KingShield THPW1-CB Installation & Operating Instructions

Installation / Operating Instructions
for Wireless Digital Programmable Thermostat
- THPW1-CA, THPW1-CB, THPW1-CC,
THPW1-CD & THPW1-CE
Our latest microprocessor controlled programmable thermostat
has been designed to reduce your heating and air-conditioning
bill. The THPW1 is made to be user friendly and easy to use.
SAFETY INSTRUCTIONS
Please read these instructions fully before
attempting installation.
This unit should be installed by a competent person in
accordance with the current IEE Wiring Regulations.
If in doubt consult a qualified electrician
GENERAL
The THPW1 digital programmable thermostat consists of the
thermostat transmitter and the remote mains operated receiver
unit.
It has 7 days preset programs which can be tailored to suit your
lifestyle.
The THPW1 transmitter is operated by 2 x AA size batteries and
can replace any mechanical standard 2 wire thermostat.
Please note that the maximum resistive load is 16A.
These units are paired during manufacture and the operating
channel is given by a letter code. When installing more than one
unit in a system ensure each thermostat pair has a different letter
code.
INSTALLATION
1. You should place the thermostat as following:
a. About 160cm up from the floor.
b. Only on inside walls (not on an outside wall).
c. Do not expose to direct sun light.
d. Do not position close to a heater, ventilation outlet or
close to an outside door.
2. Remove the front cover. Unscrew the screw in the battery
compartment. Remove the front housing from the base.
3. Using the base as a template, drill two holes in the wall and
secure the base with appropriate wall plugs and screws.
4. Replace the front housing onto base and replace the screw
in battery compartment.
5. Install 2 x AA size batteries into battery compartment and
replace front case.
6. Press the reset button once to enter time set mode.
Features of the LCD display and keys:
THPW1 LCD display
Fig 1
Description of each key function: Fig 2
- To enter into program mode
- To view an Temperatures
- To enter into time and day adjustment mode
Reset - To reset the unit into initial mode
- To turn the unit on or off
- To enter into Vacation mode
- To confirm setting
- To override into CT (COMFORT Temperature) mode (20°C)
- To override into ET (ECONOMY Temperature) mode (17°C)
- Temporary temperature override mode or increase
value adjustment
- Temporary temperature override mode or decrease
value adjustment
OPERATION AND PROGRAMMING INSTRUCTIONS
To set clock and day:
After the batteries (2 x AA size) have been installed into the
thermostat unit, or reset or key is pressed, the thermostat is
in time adjustment mode.
The hour is flashing. Press or key to adjust hour.
Press key to confirm setting. The minute is flashing.
Press or key to adjust minute. Press key to confirm
setting. The day is flashing. Press or key to adjust day.
Press key to confirm setting. This will
confirm the setting of time and day.
The display will return into running mode.
E.g. If you have set the clock at 8.30 FRIDAY
and the room temperature is 25°C.
The display will display in Fig 3.
To view programs:
THPW1 thermostat is a weekly programmable thermostat, and
each day can be programmed separately.
Each hour can select or temperature. However a weekly
factory preset program is installed.
This preset program is set to suit most families life style. See
table 3.1 for factory preset program.
Fig 3.1
Press key. The Monday preset program at 0.00 is on display.
Press or key the display will show the temperature setting in
each hour. E.g. Monday program show 0:00 - 5:59 and 8:00 -
15:59 are set at evening temp.,6:00 - 7:59 and 16:00 - 22:59 is
set at CT. Note 23:00 - 0:00 is set at ET.
Press key the next day preset program is displayed. Again
Press or key. This will show the temperature setting at each
hour. Repeat above steps, each preset program will display until
Sunday. Once Sunday program has been reviewed. Press
The display will return into running mode.
To change preset program:
The preset program may not be suitable for some families but
the program may be adjusted to suit your living life style.
The following instruction will allow you to change the preset
program.
Press key to enter into program viewing mode.
Press key to select the day of program to make a change.
Press or key to select the hour to make change. Press
to select the temperature to make change. E.g. To change
Saturday 12:00 - 16:59 from CT to 12:00 - 16:59 ET.
1. Press key to enter into program viewing mode.
2. Press key to select the day to Saturday program.
3. Press key until 12:00 with CT setting.
Fig 3
4. Press key to change CT period to ET period.
5. Repeat step 3 & 4 to change 13:00 - 14:00 from CT period to
ET period.
6. Press
key to confirm setting. Press
running mode.
7. You can review the program on
Saturday to check the program and
confirm the setting (Fig 4).
Important
Note: Do not set the beginning and end of the program to 0:00
due to the thermostat needing this time for its reference use.
Therefore you must set the beginning or end time at 23:00 or
01:00.
To view and change or temperature:
The CT and ET temperature is preset at below table for heating
and air-conditioning mode:
Mode Air-conditioning
23 c
key.
28 c
or
key to return into
Fig 4
Heating
20 c
17 c