Advertisement
3gb05564.fm Page 2 Tuesday, February 3, 2004 4:17 PM
CONSUMPTION DATA
Load
Programme
(kg)
Cotton 95°
5.5
Cotton 60°
5.5
Cotton 40°
5.0
Daily 40°
3.0
Synthetics 40°
2.5
Delicate 40°
1.5
Wool 40°
1.0
Silk 30°
1.0
Prewash might increase programmme duration. Consumption values were measured in normalized conditions in compliance
with Standard IEC 60 456.
Consumption data in the home may vary with respect to the values in the table in relation to the water supply pressure and
temperature, the load and the type of wash.
ADD DETERGENTS, CLOSE THE DOOR AND
SELECT THE PROGRAMME
Add the detergent as described in the programme
table or in the chapter "Detergents and Additives" in
the booklet.
1. Open the tap.
2. Set the programme selector to the desired
programme.
3. Set the spin selector to the desired speed.
4. Special options can be selected.
5. Check that the door is well closed and turn on the
washing machine by pressing the "ON/OFF"
button. The indicator lights up, indicating that the
washing machine is on.
Black process 45.0° 100.0 LPI
Water
Energy
Approx.
Programme
Duration
(l)
(kWh)
(hours:minutes)
54
1.90
2:05
49
1.04
2:25
44
0.60
2:10
50
0.60
1:00
55
0.60
1:25
60
0.60
0:50
60
0.45
0:45
60
0.30
0:45
SELECT ANY DESIRED OPTION
"Quick Wash" button
• For quick, economical washes.
• Ideal for minimum loads of lightly-soiled articles.
Note: reduce the detergents quantity.
"Rinse Hold" button
• The laundry remains in the last rinse water
without progressing to the final spin cycle to avoid
creasing and prevent colours from changing.
• This option is particularly recommended for the
programme "Synthetics" or "Delicates".
• This function is particularly useful if you want to
postpone spinning to a later time, or if you want to
drain only.
Terminate the "Rinse Hold" option:
• Press the "Rinse Hold" button again; the
programme will terminate automatically with the
final spin cycle for the present wash programme.
• If you do not wish to spin the clothes, turn the
programme selector knob counterclockwise to
the "Drain" programme.
"Cold Wash" button
• With this option water is heated only up to 20°C.
PROGRAMME CHANGE
To reselect a programme when a cycle has already
begun:
1. Switch off the appliance by pressing the
"ON/OFF" button.
2. Select the new programme.
3. Start the programme by pressing the "ON/
OFF" button.
PROGRAMME END
1. At the end of the programme the programme
selector moves to the stop position.
2. To unload the machine wait for the door to
unlock (about 1 minute).
3. Switch off the appliance, open the door and
take out the laundry.
4. Close the tap and leave the door ajar to allow
the drum to dry out.
NOTES AND INDICATIONS FOR USE
•
WATER LEVEL
It may not be visible as the cycle is optimised
for a minimum water consumption without
compromising washing results.
•
SPIN SPEED CONTROL
Spin speed may be reduced automatically or
may even be excluded in the case of small
loads with highly absorbent garments (e.g.
bathrobes, bathmat).
This control avoids cloth and machine damage
and excessive vibrations and consequent noise
produced by the machine due to load
unbalance: by selecting high spin speeds the
noise level increases.
•
MOTOR NOISE
The running noises of the new, electronically-
controlled motor are not the same as the
ones you are used to from your old appliance.
Don't be surprised - modern technology has a
modern sound.
•
CLEANING THE FILTER
To ensure an impeccable function of the
pump, check the filter regular and clean it if
necessary.
Whirlpool is a registered trademark of Whirlpool USA.
5019 301 05564
Advertisement
