Related Manuals for Dell Inspiron 24-3459
Summary of Contents for Dell Inspiron 24-3459
- Page 1 Inspiron 24 3000 Series Service Manual Computer Model: Inspiron 24–3459 Regulatory Model: W12C Regulatory Type: W12C003...
- Page 2 WARNING: A WARNING indicates a potential for property damage, personal injury, or death. Copyright © 2015 Dell Inc. All rights reserved. This product is protected by U.S. and international copyright and intellectual property laws. Dell and the Dell logo are trademarks ™...
-
Page 3: Table Of Contents
Contents Before working inside your computer........9 ....................9 Before you begin ....................10 Safety instructions ..................11 Recommended tools After working inside your computer........12 Technical overview..............13 ................13 Inside view of your computer Removing the stand assembly..........14 ..............14 Procedure to remove easel stand ..............15 Procedure to remove pedestal stand ........ - Page 4 Replacing the optical drive............26 ......................26 Procedure ....................26 Post-requisites Removing the hard drive............27 .....................27 Prerequisites ......................27 Procedure Replacing the hard drive............30 ......................30 Procedure ....................30 Post-requisites Removing the memory module..........31 ..................... 31 Prerequisites ......................31 Procedure Replacing the memory module..........33 ......................33 Procedure ....................
- Page 5 Replacing the heat sink............41 ......................41 Procedure ....................41 Post-requisites Removing the fan..............42 .....................42 Prerequisites ......................42 Procedure Replacing the fan..............44 ......................44 Procedure ....................44 Post-requisites Removing the coin-cell battery..........45 .....................45 Prerequisites ......................46 Procedure Replacing the coin-cell battery..........47 ......................47 Procedure ....................
- Page 6 Replacing the camera............... 53 ......................53 Procedure ....................53 Post-requisites Removing the system board............54 .....................54 Prerequisites ......................54 Procedure Replacing the system board............ 57 ......................57 Procedure ....................57 Post-requisites Removing the VESA-mount bracket........58 .....................58 Prerequisites ......................58 Procedure Replacing the VESA-mount bracket........60 ......................
- Page 7 Replacing the speakers............66 ......................66 Procedure ....................66 Post-requisites Removing the control-buttons board........67 .....................67 Prerequisites ......................67 Procedure Replacing the control-buttons board........69 ......................69 Procedure ....................69 Post-requisites Removing the display assembly..........70 .....................70 Prerequisites ......................71 Procedure Replacing the display assembly..........75 ......................75 Procedure ....................
- Page 8 Clearing CMOS Settings............82 ....................82 Prerequisites ......................82 Procedure ....................83 Post-requisites Flashing the BIOS..............84 Getting help and contacting Dell...........85 ..................85 Self-help resources ....................86 Contacting Dell...
-
Page 9: Before Working Inside Your Computer
Before working inside your computer CAUTION: To avoid damaging the components and cards, handle them by their edges and avoid touching pins and contacts. NOTE: The images in this document may differ from your computer depending on the configuration you ordered. Before you begin Save and close all open files and exit all open applications. -
Page 10: Safety Instructions
CAUTION: You should only perform troubleshooting and repairs as authorized or directed by the Dell technical assistance team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. See the safety instructions that shipped with the product or at www.dell.com/regulatory_compliance. -
Page 11: Recommended Tools
Recommended tools The procedures in this document may require the following tools: • Phillips screwdriver • Plastic scribe... -
Page 12: After Working Inside Your Computer
After working inside your computer CAUTION: Leaving stray or loose screws inside your computer may severely damage your computer. Replace all screws and ensure that no stray screws remain inside your computer. Connect any external devices, peripherals, and cables you removed before working on your computer. -
Page 13: Technical Overview
Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Inside view of your computer control-buttons board hard-drive assembly optical-drive assembly... -
Page 14: Removing The Stand Assembly
After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Procedure to remove easel stand NOTE: The type of stand assembly varies depending on the configuration you ordered. -
Page 15: Procedure To Remove Pedestal Stand
Lift the stand off the back cover. stand stand bracket screws (2) back cover Procedure to remove pedestal stand NOTE: The type of stand assembly varies depending on the configuration you ordered. Place the computer face down on a soft cloth or a clean surface. Release the tabs on the stand cover. - Page 16 Slide and remove the stand cover away from the computer. stand cover back cover Remove the screws that secure the stand to the display-panel base. Lift the stand upward at an angle and slide it away from the computer. back cover screws (4) stand...
-
Page 17: Procedure To Remove Stand Riser From Stand Base
Procedure to remove stand riser from stand base NOTE: If you need to remove either the stand base or stand riser from the stand assembly, follow the steps below. Lift the screw handle on the stand base. Using the screw handle, loosen the captive thumbscrew that secures the stand base to the stand riser. - Page 18 Slide the stand base off the stand riser. stand riser stand base...
-
Page 19: Replacing The Stand Assembly
After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Procedure to replace easel stand NOTE: The type of stand assembly varies depending on the configuration you ordered. -
Page 20: Removing The Back Cover
Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Prerequisites Remove the stand assembly. Procedure CAUTION: Do not remove the computer cover unless you need to install internal accessories for your computer. - Page 21 Lift the back cover off the computer. display bezel back cover plastic scribe...
-
Page 22: Replacing The Back Cover
After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Procedure Align the tabs on the back cover with the slots on the display bezel and snap the back cover into place. -
Page 23: Removing The Optical Drive
Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Prerequisites Remove the stand assembly. Remove the back cover. - Page 24 Slide the optical-drive assembly out of the optical-drive bay. optical-drive assembly screw power and data cable Carefully pull the optical-drive bezel and remove it from the optical drive. Remove the screw that secures the optical-drive bracket to the optical drive.
- Page 25 Remove the optical-drive bracket from the optical drive. screw optical-drive bracket optical drive optical-drive bezel...
-
Page 26: Replacing The Optical Drive
After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Procedure Align the screw hole on the optical-drive bracket with the screw hole on the optical drive. -
Page 27: Removing The Hard Drive
After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. CAUTION: Hard drives are fragile. Exercise care when handling the hard drive. CAUTION: To avoid data loss, do not remove the hard drive while the computer is in sleep or on state. - Page 28 Using your fingertips, slide the hard-drive assembly out of the hard-drive bay. power and data cable hard-drive assembly screw display-assembly base Remove the screws that secure the hard-drive bracket to the hard drive.
- Page 29 Remove the hard drive from the hard-drive bracket. screws (3) hard drive hard-drive bracket...
-
Page 30: Replacing The Hard Drive
After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. CAUTION: Hard drives are fragile. Exercise care when handling the hard drive. Procedure Align the screw holes on the hard-drive bracket with the screw holes on the hard drive. -
Page 31: Removing The Memory Module
Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Prerequisites Remove the stand assembly. Remove the back cover. - Page 32 Remove the memory module from the memory-module slot. system board securing clips (2) memory module memory-module slot...
-
Page 33: Replacing The Memory Module
After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Procedure Align the notch on the memory module with the tab on the memory- module slot. -
Page 34: Post-Requisites
Slide the memory module firmly into the slot at an angle and press the memory module down until it clicks into place. NOTE: If you do not hear the click, remove the memory module and reinstall it. notch securing clips (2) memory module memory-module slot Post-requisites... -
Page 35: Removing The Wireless Card
Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Prerequisites Remove the stand assembly. Remove the back cover. - Page 36 Slide the wireless card out of the wireless-card slot. wireless-card bracket antenna cables screw wireless-card slot wireless card system board...
-
Page 37: Replacing The Wireless Card
After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Procedure Align the notch on the wireless card with the tab on the wireless-card slot. -
Page 38: Post-Requisites
Replace the screw that secures the wireless-card bracket and the wireless card to the system board. antenna cables wireless-card bracket screw wireless card wireless-card slot notch Post-requisites Replace the back cover. Replace the stand assembly. -
Page 39: Removing The Heat Sink
After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. WARNING: The heat sink may become hot during normal operation. Allow sufficient time for the heat sink to cool before you touch it. - Page 40 Lift the heat sink off the system board. system board captive screws (5) heat sink screw display-assembly base...
-
Page 41: Replacing The Heat Sink
After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. CAUTION: Incorrect alignment of the heat sink can damage the system board and processor. NOTE: The original thermal grease can be reused if the original system board and heat sink are reinstalled together. -
Page 42: Removing The Fan
Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Prerequisites Remove the stand assembly. Remove the back cover. - Page 43 Lift the fan at an angle off the display-assembly base. fan cable system board screws (2) display-assembly base...
-
Page 44: Replacing The Fan
After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Procedure Replace the fan at an angle on the display-assembly base. Align the screw holes on the fan with the screw holes on the display- assembly base. -
Page 45: Removing The Coin-Cell Battery
After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. CAUTION: Removing the coin-cell battery resets the BIOS setup program’s settings to default. It is recommended that you note the BIOS setup program’s settings before removing the coin-cell battery. -
Page 46: Procedure
Procedure Using a plastic scribe, gently pry out the coin-cell battery out of the battery socket on the system board. system board plastic scribe coin-cell battery battery socket... -
Page 47: Replacing The Coin-Cell Battery
After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Procedure With the positive-side facing up, insert the coin-cell battery into the battery socket and press down the battery into place. -
Page 48: Removing The Microphone
Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Prerequisites Remove the stand assembly. Remove the back cover. - Page 49 Disconnect the microphone and camera cable from the microphone board. microphone and camera routing guides cable display bezel display-assembly base microphone board...
-
Page 50: Replacing The Microphone
After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Procedure Connect the microphone and camera cable to the microphone-board. Slide the microphone board into the slot on the display bezel. -
Page 51: Removing The Camera
Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Prerequisites Remove the stand assembly. Remove the back cover. - Page 52 Disconnect the microphone and camera cable from the camera module. securing clip camera module microphone and camera cable...
-
Page 53: Replacing The Camera
After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Procedure Connect the microphone and camera cable to the camera module. Push the tabs on the camera module into the tab on the camera-module slot. -
Page 54: Removing The System Board
After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. NOTE: Your computer’s Service Tag is stored in the system board. You must enter the Service Tag in the BIOS setup program after you replace the system board. - Page 55 Press the latch and disconnect the display-backlight cable from its connector on the system board. speaker cable touch-control board cable control-buttons board display-backlight cable cable display cable display-assembly base hard-drive data cable optical-drive data cable hard-drive and optical-drive 10 fan cable power cable microphone and camera cable...
- Page 56 Carefully lift the system board from the inner edge and release the ports from the slots on the display-assembly base. Lift the system board off the display-assembly base. system board slots screws (4) display-assembly base...
-
Page 57: Replacing The System Board
After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. NOTE: Your computer’s Service Tag is stored in the system board. You must enter the Service Tag in the BIOS setup program after you replace the system board. -
Page 58: Removing The Vesa-Mount Bracket
Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Prerequisites Remove the stand assembly. Remove the back cover. - Page 59 Lift the VESA-mount bracket off the display-assembly base. display-assembly base screws (4) VESA-mount bracket speaker cable routing guides...
-
Page 60: Replacing The Vesa-Mount Bracket
After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Procedure Align the screw holes on the VESA-mount bracket with the screw holes on the display-assembly base. -
Page 61: Removing The Speaker Cover
Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Prerequisites Remove the stand assembly. Remove the back cover. - Page 62 Lift the speaker cover off the display bezel. screws (4) speaker cover display-assembly base...
-
Page 63: Replacing The Speaker Cover
After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Procedure Align the screw holes on the speaker cover with the screw holes on the display-assembly base and snap the speaker cover into place. -
Page 64: Removing The Speakers
Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Prerequisites Remove the stand assembly. Remove the back cover. - Page 65 Lift the speakers, along with the speaker cable, off the display bezel. screw tape speaker-cable routing VESA-mount bracket speaker cable rubber grommets (4) speakers (2)
-
Page 66: Replacing The Speakers
After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Procedure Using the alignment posts and rubber grommets on the display bezel, place the speakers on the display bezel. -
Page 67: Removing The Control-Buttons Board
Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Prerequisites Remove the stand assembly. Remove the back cover. - Page 68 Lift the latch and disconnect the control-buttons board cable from the control-buttons board. latch system board control-buttons board latch cable control-buttons board securing clips (2)
-
Page 69: Replacing The Control-Buttons Board
After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Procedure Slide the control-buttons board cable into the connector on the control- buttons board and press down on the latch to secure the cable. -
Page 70: Removing The Display Assembly
Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Prerequisites Remove the stand assembly. Remove the back cover. -
Page 71: Procedure
Procedure Note the optical drive and hard drive cables' routing and remove the cables from its routing guides on the display-assembly base. routing guides hard-drive cable optical-drive cable display-assembly base... - Page 72 Remove the screws that secure the display-assembly base to the display bezel. screws (19) display-assembly base Release the display-panel base from the tabs on the display bezel. Slide the display cable through the slot on the display-assembly base.
- Page 73 Lift the display-assembly base off the display panel. tabs (6) display-assembly base display cable slot...
- Page 74 display assembly...
-
Page 75: Replacing The Display Assembly
After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Procedure Slide the display cable through the slot on the display-assembly base. Slide the tabs on the display bezel into the slots on the display-assembly base. - Page 76 15 Replace the back cover. 16 Replace the stand assembly.
-
Page 77: Removing The Rubber Feet
Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Prerequisites Remove the stand assembly. Remove the back cover. - Page 78 Lift the rubber feet off the display bezel. rubber feet (2) screws (2) display bezel...
-
Page 79: Replacing The Rubber Feet
After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Procedure Align the screw holes on the rubber feet with the screw holes on the display bezel. -
Page 80: Clearing Forgotten Passwords
Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Prerequisites Remove the stand assembly. Remove the back cover. -
Page 81: Post-Requisites
Wait for 5 seconds and then replace the jumper plug in its original location. jumper plug password jumper-pins Post-requisites Replace the back cover. Replace the stand assembly. -
Page 82: Clearing Cmos Settings
Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/regulatory_compliance. Prerequisites Remove the stand assembly. Remove the back cover. -
Page 83: Post-Requisites
Wait for 5 seconds and then replace the jumper plug to its original location. jumper plug Password jumper-pins CMOS jumper-pins Post-requisites Replace the back cover. Replace the stand assembly. -
Page 84: Flashing The Bios
You may need to flash (update) the BIOS when an update is available or when you replace the system board. To flash the BIOS: Turn on the computer. Go to www.dell.com/support. Click Product Support, enter the Service Tag of your computer and click Submit. -
Page 85: Getting Help And Contacting Dell
Getting help and contacting Dell Self-help resources You can get information and help on Dell products and services using these self-help resources: Information about Dell products and www.dell.com services Windows 8.1 and Windows 10 Dell Help & Support app Windows 10 Get started app Windows 8.1... -
Page 86: Contacting Dell
Contacting Dell To contact Dell for sales, technical support, or customer service issues, see www.dell.com/contactdell. NOTE: Availability varies by country and product, and some services may not be available in your country. NOTE: If you do not have an active internet connection, you can find contact information on your purchase invoice, packing slip, bill, or Dell product catalog.