Pioneer SC-LX501 Manual page 48

> Specifications > Settings
■ Channel Level
Setting Item Default Value
Front Left 0.0 dB
Center 0.0 dB
Front Right 0.0 dB
Height Left 0.0 dB
Height Right 0.0 dB
Surround Right 0.0 dB
Surr Back Right 0.0 dB
12
> Listening Modes > Playback Function
Setting Details
Select a value between "−12.0 dB" and "＋12.0
dB" (in 0.5 dB increments). A test tone will be
output each time you change the value. Select the
desired level.
Select a value between "−12.0 dB" and "＋12.0
dB" (in 0.5 dB increments). A test tone will be
output each time you change the value. Select the
desired level.
Select a value between "−12.0 dB" and "＋12.0
dB" (in 0.5 dB increments). A test tone will be
output each time you change the value. Select the
desired level.
Select a value between "−12.0 dB" and "＋12.0
dB" (in 0.5 dB increments). A test tone will be
output each time you change the value. Select the
desired level.
• The setting cannot be changed if "Zone 2" is set
in "System Setup" - "Speaker" - "Configuration"
- "Zone Speaker" and Zone 2 is on.
Select a value between "−12.0 dB" and "＋12.0
dB" (in 0.5 dB increments). A test tone will be
output each time you change the value. Select the
desired level.
• The setting cannot be changed if "Zone 2" is set
in "System Setup" - "Speaker" - "Configuration"
- "Zone Speaker" and Zone 2 is on.
Select a value between "−12.0 dB" and "＋12.0
dB" (in 0.5 dB increments). A test tone will be
output each time you change the value. Select the
desired level.
Select a value between "−12.0 dB" and "＋12.0
dB" (in 0.5 dB increments). A test tone will be
output each time you change the value. Select the
desired level.
Setting Item Default Value
Surr Back Left 0.0 dB
Surround Left 0.0 dB
Subwoofer 0.0 dB
■ Dolby Enabled Speaker
Setting Item Default Value
Dolby Enabled 6.0ft/1.80m
Speaker to
Ceiling
Reflex Optimizer Off
> Basic Manual
Troubleshooting | Appendix
Setting Details
Select a value between "−12.0 dB" and "＋12.0
dB" (in 0.5 dB increments). A test tone will be
output each time you change the value. Select the
desired level.
Select a value between "−12.0 dB" and "＋12.0
dB" (in 0.5 dB increments). A test tone will be
output each time you change the value. Select the
desired level.
Select a value between "−15.0 dB" and "＋12.0
dB" (in 0.5 dB increments). A test tone will be
output each time you change the value. Select the
desired level.
Setting Details
Set the distance between the Dolby Enabled
Speaker and the ceiling. Select between
"0.1ft/0.03m" to "15.0ft/4.50m" (0.1ft/0.03m units).
• The unit of distance (ft/m) shown is the unit
selected for use in "Distance".
You can enhance the reflection effect of Dolby
Enabled Speakers from the ceiling.
"Off": Do not use this function
"On": Use this function
• The function is not effective if the listening mode
is Pure Direct.