Subscribe to Our Youtube Channel
Related Manuals for Schiller LITTLE WONDER BRC-26 HYDRO
Summary of Contents for Schiller LITTLE WONDER BRC-26 HYDRO
- Page 1 LITTLE WONDER ® BRC-26 HYDRO 26” LITTLE WONDER BRUSH CUTTER MODELS: 5126-22-59 HONDA GX390...
- Page 2 CALIFORNIA WARNING Proposition 65 Warning Diesel engine exhaust and some The engine exhaust from this product of its constituents are known to the contains chemicals known to the State State of California to cause cancer, of California to cause cancer, birth birth defects and other reproductive defects or other reproductive harm.
-
Page 3: Table Of Contents
Your safe use of this Schiller Grounds Care, Inc� product is one of our prime design objectives� Many safety features are built in, but we also rely on your good sense and care to achieve accident-free operation�... -
Page 4: Safety
Schiller of hazard seriousness� These words appear in this Grounds Care, Inc� Engineering Department� Any manual and on the safety labels attached to Schiller Schiller Grounds Care, Inc� product that is altered, Grounds Care, Inc� machines� For your safety and... - Page 5 SAFETY BRUSH CUTTER OPERATOR PREPARATION AND SITE PREPARATION AND CIRCUMSTANCES TRAINING • Evaluate the terrain to determine how to safely perform the job� Only use accessories and READ THE OPERATION & attachments approved by the manufacturer� SAFETY MANUAL • Clear the area to be cut of objects such as rocks, toys, wire or any other debris that may be thrown or •...
- Page 6 SAFETY BRUSH CUTTER WARNING INTERRUPTING OPERATION Before leaving the operator’s position: -Park on level ground� -Disengage blade� -Shut off the engine and remove the key • Disengage the blade, and wait until the blade stops rotating: - When not cutting� All rotary blade machines are potentially - When crossing surfaces other than grass�...
- Page 7 SAFETY BRUSH CUTTER OPERATING ON SLOPES MAINTENANCE SAFETY In general EXTRA CARE WHEN OPERATING ON • Maintain machine according to manufacturer's SLOPES. EVALUATE THE RISKS INVOLVED BEFORE schedule and instructions for maximum safety and OPERATING ON A SLOPE best results� �...
- Page 8 SAFETY BRUSH CUTTER Blades STORAGE SAFETY WARNING • The blade is sharp and can cut� • Stop the engine and allow to cool before storing� Use extra caution when handling� • Drain the fuel tank outdoors only� Remove obstructions with care� •...
-
Page 9: Labels
LABELS BRUSH CUTTER WARNING LABELS Warning labels are an important part of the safety system incorporated in this machine� Replace labels if damaged or illegible� NOTICE TO AVOID PREMATURE FAILURE OF CLUTCH, ENSURE LINKAGES ARE ADJUSTED PROPERLY. PLEASE READ MANUAL FOR DETAILS. - Page 10 LABELS BRUSH CUTTER WARNING LABELS Warning labels are an important part of the safety system incorporated in this machine� Replace labels if damaged or illegible� Blade Control - Hold lever down to engage blade� - Release lever to stop blade� 4167101 Fuel Valve - Turn counter-clockwise for ‘ON’�...
-
Page 11: Controls
SET-UP INSTRUCTIONS / CONTROLS BRUSH CUTTER CONTROLS THROTTLE CONTROL (D) Controls engine speed� Pushing the lever forward BLADE CONTROL LEVER (A) makes the engine speed go faster, while pulling Hold down the lever to engage the blade for cutting� the lever back slows down the speed of the engine� Release the lever to disengage and stop the blade�... -
Page 12: Operation
OPERATION BRUSH CUTTER PRE-OPERATION CHECK LIST BEFORE STARTING THE ENGINE OWNER’S RESPONSIBILITY • Read the operator manual and engine manual� • Be familiar with all controls, how each functions and • Review and follow all safety rules and safety decal what each operates�... - Page 13 OPERATION BRUSH CUTTER MOVING THE UNIT CUTTING WARNING UNDERGROUND UTILITIES, TO MOVE THE UNIT WITHOUT THE BLADE ELECTROCUTION, EXPLOSION, SERVICE RUNNING: DISRUPTION RISK 1� Do not engage the blade control lever� Before beginning any work, check area for 2� Lift the free-wheel rod until the enlarged boss pops exposed utilities�...
-
Page 14: Maintenance
2� Remove the four bolts Q securing the Blade belt When replacement parts are required, use genuine Schiller Grounds Care, Inc� parts or parts with cover S� (Figure 1) equivalent characteristics, including type, strength and material� Failure to do so may result in product 3�... - Page 15 MAINTENANCE BRUSH CUTTER Use an impact wrench to remove the blade bolt F� If an impact wrench is not available; use a socket on a Check oil level daily� Top off as needed� long breaker bar or a box wrench to loosen the blade Change engine oil after the first 5 hours of operation.
- Page 16 MAINTENANCE BRUSH CUTTER LUBRICATION There are 5 grease fittings on the machine. A--Blade Spindle- Grease 1 pump once a season� CAUTION: Do not over grease or the bearing seals can be popped out or crushed� B--Transaxle Idler Pivot- Grease once a season� C--Brake Bellcrank- Grease once a season�...
-
Page 17: Adjustments
ADJUSTMENTS BRUSH CUTTER BELTS Under tensioned V-belts can slip and squeal� This generates excess heat and results in cracking and premature belt failure� Over-tensioned belts reduce belt and bearing life� Properly tensioning and aligning a belt drive will allow the belt drive to perform at it’s maximum level� Stop the engine and remove the spark plug wire before making any belt adjustments. -
Page 18: Storage
ADJUSTMENTS BRUSH CUTTER STORAGE To prevent possible explosion or ignition of vaporized fuel, do not store equipment with fuel in tank or carburetor in an enclosure with open flame (for example, a furnace or water heater pilot)� DAILY STORAGE 1� Stop the engine� 2�... -
Page 19: Troubleshooting
TROUBLESHOOTING BRUSH CUTTER TROUBLESHOOTING COMMON PROBLEMS COMMON CAUSES ENGINE WILL NOT START. • Refer to the section “Operation” in this manual to verify engine starting procedure� (Check the Engine Manual for more • Check the spark plug connection� details�) • Check that throttle lever is set to the “FAST”... -
Page 20: Specifications
• Check for a broken or bent blade� DO NOT straighten blade� Replace bent or broken blade with a new Schiller Grounds Care, Inc� blade� • If the blade appears to be in good condition, check the bolt connecting the blade and verify that it is tightened and properly seated�... -
Page 21: Declaration Of Conformity
EC Declaration of Conformity 4169805 REV A The Undersigned Manufacturer: Schiller Grounds Care, Inc� Kurt Knudsen One Bob-Cat Lane Director of Operations Johnson Creek, WI 53038 Date: 23rd Septemeber 2013 EU Authorized Representative: Earlsmere Limited Unit 18 Valley Road Jim White... -
Page 22: Warranty
Schiller Grounds Care’s responsibility under this limited warranty is restricted to repairing or replacing, at its purchaser only, and under the following terms and conditions. Schiller Grounds Care’s responsibility option, any covered part found to be defective in material or workmanship during the warranty period�... - Page 23 Operator’s Manual; or (ii) has been altered or modifi ed so as to adversely affect its operation, performance or durability, or that has been altered or modifi ed in ways not approved by Schiller Grounds Care.
Need help?
Do you have a question about the LITTLE WONDER BRC-26 HYDRO and is the answer not in the manual?
Questions and answers