Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Modena BZ 1050 DASS
Summary of Contents for Modena BZ 1050 DASS
- Page 1 User Manual Book Blast Chiller & Freezer BZ 1050 DASS BZ 1100 DASS BZ 1130 DASS...
-
Page 2: Table Of Contents
Lock/Unlock Control Panel ON/OFF Button Part 4: Maintenance Cleaning and Maintenance Part 5: Troubleshooting Part 6: Specification This guide book explains everything you need to know about your new product. Please contact our Customer Care should you need further assistance through www.modena.com. -
Page 3: Part 1: Safety Information
PART 1: SAFETY INFORMATION Read the user manual book carefully • Keep ventilation openings, in the appliance enclosure or in the built- in structure, clear of obstruction. • Do not use mechanical devices or other means to accelerate the defrosting process, other than those recommended by the manufacturer. -
Page 4: Environmental Notice
Environmental Notice The packaging material used is recyclable. We recommend that you separate plastic, paper and cardboard and give them to recycling agents. To help preserve the environment, the refrigerant used in this product is iso-butane (R600a) or propane (R290), which does not affect the ozone layer and has little impact on the greenhouse effect. -
Page 5: Part 3: Quick Start Guide
PART 3: QUICK START GUIDE General Features The chilling and freezing cycle is programmed according to International Food Safety Standards. There are 4 (four) types of cycle: Cy1: For fast chilling and conservation of foods at positive temperature 2. Cy2: For chilling and fast freezing of foods with holding 3. - Page 6 Keyboard in Stand-by Mode How to Select a Cycle: Push and release the (3) button until the desired cycle is selected. How to Start a Cycle: Push and release the (2) button. The correspendent yellow LED is switched on, How to Temporarily Stop the Running Cycle: Press and release the (2) button.
- Page 7 PHASE DISPLAY: pushing PH1 = phase 1 the UP key PH2 = phase 2 the running phase is PH3 = phase 3 displayed HOW TO DISPLAY THE REGULATION SET POINTS: By pushing the SET key the following information are displayed in sequence: •...
- Page 8 HOW TO MODIFY THE ROOM SET POINT While SETH is displayed hold pushed the SET key till the SETH label starts flashing and LED near the SET key is turned on. Use the arrow key to modify the value and the SET key to confirm it.
- Page 9 • CyC=enabled the printing of cycle parameters. • PtH=enabled the printing during the holding phase. • PrS=level Pr1 o Pr2. • Pnu=number of printing. • DOWN key back to the previous label. • To confirm: push the SET key. • To exit the Printer menu: push both SET+UP keys or wait for 5 sec.
-
Page 10: Defrost
LED Light Meaning Mode Description Compressor is enabled Programming Phase (flashing with LED Flashing Anti-short cycle delay enabled Fan is enabled Programming Phase (flashing with LED Flashing Anti-short cycle delay enabled Defrost is enabled Flashing Drip time in progress An alarm is occuring 1, 2, 3, Freezing cycle 1, 2, 3, 4 or hold mode active 4, H... - Page 11 HOLD PHASE: To select H symbol pushing the Cycles are pre-set with the following values: • Cy1: for fast chilling and conservation of foods (hard +soft chill). • Cy2: for chilling and fast freezing of foods (hard +soft + freezing cycle).
- Page 12 First phase: Hard Chill It is usually used to blast chill food just cooked. It is normally used to fast chill hot foods. (e.g., from 80°C / 170°F to 20°C / 70°F). During “Hard Chill”, both compressor and fan are always on until the rS1 temperature is reached.
- Page 13 Alarms Message Cause Output Data or Alarm output ON. Other outputs unchanged memory failure Thermostat Alarm output ON. Compressor output according to Probe failure parameters Con and CoF Evaporator Alarm output ON. Defrost termination is timed. No Probe failure temperature control on fans. i1P, i2P, Insert probe 1, Alarm output ON.
-
Page 14: Part 4: Maintenance
PART 4: MAINTENANCE Cleaning and Maintenance To make sure that the freezer is in optimum condition, the interior and accessories must be cleaned regularly. IMPORTANT! Appliance must not be connected to the main electrical socket during cleaning! Risk of electric shock! •... - Page 15 IMPORTANT! There are some normal sounds during use (compressor sound, circulating refrigerant sounds) Problem Possible Cause Recommended Action Appliance does • • Power cord is unplugged Insert power cord not work or loose correctly • • Blown fuse or damaged Check the fuse, replace if fuse needed...
-
Page 16: Part 6: Specification
PART 6: SPECIFICATION MODEL BZ 1050 DASS BZ 1100 DASS BZ 1130 DASS Capacity (Liter) Power Input (Watt) 1200 Color Stainless Stainless Stainless Control panel Digital Digital Digital Refrigerant (Weight) R290 (150g) R290 (150g) R290 (150g) Rated Curent (A) Rated Voltage (V) - Page 17 APPENDIX 1: CYCLE PARAMETERS Para mete Parameter Description Cycle setting; tEP = by temperature Defrost before cycle Insert probe set point: (-50 to 50, res. 1°C or 1°F) when the temperature 20°C 10°C -18°C -18°C measured by the three insert (68°F) (50°F) (0°F)
- Page 18 05/23 PT MODENA INDONESIA Jl. Industri Raya I Blok D-8, Jatiuwung, Tangerang 15135...
Need help?
Do you have a question about the BZ 1050 DASS and is the answer not in the manual?
Questions and answers