Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Tanaka TCM 75EBP
Summary of Contents for Tanaka TCM 75EBP
- Page 1 Model TCM 75EAP∙TCM 75EBP Handling instructions Note: Before using this machine, carefully read through these HANDLING INSTRUCTIONS to ensure effi cient, safe operation. It is recommended that these INSTRUCTIONS be kept readily available as an important reference when using this machine.
-
Page 2: Meanings Of Symbols
Pay special attention to statements preceded by the following words: Fuel and oil mixture WARNING Indicates a strong possibility of severe personal injury or Carburetor adjustment - Idle speed loss of life if instructions are not followed. CAUTION Indicates a possibility of personal injury or equipment damage if instructions are not followed. - Page 3 WHAT IS WHAT? (Fig. 1) A: Stop switch: Device for allowing the engine to be started or stopped. B: Throttle lever: Device activated by the operatorʼs fi nger, for controlling the engine speed. C: Throttle lever lockout: Device that prevents the accidental operation of the throttle lever until manually released.
-
Page 4: Warnings And Safety Instructions
○ All items, other than the items listed in the operator’s/ WARNINGS AND SAFETY owner’s manual, should be performed by Tanaka dealer. INSTRUCTIONS (For example, if improper tools are used to remove the fl ywheel or if an improper tool is used to hold the fl ywheel... - Page 5 ○ Keep others away when making carburetor adjustments. ○ Use only genuine Tanaka replacement parts as recommended by the manufacturer. Fig. 2 CAUTION Do not disassemble the recoil starter. There is a possibility of personal injury with recoil spring.
-
Page 6: Specifications
Pay special attention about the abrasive wheel. There is a risk of bursting to using the abrasive wheel wetted. If situations occur which are not covered in this manual, take care and use common sense. Contact Tanaka dealer if you need assistance. SPECIFICATIONS Model... -
Page 7: Assembly Procedures
○ Select and mount the correct cut-off wheel for the type of ASSEMBLY PROCEDURES work to be carried out. Assembly of cut-off wheel Abrasive wheels Diamond wheels 1. Place the wheel (1) between the two fl anges (2), and Plastic —... - Page 8 2. Use the hex. wrench (4) to rotate the tensioner bolt (11) Wet cutting with water so that the position of the tension nut (12) matches with This machine can be set up for wet cutting which can the marking (13) on the arm cover (10). (Fig. 12, Fig. 13) suppress dust emission during cutting.
-
Page 9: Operating Procedures
○ Always use branded 89 octane unleaded gasoline. please touch the ground that is slightly damp. ○ Use genuine two-cycle oil or use a mix between 25:1 to 50:1, please consult about the oil mixture ratio to Tanaka Starting the cold engine (Fig. 22-27) dealer. -
Page 10: Basic Cutting Techniques
5. Push the decompression valve (26). The valve will Stopping (Fig. 28) automatically return to the original position once the Decrease engine speed, and push stop switch (21) to stop engine has started. (Fig. 25) position. Fig. 28 Fig. 25 6. -
Page 11: Maintenance
(L) screws on the carburetor. Those Spark plug (Fig. 31, 32, 33) are only for Tanaka dealer. If you rotate them, it will 1. Remove cleaner box (B) (32) and cleaner box (A) (37). cause a serious damage to the machine. -
Page 12: Monthly Maintenance
0 mm Anti-vibration systems (Fig. 35) Check the springs (40) for any loosening or damage. If you fi nd any failure in those parts, please contact a Tanaka dealer. Fig. 39 5. Assemble clutch cover and arm cover by following the aforementioned steps in reverse. -
Page 13: Troubleshooting
Spark plug is wet 2. Pull starter and dry the fuel inside the engine Engine does not start The fuel pipe is bent or detached Consult a Tanaka dealer Carburetor failure Consult a Tanaka dealer Spark plug failure Replace spark plug or correct the gap... - Page 16 Shinagawa Intercity Tower A, 15-1, Konan 2-chome, Minato-ku, Tokyo, Japan Code No. E99701111 NA Printed in China...