Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for in.hub HUB-RT100
- Page 1 INSTRUCTION MANUAL Add-On Module HUB-RT100 & HUB-MRT100 Version 1.2 / 12.07.2023...
-
Page 2: Table Of Contents
Table of contents Legal notice ..........................3 General information ......................... 5 Scope of delivery ............................5 General instructions for use ........................5 Intended use ..............................5 Safety requirements ............................5 Disposal ................................5 Service & Support ............................6 Product information ........................ 7 Principle of operation ............................ -
Page 3: Legal Notice
Legal notice 1 Legal notice Warning concept This manual contains information that you must observe for your personal safety and to prevent damage to property. Warnings are presented in decreasing order of hazard level as follows: DANGER Indicates a direct hazard for humans. Irreversible injuries or death will result if not observed. - Page 4 If third-party products and components are used, they must be recommended or approved by in.hub. Proper storage, setting up, assembly, installation, commissioning, operation, and maintenance are essential for the correct and safe operation of the product.
-
Page 5: General Information
2 General information This operating manual contains all the information you need for commissioning and using the HUB-RT100 or the HUB-MRT100. It is intended both for installers and testers who commission the device themselves and for service and maintenance technicians who install extensions or perform fault analyses. -
Page 6: Service & Support
General information 2.6 Service & Support If you have any questions about specific use cases or about technical parameters, please contact us. Mail: service@inhub.de Phone: +49 371 5347 825 (Technical Sales Staff) These details will connect you with the appropriate contact. -
Page 7: Product Information
Principle of operation The HUB-RT100 or HUB-MRT100 is plugged into the USB interface of an in.hub gateway, e.g. the HUB-GM200. If SIINEOS is installed on the gateway, then you can synchronize the system time via the software interface. -
Page 8: Assembly And Commissioning
Observe the applicable safety and accident prevention regulations for specific areas of application, e.g. the Machinery Directive. 4.1 Plugging in the HUB-(M)RT100 and putting it into operation Plug the HUB-MRT100 or the HUB-RT100 into the USB1 or USB2 port of your in.hub gateway. -
Page 9: Changing The Battery
Assembly and commissioning 3. Click Set hardware real-time clocks to transfer the system clock time to the external real-time clock. 4. Leave the stick permanently plugged into the device, so that in case of power supply interruptions the gateway can always obtain the time from the HUB-(M)RT100 again. 4.3 Changing the battery Note that the operating time of the HUB-(M)RT100 depends individually on the ambient conditions. - Page 10 Assembly and commissioning 3. Push the battery out of the battery compartment with a blunt, narrow item and insert a new battery. The label on the battery points upwards. Fig. 4: Change battery 4. Put the board back into the housing and screw first the board with the 4 short screws and then the housing with the 2 long screws.
-
Page 11: Optional: Integrating Hub-(M)Rt100 Into Linux
OPTIONAL: Integrating HUB-(M)RT100 into Linux 5 OPTIONAL: Integrating HUB-(M)RT100 into Linux The two add-on modules HUB-MRT100 and HUB-RT100 are proprietary developments of in.hub, for which no standard drivers are available to use them out-of-the-box. In order for the stick to be recognized by your individually developed system software, you must perform the following steps: Integrate chip driver mcp2221. -
Page 12: Technical Data
Technical data 6 Technical data Data Value Connector type USB 2.0 Type A Transmission speed Max. 400 Kbit/s Operating voltage / 4,75 ~ 5,25 V | ~ 61 mA operating current when connected via USB Quiescent current with 500 nA battery operation Total battery charge 220 mAh... -
Page 13: Eu Declaration Of Conformity
EU Declaration of conformity 7 EU Declaration of conformity... - Page 14 EU Declaration of conformity...
- Page 15 EU Declaration of conformity...
- Page 16 EU Declaration of conformity...
- Page 17 EU Declaration of conformity...