Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Waveband WVX-TWC6M-MT16
Summary of Contents for Waveband WVX-TWC6M-MT16
- Page 1 Six Unit Rapid Charger USER MANUAL...
-
Page 2: Table Of Contents
Waveband Six-Unit Charger Table of Contents Topic Page Introduction Important (read before use) Caution (read before use) Charger Features Replacing A Charging Pod Charging A Battery Fault Conditions & Advisements Warranty And Service Specifications Accessories... -
Page 3: Introduction
(Li-Ion), lithium polymer (LiPo), nickel-metal hydride (NiMH), or nickel cadmium (NiCd). If you wish to replace the charging pod in the future, check with Waveband customer service to ensure the replacement pod selected is compatible with your model. For a... -
Page 4: Important (Read Before Use)
Important Read all Caution statements below and this User Manual before attempting to charge a battery. Check to make sure a charging pod compatible with your battery is properly installed before charging a battery or installing the charger in a vehicle. Always charge new batteries completely before initial use. -
Page 5: Caution (Read Before Use)
Do not attempt to charge a battery without first installing the appropriate charging pod. Use only charging pods designed for this Waveband charger. Disconnect charger from the power source before installing, adjusting, or removing the charging pod. - Page 6 Caution (continued) Do not remove the charger’s housing or make any modification to the charger. Use only the power supply or DC power accessories specified for this Waveband charger. If a replacement is required, see section Accessories. Use of other power supplies or DC power accessories may damage the charger or batteries you may be attempting to charge.
-
Page 7: Charger Features
Charger Features DC power connection port - for hardwire kit. Charge status LED – shown for one position Power on / off switch. only. DC power connection port – for AC Status LED information – also see bottom to DC power supply or vehicle power label. - Page 8 Charger Features (continued) AC to DC power supply. DC power plug – connects to charger. 10. Power cord to connect power supply to AC outlet.
-
Page 9: Replacing A Charging Pod
Follow these steps to change the charging pod: Obtain a charging pod made specifically for this Waveband charger. Confirm that the charging pod is compatible with the battery you want to charge. -
Page 10: Charging A Battery
Charging A Battery Confirm that the charging pod and battery are compatible. Connect the charger to power with the power supply included. Place the battery to be charged in the charging pod. The battery may also be charged while attached to the radio. When a battery is placed in the charging pod and while charging, the status LED will illuminate RED with no flashing to indicate normal charging. - Page 11 Charging A Battery (Continued) After removing a fully charged battery, the charge status LED will illuminate ORANGE for a few seconds. Allow the charge status LED to go off before placing another battery in the charging pod. The charger is designed to charge batteries with a temperature monitoring circuit when the battery temperature is between 0°C and 45°C (32°...
-
Page 12: Fault Conditions & Advisements
Fault Conditions & Advisements When the charge status LED flashes RED, a fault condition exists. A fault condition requires immediate attention. When the status LED is solid or flashes ORANGE, you are receiving an advisement about the battery. The flash patterns for fault conditions are as follows: LED Pattern Fault Description Flashes RED... - Page 13 Fault Conditions & Advisements (continued) LED Pattern Fault Description Flashes RED Indicates battery contact is “open” and current is not passing through the (+) and (-) contacts on the battery. This warning is provided after the initial diagnostic 2 Times stage is complete.
- Page 14 Fault Conditions & Advisements (continued) The flash patterns for advisements are as follows: LED Pattern Advisement Solid ORANGE Brief reset period for charger after battery is removed. Allow the LED to go off before inserting another battery. (Battery removed.) Solid ORANGE Indicates (A) battery is too cold or (B) charger is performing a temperature diagnostic when the battery is inserted.
- Page 15 Fault Conditions & Advisements (continued) LED Pattern Advisement Flashes ORANGE Battery temperature remains at 0°C (32° F) or below after two hours of monitoring. Remove battery from charger and allow it to warm. 1 Time Flashes ORANGE Indicates charging complete, but battery is under charged. Battery voltage is below minimum level required.
-
Page 16: Warranty And Service
This is the only warranty made by Waveband. In no event will Waveband, its affiliates, subsidiaries, related entities, or their respective directors, officers, or employees, be liable for any damages beyond repair or replacement as described above, including without limitation, indirect, incidental, or consequential damages. -
Page 17: Specifications
Specifications Dimensions (W x L x H) 509 x 148 x 91 mm / 20.0 x 5.8 x 3.6 inches Weight 1.4 kg / 3.1 lbs. (charger only) Compatible Chemistries Li-Ion / LiPo / NiMH / NiCd (based on pod selected) Ambient Operating Temperature 5°... -
Page 18: Accessories
Accessories Part Number Description Information Power supply. UL listed. Input: 100-240V, WV-6SC-PS (Included with charger.) 50-60 Hz, 2.0A. Output: 15.0V, 6.0A. Power cord to connect WV-6SC-PS Length 5.0’. U.S. type plug. WV-6SC-PC to AC power. Heavy duty vehicle power adapter. Length: 24.0”... - Page 19 1912 Liberty Road Road • Unit 14 • Eldersburg, MD 21784 www.wvbandcoms.com...