EWM M3.00 Operating Instructions Manual page 4

Contents
Notes on the use of these operating instructions
5.6.8
5.6.9
5.6.10
5.6.11
5.6.12
5.7 TIG welding .................................................................................................................................. 51
5.7.1
5.7.2
5.7.3
5.7.4
5.7.5
5.8 MMA welding ................................................................................................................................ 57
5.8.1
5.8.2
5.9 Shielding gas supply (shielding gas cylinder for welding machine) ............................................. 58
5.9.1
5.9.2
5.9.3
5.10 Remote control ............................................................................................................................. 59
5.11 Interfaces for automation ............................................................................................................. 59
5.11.1
6 Maintenance, care and disposal ......................................................................................................... 61
6.1 General......................................................................................................................................... 61
6.2 Maintenance work, intervals ........................................................................................................ 61
6.2.1
6.2.2
6.2.3
6.3 Maintenance work ........................................................................................................................ 62
6.4 Disposing of equipment ................................................................................................................ 63
6.4.1
6.5 Meeting the requirements of RoHS .............................................................................................. 63
7 Rectifying faults.................................................................................................................................... 64
7.1 Checklist for rectifying faults ........................................................................................................ 64
7.2 Error messages (power source) ................................................................................................... 65
7.3 Display machine control software version .................................................................................... 67
7.3.1
7.4 Vent coolant circuit ....................................................................................................................... 69
8 Technical data....................................................................................................................................... 70
8.1 Phoenix Expert drive 4 M3.00 ...................................................................................................... 70
9 Accessories .......................................................................................................................................... 71
9.1 General accessories .................................................................................................................... 71
9.2 Remote control/connecting and extension cable ......................................................................... 71
9.2.1
9.2.2
9.3 Options ......................................................................................................................................... 71
4
MIG/MAG functional sequences / operating modes ..................................................... 38
5.6.8.1 Explanation of signs and functions ................................................................ 38
MIG/MAG automatic cut-out ......................................................................................... 48
Standard MIG/MAG torch ............................................................................................. 49
MIG/MAG special-torches............................................................................................. 49
5.6.11.1 Program- and Up- / down operation .............................................................. 49
MIG/MAG Push/Pull welding torch ............................................................................... 50
5.6.12.1 Pin assignment .............................................................................................. 50
Welding torch connection ............................................................................................. 51
Welding task selection .................................................................................................. 52
TIG automatic cut-out ................................................................................................... 52
TIG arc ignition ............................................................................................................. 53
5.7.4.1 Liftarc ignition ................................................................................................ 53
Pulses, function sequences .......................................................................................... 53
5.7.5.1 Explanation of signs and functions ................................................................ 53
Welding task selection .................................................................................................. 57
5.8.1.1 Setting using the stick electrode diameter .................................................... 57
Arcforce......................................................................................................................... 57
Gas test ........................................................................................................................ 58
"Rinse hose package" function ..................................................................................... 58
Setting the shielding gas quantity ................................................................................. 58
Remote control connection socket, 19-pole ................................................................. 60
Daily maintenance tasks ............................................................................................... 61
6.2.1.1 Visual inspection ........................................................................................... 61
6.2.1.2 Functional test ............................................................................................... 61
Monthly maintenance tasks .......................................................................................... 62
6.2.2.1 Visual inspection ........................................................................................... 62
6.2.2.2 Functional test ............................................................................................... 62
Annual test (inspection and testing during operation) .................................................. 62
Manufacturer's declaration to the end user .................................................................. 63
Resetting JOBs to status on delivery (Reset ALL) ....................................................... 68
7-pole connection ......................................................................................................... 71
19-pole connection ....................................................................................................... 71
099-004801-EW501
29.04.2013