Vitek VT-1796 VT - Massage Foot Spa Manual

FOOT SPA

Foot SPA will bring relief to tired legs and increase blood circulation in legs significantly. Air bubbles provide muscle relaxation. Infrared lamp enables heating of a particular part of your foot. Supplied massage accessories and surface of foot SPA suit perfectly for acupuncture massage.

DESCRIPTION

1. Operation mode switch
2. Splash guard
3. Air bubbles release openings
4. Surface for acupuncture massage
5. Mounting point of interchangeable attachments
6. Infrared lamp

Removable attachments

7. Roller attachments
8. Attachments for acupressure massage
9. Brush-attachment
10. Attachment for acupuncture massage
11. Pumice attachment

PRECAUTIONS

• The foot spa should not be used in cases of: benign and malignant tumors, skin inflammation or skin lesions, vein inflammation, varicose veins or thrombosis, open or fresh wounds, bruises, shin or joint pain, feet swelling, severe cases of diabetes.
• If you are pregnant, consult your doctor before using the unit.
• Stop the massage if you feel any discomfort.
• To avoid burns, people insensitive to heat should check the water temperature with a thermometer before filling the foot spa.
• Consult your doctor regarding any other questions you may have.

RECOMMENDED MASSAGE TIME

Usually the massage session should last not longer than 15-20 minutes. Make foot massage no more than once or twice a day. Determine comfortable massage time according to your sensations.

Let the unit cool down for at least 10 minutes before the next use.

BEFORE THE USE

After unit transportation or storage under cold (winter) conditions, it is necessary to keep it for at least two hours at room temperature before switching on.

• Unpack the unit completely and remove any stickers that can prevent unit operation.
• Check the unit for damages; do not use it in case of damages.
• Before switching the unit on, make sure that your home mains voltage corresponds to the unit operating voltage.

USAGE

Attention!
Do not plug or unplug the unit while your feet are in the water.

Attention!

• The foot SPA only keeps water warm, but does not heat it.
• Use the foot SPA only when sitting. It is strictly prohibited to stand up when your feet are in the foot SPA. The unit is not intended for carrying the body weight.
• Always install the attachments (7 or 8) as their absence does not allow to massage the whole feet surface.

Installation and assembling

• Make sure that the power plug is not inserted into the mains socket.
• Put the foot SPA on the floor away from heat and moisture sources and direct sunlight.
• Install the attachments for roller (7) or acupressure (8) massage into the notches on the surface for acupuncture massage (4).
• Install the desired attachment (9, 10 or 11) on the mounting point (5).
• Fill the foot SPA with warm or cool water to the maximal level mark «MAX».
• Insert the power plug into the mains socket.

Operation mode selection and massage

• Select an operation mode with the button (1):
  «I» (press once) – vibration and bubble massage + keep warm + infrared light.
• Sit on a chair and immerse your feet into the water.
• After the procedure take your feet out of the water.

Switching the unit off

• Consequently press the button (1) until the unit is switched off.
• Let the unit cool down and pour out the water.
• Rinse the inner surface of the foot SPA with water and a neutral detergent.

Cleaning and care

• Do not immerse the unit body, the power cord and the plug into water or other liquids.
• Do not use abrasives, hard brushes or solvents to clean the unit.
• Before pouring out the water, make sure that the unit is unplugged.
• Wipe the outer surface of the foot SPA with a soft cloth dampened in a neutral detergent solution and then wipe it dry.
• Rinse the inner surface of the foot SPA with water and a neutral detergent.

Storage

• Clean the foot SPA before taking it away for storage.
• Keep the foot SPA away from children in a dry cool place.

Delivery set

Foot SPA – 1pc.

Attachments for acupressure massage – 2 pc.

Roller attachments – 2 pcs.

Brush-attachment – 1 pc.

Attachment for acupuncture massage – 1 pc.

Pumice attachment – 1 pc. Instruction manual – 1 pc.

Technical specifications

Power supply: 230-240 V ~ 50 Hz

Heating power: 93 W

The manufacturer preserves the right to change the design and the specifications of the unit without a preliminary notification.

Unit operating life is 5 years