Subscribe to Our Youtube Channel
Related Manuals for Moxa Technologies ZB-DCU3-T
Summary of Contents for Moxa Technologies ZB-DCU3-T
- Page 1 Moxa Industrial Sub-1G Module ZB-DCU3-T, ZB-PM3-T, ZB-WAN1-T User’s Manual First Edition, August 2014 www.moxa.com/product © 20 Moxa Inc. All rights reserved. Reproduction without permission is prohibited.
- Page 2 Moxa Industrial Sub-1G Module ZB-DCU3-T, ZB-PM3-T, ZB-WAN1-T User’s Manual The software described in this manual is furnished under a license agreement and may be used only in accordance with the terms of that agreement. Copyright Notice © 2014 Moxa Inc. All rights reserved.
-
Page 3: Table Of Contents
Table of Contents 1. Introduction ......................1-1 Overview ..................1-2 Features ..................1-2 Specifications ................1-2 2. Getting Started ....................2-1 Module Layout ................2-2 Block Diagram ............2-2 Connector Locations ..............2-3 Hardware Installation ............. 2-3 Software Installation ............2-3 A. -
Page 4: Introduction
Introduction The following topics are covered in this chapter: Overview Features Specifications... -
Page 5: Overview
Overview Moxa Sub-1G module(ZB-DCU3-T, ZB-PM3-T, ZB-WAN1-T) uses ATMEL wireless microcontroller which provides a comprehensive solution with large memory(256KB Flash and 16KB SRAM), high CPU and radio performance and all RF components included. The module is a range of ultra low power, high performance surface mount modules targeted at Sub-1G networking applications, enabling users to realize products with minimum time to market and at the lowest cost. - Page 6 Operating Temperature: -40 to 75°C (-40 to 167°F) Operating Humidity: 5 to 95% RH Storage Temperature: -40 to 85°C (-40 to 185°F) Physical Characteristics Dimension: ZB-DCU3-T/ZB-WAN1-T (48x30x1.6mm), ZB-PM3-T (45x38x1.6mm) Standard and Certifications EMC: CE (EN55022 and EN55024 Class A), FCC Part 15 Subpart B Class A Reliability...
-
Page 7: Getting Started
Getting Started This chapter covers the module layout, and block diagram, hardware installation of the Sub-1G module. Software installation is covered in the next chapter. Module Layout Block Diagram Connector Locations Hardware Installation Software Installation... -
Page 8: Module Layout
Module Layout ZB-DCU3-T, ZB-WAN1-T ZB-PM3-T Block Diagram... -
Page 9: Hardware Installation
Computer system and Power Meter. Steps for Installation on DCU 1. Attach the WLAN antenna to connector UI. 2. Let Sub-1G Module(ZB-DCU3-T and ZB-WAN1-T) connect to DCU-8620-T. 3. Screw on the Sub-1G Module Steps for Installation on Power Meter 1. Let Sub-1G Module(ZB-PM3-T) connect to Power Meter. -
Page 10: Software Installation
Steps for Installation 1. Apply power to the system board. 2. Run DCU-8620-T application program. Make sure it could communicate with Sub-1G module(ZB-WAN1-T and ZB-DCU3-T). 3. Apply power to the Power Meter. Make sure the LED of “Ready” light-on on Power Meter. -
Page 11: Regulatory Statements
Regulatory Statements Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. - Page 12 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: “Contains FCC ID: SLE-ZB-PM3-T” or “Contains FCC ID: SLE-ZB-DCU3-T”. The grantee's FCC ID can be used only when all FCC compliance requirements are met.
Need help?
Do you have a question about the ZB-DCU3-T and is the answer not in the manual?
Questions and answers