Advertisement
Setting by LED Program Card
Value
Item
Forward/
Forward/
RunningMode
brake/Rev
Brake
Battery Type
Lipo
Li-Fe
Battery Cut-Off
Low
Middle
Voltage
Initial Start
1%
5%
Force
Punch
Level1
Level2
PWM
2K
4K
OFF
10°
Timing
OFF
10°
Turbo Timing
CCW
CW
Motor rotation
Drag Brake
OFF
5%
Max Reverse
25%
50%
Force
Level1
Level2
Brake Punch
Brake PWM
600Hz
1K
Neutral Range
3%
6%
Brushless
Brushed
Motor Type
How to used the LED Program Card
to setup the ESC.
Refer to here
For example: Now set the Punch to Level4
1) Plug "BEC" cable to the program card.
2) Esc connect the battery and then turn it on.
Brushless
3) Press the "Select" button one by one until
(Sensored with Turbo)
the "Item" no. up to "5".
4) Press the " " button one by one until the
"Value" no. up to "4".
5) Press the "Enter" button and then, the card
will show " SE" and "nd", now; all data are
ready to send but not successful.
BEC Cable
6) Press the "Enter" button again, and then the
card will show "SU" and "CC", now the
programming are succeeful.
Brushless
(Sensored with Turbo)
All ORCA products are manufactured in accordance with the highest quality standards. ORCA guarantees this product to be free from defects in materials or workmanship for 60
days from the original date of purchase verified by sales receipt. This limited warranty does not cover damages resulting from abnormal wear, misuse or improper product
maintenance.
To avoid unnecessary service and mailing charges, always eliminate all other possibilities and check all components for malfunctions before sending in your unit for repair.
Products sent in for repair that operate perfectly will be charged a service fee.
When sending in the product, always pack carefully and include the original sales receipt, a description of the problem encountered, your return address and contact information.
Since we do not have control over the installation and use of this product, we cannot accept any liability for any damages resulting from the usage of this product. Therefore,
using this product is at your own risk, and the user accepts all resulting liability from installing and using the product.
Copyright@2023
Forward/
Rev
Nixx
High
Disabled
10%
15%
20%
25%
30%
Level3
Level4
Level5
8K
12K
16K
24K
These two-function work
20°
30°
40°
with a brushless motor
20°
30°
40°
50°
60°
10%
20%
40%
60%
80%
75%
100%
Level3
Level4
Level5
Level6
2K
4K
9%
12%
15%
Refer to here
Model:
Dual
System
Bec cable
Bec cable
" " " " button
control
Value No.
Model:
Dual
System
Press and hole 5 sec
Double-press the "Enter" button
back to default setting.
will succeed in your programming.
. All Rights Reserved.
Item
RunningMode
Battery Type
Battery Cut-Off
Voltage
Initial Start
35%
Force
Punch
PWM
Timing
only
Turbo Timing
Motor rotation
100%
Drag Brake
Max Reverse
Force
Brake Punch
Brake PWM
Neutral Range
Motor Type
How to used the button to setup the ESC without program card:
(Transmitter must be turn on during setup the esc without program card.)
1.Connect the power wires of the ESC to a fully charged battery set; making sure the polarity is correct.
2.Used the 1.5mm screw to press the set hole button before switch on the esc, switch on esc and then hold
the button contiue about 2 second to wait the LED light off and hear the motor long beep sound appear.
3.Set hole button only to let you choice the function mode, red LED will flash one time to eleven time represent
+
which function you want to set.
LED
LED
SET
(BEC cable)
4.Transimitter will let you change the participate of each function,
OFF
ON
full throttle once time will increase one participate e.g. (the blue LED will flash two time from one time).
LED
SET
Power Switch
full brake once time will decrease one participate e.g. (the blue LED will flash one time from two time).
5.When you finish setup you can switch off the esc directly, it can save automatically.
Used the 1.5mm screw to press the set hole button before switch on the esc, switch on the esc and then
hold the button contiue about 3 second to wait the LED light сhange to orange сolor and hear the motor long
beep sound and then keep continue press the set button until the LED change from orange color to
Setting without Program Card
Value
Blue light
Blue light
Blue light
Blue light
Flash one time Flash two times Flash three times Flash four times Flash five times Flash six times Flash seven times Flash eight times
Forward/
Forward/
Forward/
Red light flash
brake/Rev
Brake
Rev
one time
Red light flash
Lipo
Li-Fe
Nixx
two times
Red light flash
Low
Middle
High
Disabled
three times
Red light flash
1%
5%
10%
four times
Red light flash
Level1
Level2
Level3
Level4
five times
Red light flash
2K
4K
8K
Six times
Red light flash
OFF
10°
20°
Seven times
Red light flash
OFF
10°
20°
Eight times
Red light flash
CCW
CW
Nine times
Red light flash
OFF
5%
10%
Ten times
Red light flash
25%
50%
75%
Eleven times
Red light flash
Level1
Level2
Level3
Level4
Twelve times
Red light flash
600Hz
1K
2K
Thirteen times
Red light flash
3%
6%
9%
Fourteen times
Red light flash
Brushless
Brushed
fifteen times
Esc back to default setup:
red and blue led light fast flash.
Release the set button and switch off the esc.
Blue light
Blue light
Blue light
Blue light
15%
20%
25%
30%
35%
Level5
12K
16K
24K
These two-function work
30°
40°
with a brushless motor
only
30°
40°
50°
60°
20%
40%
60%
80%
100%
100%
Level5
Level6
4K
12%
15%
Advertisement
