B.1 Receiver/Panel Relationship...

  • Page 95: Appendix C: Cadence Patterns

    Appendix C: Cadence Patterns Table C.1 shows the cadence patterns available for use with the control panel. Name Pattern Description (Patterns repeat until condition is cleared.) Constant Continuous sound (This is the only pattern that can be used for relay circuits. The system will override any other choice.) March Time 0.5 second on, 0.5 second off...

  • Page 96: Appendix D: Panel Security

    Appendix D: Panel Security Panel Installation / Maintenance Security Checklist System Description: ________________________________________________________________ System Location: __________________________________________________________________ Installer: _________________________________________________ Date: ___________________ Complete the following Cybersecurity Tasks for Each Panel Installation • Install the panel in a secure location considering both software and hardware vulnerabilities. •...

  • Page 97: Model Gwf-7075 Basic Operating Instructions

    Model GWF-7075 Basic Operating Instructions These instructions must be framed and displayed next to the GWF-7075 panel in accordance with NFPA 72 fire code for Local Protected Fire Alarm Systems. Test the system in accordance to NFPA 72. Operation Task to Perform Silence Alarms and Troubles Press SILENCE and then enter a code if prompted.
  • Page 99 Manufacturer Warranties and Limitation of Liability Manufacturer Warranties. Subject to the limitations set forth herein, Manufacturer warrants that the Products manufactured by it in its Northford, Connecticut facility and sold by it to its authorized Distributors shall be free, under normal use and service, from defects in material and workmanship for a period of thirty six months (36) months from the date of manufacture (effective Jan.
  • Page 100 Honeywell Gamewell-FCI 12 Clintonville Road Northford, CT 06472-1610 203.484.7161 LS10147-002GF-E | G | mm-yy www.gamewell-fci.com ©2022 Honeywell International Inc.

Table of Contents